Hardy Barth eCB1-LR Hoja de instrucciones
Smartmeter
eCB1-LR
Configuration manual
Configuration manual eCB1 Smartmeter
Version: 1.2.1 1
English
Contents
Contact data...................................................................................................................2
Note.................................................................................................................................................4
General information about eCB1....................................................................................................4
Meaning of LED status....................................................................................................................4
Reset function..................................................................................................................................4
Setup of direct LAN connection to the eCB1................................................................5
Anklemmen der BUS-Verbindung zwischen Wallbox und eCB1...................................7
Configuration of eCB1 LR MP+ (metering point)...........................................................8
Opening the Webinterface..............................................................................................................8
Language..........................................................................................................................................8
Date and time..................................................................................................................................9
Networksettings.............................................................................................................................1
Internal...........................................................................................................................................11
Charge connector...........................................................................................................................11
Setup finish....................................................................................................................................12
Explanation of Webinterface........................................................................................................13
Configuration of eCB1 LR PV (PV load control)............................................................14
Date and time...............................................................................................................................15
Network settings...........................................................................................................................16
House connection.........................................................................................................................17
Charging point................................................................................................................................19
Setup finish...................................................................................................................................21
Firmware-Update..........................................................................................................................22
Important settings for operation..................................................................................................22
Charge log.....................................................................................................................................25
Configuration manual eCB1 Smartmeter
Version: 1.2.1 3
Note
To prevent confusion between the different models of the eCB1 be sure to check the
model specification on the package.
General information about eCB1
Meaning of LED status
Status-LED
Permanent green The eCB1 is ready.
Slowly flashing in green The device is starting.
Qui kly flashing in green A firmware update is running.
Glowing or flashing in red or An error occurred.
orange
Network-LED
Off no connection
Permanent green connection active
Green flashing Network activity
Bus-LED
Off Device is not configured.
Green connection is okay.
Orange No device detected.
Red BUS error
Reset fun tion
You can reset the ecB1 to network settings or simply restart the device by pressing the
reset button. The time period of pressure applied is important.
Reset to fa tory settings
With a pointy object press the Reset button for 4 to 10 seconds.
Restart the eCB1
To restart use a pointy object to press the Reset-button for 1 second to 3 seconds.
The installation and configuration of the described devices should be executed in the
stated order.
Configuration manual eCB1 Smartmeter
Version: 1.2.1 4
Setup of dire t LAN onne tion to the eCB1
Step 1: Install eCB1 (if included externally) and/or connect it to the power supply.
Step 2: Integrate the eCB1 in your network a PC or a laptop with help of a LAN cable
(see image).
Please Note: Please make sure that only one unfigured eCB1 is connected to your network in order to
avoid name collisions.
1. Start your browser.
2. Type in the following URL „http://e b1.lo al“ (see image below).
1. The user interface of the eCB1 opens.
Configuration manual eCB1 Smartmeter
Version: 1.2.1 5
Should the interface not open please verify the following things:
1. The name resolution does not work.
Please open the interface via the actual IP-adress of the eCB1.
„(http://<IP>/)“
Open the desktop of your router and read the IP address of the eCB1 (see manual of your
router).
If you have Windows XP/7/8: Install Apple Bonjour®. You can find the download link on
www.apple.com. Then try to enter the URL again.
Please note: Apple Bonjour® is also included in Apple iTunes®.
Alternatively contact the network administrator.
2. The Status LED is not glowing.
If the Status LED of the eCB1 does not glow it means that the
Smartmeter is not provided with any power.
Please make sure that at least one of the phase conductors L1 and
the neutral conductor N are connected to the eCB1.
3. The Status-LED glows or blinks in red.
If the Status LED glows or blinks in red an error has occurred.
Please restart the eCB1 by pressing the Reset-button with a pointy
object for about 1-3 se onds.
4. The Network-LED is not glowing
The network cable is not properly/correctly connected to the network port if the
network-LED does not glow. Please make sure that you have inserted both ends of the
cable properly and correctly.
5. eCB1 ould not be found in the network
This means that eCB1 is not located in the same local network. Please connect the
eCB1 with the same Router/Switch as the one of your PC’s/laptop’s.
If that doesn’t solve your problem, please reset the eCB1 to its fa tory settings by
pressing the Reset-button with a pointy obje t for about 4 se onds to 10 se onds.
Configuration manual eCB1 Smartmeter
Version: 1.2.1 6
Conne ting the eCB1 and the Pµ1 via BUS
Image 1: shows the BUS-clamps of the cPµ1.
Image 2: shows the BUS-clamps of the eCB1.
(Please note the green marks in Image 1 )
Image 1
cPµ1 charging
station
Image 2
ecB1 and Bus terminal
These have to be connected as follows:
plug the brown wire (second slot on the eCB1) in
lamp 1 (shown in Image 1).
plug the bla k wire (third slot on the eCB1) in
lamp 2.
Last step you plug the blue wire (first slot on the
eCB1) in lamp 3.
Configuration manual eCB1 Smartmeter
Version: 1.2.1 7
Configuration of eCB1 LR MP (metering point)
Opening the Webinterface
Access the Webinterface of the eCB1 MP+ (metering point at the house connection) by
entering its IP address in your webbrowser.
Prior to that it has to be integrated into the network of the house. Then through the
interface of the router you can find the IP address of all eCB1 including this one.
If therer is no other configured eCB1 in your Network you can contact the eCB1 MP+ with
http://ecb1.local for first configuration.
If the Domane Name System should not work you can find the IP adress through the
Webinterface of your router.
The following page should open up:
Please click “proceed” to get to the following section:
Language
Here you can set:
- language
- the country in which you are installing the charging station
- the time zone
Configuration manual eCB1 Smartmeter
Version: 1.2.1 8
Date and time
Click “proceed” to get to the following screen:
Here you can set the time and date manually or automatically.
Manual setting
Click on the Date button and choose the current date. Then continue with the Time
button to enter the current time.
Please separate the hours minutes and seconds with colons.
To complete the settings press “set time” and the settings will be saved.
Automati setting
In this case “Date” and “Time” do not need any entries.
There are pre-set internet pages in section “NTP Server 1” and “NTP Server 2”. These will
connect you automatically with a time server.
Click on “Set time by ntp” to save your settings. If you want to connect with a different or
your own time server please enter the internet address manually.
By clicking “automati syn hronise at boot” the time will be synchronised automatically
after every outage (power network etc.).
Configuration manual eCB1 Smartmeter
Version: 1.2.1 9
Network settings
After completion of the time and date settings click on “Continue” to get to the next
section.
Choose “DHCP” as protocol.
Your DHCP Server (e.g Router) will do further settings automatically and fill the remaining
blank spaces.
There are no other settings to be made in the section except giving a hostname.
If you choose “static” as protocol please contact your network administrator in order to fill
the remaining forms according to your network.
Select a distinct hostname. Usually the device responds to the given hostname meaning
the URL will change to >givenname<.local instead. Upon delivery the hostname given is
“e b1.lo al”.
Configuration manual eCB1 Smartmeter
Version: 1.2.1 10
Otros manuales para eCB1-LR
1
Tabla de contenidos
Otros manuales de Instrumento de medición de Hardy Barth
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario