Harbor Freight Tools 97004 Manual de instalación

WIRELESS DOORBELL

Model

97004

SET UP AND OPERATING INSTRUCTIONS

Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may differ slightly from the product described herein.

Distributed exclusively by Harbor Freight Tools®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

Page 2SKU 97004 For technical questions, please call 1-800-444-3353.

SAVE THIS MANUAL

Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in

the back of the manual near the assembly diagram (or month and year of purchase if

product has no number). Keep this manual and the receipt in a safe and dry place for

future reference.

IMPORTANT SAFETY INFORMATION

In this manual, on the labeling, and all other

information provided with this product:

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation

which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazardous situation

which, if not avoided, could result in death

or serious injury.

CAUTION, used with the safety alert

symbol, indicates a hazardous situation

which, if not avoided, could result in minor

or moderate injury.

NOTICE is used to address practices not

related to personal injury.

CAUTION, without the safety alert symbol,

is used to address practices not related to

personal injury.

DANGERDANGER

WARNINGWARNING

CAUTIONCAUTION

NOTICENOTICE

CAUTIONCAUTION

Page 3SKU 97004 For technical questions, please call 1-800-444-3353.

GENERAL SAFETY RULES

WARNING! Read all instructions

Failure to follow all instructions listed below may result in electric shock,

re, and/or serious injury.

SAVE THESE INSTRUCTIONS

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Keep children and bystanders away while installing the Wireless

Doorbell. Distractions can cause you to lose control.

Personal safety

Stay alert, watch what you are doing and use common sense when installing

the Wireless Doorbell.

Use safety equipment. Always wear eye protection. Safety equipment such

as hearing protection used for appropriate conditions will reduce personal

injuries.

Store idle tools out of the reach of children and do not allow persons

unfamiliar with the Wireless Doorbell or these instructions to operate the

Wireless Doorbell.

Maintain the Wireless Doorbell. Check for breakage of parts and any other

condition that may affect the Wireless Doorbell operation. If damaged, have

the Wireless Doorbell repaired before use. Many accidents are caused by

poorly maintained products.

Use the Wireless Doorbell and accessories, in accordance with these

instructions and in the manner intended for this particular type of product.

Use of the Wireless Doorbell for operations different from those intended

could result in a hazardous situation.

SPECIFIC SAFETY RULES

Maintain labels and nameplates on the tool. These carry important safety

information. If unreadable or missing, contact Harbor Freight Tools for a

replacement.

This product is not a toy. Keep it out of reach of children.

Do not get the Wireless Doorbell wet as this will damage the unit.

The warnings, precautions, and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be

understood by the operator that common sense and caution are factors which

cannot be built into this product, but must be supplied by the operator.

Page 4SKU 97004 For technical questions, please call 1-800-444-3353.

SAVE THESE INSTRUCTIONS.

SPECIFICATIONS

Construction

Polystyrene transmitter and receiver,

steel mounting hardware and

thermoplastic anchors

Transmitter Battery (1) VA23A, MS21/MN21, A23S, 12V,

Alkaline (included)

Receiver Battery (2) AA, 1.5V (not included)

Working Distance Up to 200 Feet

UNPACKING

When unpacking, check to make sure that the item is intact and undamaged. If

any parts are missing or broken, please call Harbor Freight Tools at the number shown

on the cover of this manual as soon as possible.

SET UP INSTRUCTIONS

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the

beginning of this manual including all text under subheadings therein

before set up or use of this product.

Risk of accidental starting; resulting in serious personal

injury. Turn the Power Switch of the tool to its “OFF”

position and unplug the tool from its electrical outlet before

assembling or making any adjustments to the tool.

Note: For additional information regarding the parts listed in the following pages, refer

to the Assembly Diagram near the end of this manual.

WARNINGWARNING

Page 5SKU 97004 For technical questions, please call 1-800-444-3353.

Assembly

Installing and Replacing Batteries

Receiver Battery

Compartment

Battery Cover

(3)

Figure 1

You will have to install 2 “AA” Batteries in the Receiver (2). Remove the Battery

Cover (3) located on the back of the Receiver (2)-see Figure 1.

Insert Batteries making certain that the polarity lines up with the polarity

indicated in the Battery Compartment. Replace Battery Cover (3).

Transmitter (1)

Transmitter Battery

Cover (4)

Figure 2

To replace Transmitter Battery, rst remove the Screw (9) holding the Battery

Cover (4) on. Remove the Battery Cover by pulling it up and off.

Replace the Battery in the Battery Compartment so that the battery’s polarity

lines up with that indicated-see Figure 2.

Replace Screw (9) to hold the Battery Cover (4) on.

Mounting

Note that the Transmitter (1) and the Receiver (2) must be mounted within 200

Feet of each other.

Page 6SKU 97004 For technical questions, please call 1-800-444-3353.

The Wireless Doorbell can be mounted with two-sided Mounting Tape (5/6).

Remove backing from the Mounting Tape (5/6). Attach the backing to the

Transmitter and/or Receiver and press it into place. Make certain that the

mounting surface is dry and free of debris. Remove the backing from the

second side of the Tape and press the unit onto the desired location.

Two Mounting Screws (8) and Anchors (7) are included to secure the

Transmitter to walls. Before inserting Mounting Screws (8) with Anchors (7) into

any surface, make certain that the drilling path is clear of wiring. Drill holes for

Anchors. Insert Anchors (7) and thread in Mounting Screws (8).

Functions

Push button on Transmitter to cause Receiver to emit ringing tone.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND

ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE

MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF

ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO

THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE

PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES

THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED

AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK

AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR

REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF

REPLACEMENT PARTS THERETO.

PARTS LIST

Part Description Q’ty

1 Transmitter 1

2 Receiver 1

3 Receiver Battery Cover 1

4 Transmitter Battery Cover 1

5 Small Mounting Tape 1

Part Description Q’ty

6 Larger Mounting Tape 1

7 Anchors 2

8 Screws 2

9 Battery Cover Screw 1

Page 7SKU 97004 For technical questions, please call 1-800-444-3353.

ASSEMBLY DIAGRAM

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not

available individually as replacement parts.

Tabla de contenidos

Otros manuales de Electrodoméstico de Harbor Freight Tools

Harbor Freight Tools

Harbor Freight Tools 90416 Manual de lista de piezas

Manuales populares de Electrodoméstico de otras marcas

Mesko

Mesko MS 9613 Manual de usuario

Allied Moulded Products

Allied Moulded Products SLIDERBOX SBFB-1N Manual de usuario

Coopers of Stortford

Coopers of Stortford F996 Manual de usuario

Pella

Pella 802Q0101 Manual de usuario

Ellia

Ellia aspire ARM-1210 Manual de usuario

IKEA

IKEA VÄXER Manual de usuario

Project Source

Project Source 08-3843 Manual de usuario

impey

impey Aqua-Grade Linear Manual de usuario

JML

JML DriBUDDI Manual de usuario

ECODROP

ECODROP RV0813 Manual de usuario

AquaPur

AquaPur Terry Manual de usuario

pols potten

pols potten Taro in pot 540-300 Series Manual de usuario

AeroBed

AeroBed Premier IntelliWarmth Manual de usuario

Allen + Roth

Allen + Roth WSWS-WB1 Manual de usuario

AEG

AEG MWTK60 Manual de usuario

Sunbeam

Sunbeam heated bedding Manual de usuario

Nokia

Nokia Nokia Sleep Manual de usuario

Velleman

Velleman XMCL12 Manual de usuario