Harbor Breeze MARINA COVE II Manual de usuario
1
4009218
Harbor Breeze® is a registered trademark
of LF, LLC. All Rights Reserved.
ITEM #0275422
2889554
MODEL #JP18BZ3
JP18TI3
ATTACH YOUR RECEIPT HERE
Purchase Date
RR20391
Español p. 14
MARINA COVE II
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-251-1003, 8 a.m. - 8 p.m., EST, Monday - Sunday. You could also
READ AND SAVE THESE INSTRUCTIONS
TABLE OF CONTENTS
2
SAFETY INFORMATION
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage
that might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to
the floor.
• After you install the fan, make sure that all connections are secure to prevent the fan from falling.
• The net weight of this fan is: 21 lbs.
Safety Information ...............................................................................................................
Package Contents ...............................................................................................................4
Hardware Contents .............................................................................................................
Preparation ..........................................................................................................................
Assembly Instructions .........................................................................................................6
Operating Instructions ......................................................................................................
Care and Maintenance ......................................................................................................12
Troubleshooting .................................................................................................................12
Limited Lifetime Warranty ..................................................................................................13
2
5
5
11
SAFETY INFORMATION
3
To reduce the risk of fire, electrical shock or personal injury, use the metal wall
mounting bracket provided with the fan. Secure the wall mounting bracket directly to the
building structure on a wood stud or wood post or beam. Do not install directly to drywall.
The wood stud or wood post and its support must be able to support the moving weight of the fan
(at least 50 lbs.). The stud or wood beam must be supported directly by the building structure. Do
NOT use any other wall mounting bracket other than the one provided.
To avoid personal injury, the use of gloves may be necessary while handling fan parts with
sharp edges.
To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of personal injury or electrical shock, the fan should be installed where it will be
out of reach of children. The fan is NOT a toy -- DO NOT play with the fan or allow anyone else to
play with the fan.
To reduce the risk of personal injury or electrical shock, do not operate the fan if the cord or plug
has been damaged.
To reduce the risk of fire, avoid the use of an extension cord. If an extension cord is used, it must
be UL- or ETL-listed; NEVER use more than one extension cord to operate the fan.
To reduce the risk of personal injury, use only parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
WARNING
CAUTION
Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.
Read all instructions and safety information before installing your new fan. Review the
accompanying assembly diagrams.
Due to the bulkiness of the fan assembly, it is advisable to seek the help of another person in order
to install the fan asembly in the safest, most efficient manner.
PACKAGE CONTENTS
A
E
D
B
C
IMPORTANT REMINDER: You must use the
parts provided with this fan for proper installation
and safety.
4
F
G
H
I
J
A Fan Assembly 1
B Wall Mounting Bracket 1
C Front Cage 1
D Blade Assembly 1
E Back Cage 1
F Blade Assembly Nut 1
(preassembled)
G Back Cage Screw 3
(preassembled)
DESCRIPTIONPART QUANTITY DESCRIPTIONPART QUANTITY
H Front Cage Screw 6
(preassembled)
I Pull Chain 1
(preassembled)
J Power Cord 1
(preassembled)
K Decorative Nut 1
(preassembled)
L Fuse (Included) 1
L
K
5
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Assembly Time: 90 minutes
Tools Required for Assembly (not included): Phillips Screwdriver, Drill, Drill Bit, Stud Finder, Flathead
Screwdriver, Pliers, Wrench, Safety Glasses, Tape Measure and Stepladder
Helpful Tools (not included): Level, Pencil, Do-It-Yourself and Wiring Handbook
DANGER: Make sure the wall mounting bracket is securely attached to the building structure and
can support the full weight of the fan. Failure to do this can result in serious injury or death.
After opening top of carton, remove mounting hardware package from foam inserts. Remove fan
assembly from packing and place on carpet or on foam to avoid damage to finish.
CAUTION: Carefully check all screws, bolts and nuts on fan assembly to ensure that they are
secured.
PREPARATION
Wood
Screw
Qty. 4
+ 1 extra
AA
HARDWARE CONTENTS (shown actual size)
3.
6
Turn off circuit breakers and wall switch to the fan
supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
2.
ASSEMBLY INSTRUCTIONS
ON
OFF
ON
OFF
2
1
7 ft
min.
This fan assembly (A) can only be mounted on an
indoor wall or on an enclosed porch or enclosed
patio wall.
To prevent personal injury and damage, ensure
that the hanging location allows the fan assembly
(A) a clearance of 7 ft. from the floor to prevent
accidental contact with the blade.
CAUTION: If you are going to attach the fan
assembly (A) to a wood stud or wood post, the
stud or wood post must be wide enough and thick
enough to sustain the wall mounting bracket (B)
and the weight of the fan assembly (A).
Determine the approximate position of where you
want the fan to be located on the wall. Then,
locate the stud in the wall. Position wall mounting
bracket (B) on wood stud or wood post and mark
the location of the four holes using a pencil or a
marker (not included).
WARNING: To reduce the risk of fire,
electrical shock or personal injury, use all four
mounting holes (two at the top and two at the
bottom) in wall mounting bracket (B) when
installing wall mounting bracket (B).
A
Stud
7 Ft.
3
B
7
Wood Screw x 4
Hardware Used
AA
Stud
4
AA
AA
B
4. Use 3/32-in. drill bit (not included) to drill pilot
holes at marked locations. Then, install wall
mounting bracket (B) to mounting surface with
wood screws (AA).
WARNING: It is very important that you use
the proper hardware when installing the wall
mounting bracket (B) as this will support the fan
assembly (A).
5. Remove set screw at bottom of fan assembly (A).
With the wall mounting bracket (B) secured to the
wall and able to support the fan assembly (A), you
are now ready to hang the fan assembly (A).
Grab the fan assembly (A) firmly with two hands.
Align the four slots in the middle of the back of the
fan assembly (A) with the four hooks on the wall
mounting bracket (B) and then pull down firmly on
fan assembly (A).
WARNING: Failure to make sure all four
hooks on the wall mounting bracket (B) have
engaged completely with the four slots in the fan
assembly (A), and that the fan assembly (A) is
stable may result in injury or death.
ASSEMBLY INSTRUCTIONS
5
A
Slots
Hooks
B
Set
Screw
Replace set screw at bottom of fan assembly (A).
Tighten securely.
6. 6
A
Set
Screw
8
2
A
E
Install the three back cage screws (G)
previously removed into each of the three
holes in the center of the back cage (E) to
secure back cage (E) to motor on fan
assembly (A).
9. 9
7. 7
G
ASSEMBLY INSTRUCTIONS
Align the three holes on the outer edge of the
motor on fan assembly (A) with the three holes
in the center of the back cage (E).
8. 8
A
A
G
E
Remove the three back cage screws (G)
from the outer edge of the motor on fan
assembly (A)
Turn blade assembly nut (F) clockwise to remove
from shaft on fan motor. 10
F
10.
CC
Re-attach blade assembly nut (F) into center of
blade assembly (D) and turn counterclockwise to
secure.
12.
9
D
F
12
Motor
ASSEMBLY INSTRUCTIONS
Partially loosen preassembled set screw on blade
assembly (D). Place blade assembly (D) over motor
shaft and lock pin, making sure to align gap on the
blade assembly (D) with lock pin on motor. Turn set
screw located on the blade assembly (D) clockwise
to secure blade assembly (D) to fan motor.
11.
D
Set
screw
11
Gap
Shaft
Lock
Pin
Shaft
Plug
Insert power cord (J) preassembled on fan
assembly (A) into proper wall outlet.
WARNING: The power cord is equipped
with a three-prong grounded plug that must
be inserted into a matching receptacle. Under
no circumstances must the grounding prong
be cut off the plug. Where a two-prong wall
receptacle is encountered, it must be
replaced with a properly grounded
three-prong receptacle installed in
accordance with the National Electrical Code
and all applicable local codes and
ordinances.This work must be done only by a
qualified electrician, using copper wire only.
C
13
Hook
H
E
Remove all six front cage screws (H) from edge of
back cage (E).
Place hook at top of front cage (C) over edge at top
of back cage (E). NOTE: Make sure hook engages
and all front and back cage holes match up; this will
allow the front cage (C) and the back cage (E) to
hang together while you re-insert the front cage
screws (H) into the the front and back cage holes.
Insert front cage screws (H) into both holes at top of
front cage (C), then tighten. Insert remaining front
cage screws (H). Tighten front cage screws (H),
alternating from one side of front cage (C) to the
other until all front cage screws (H) are completely
secured.
13.
A
10
H
ASSEMBLY INSTRUCTIONS
14. 14
J
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Admirador de Harbor Breeze
Harbor Breeze
Harbor Breeze BTH44ABZC5C Manual de usuario
Harbor Breeze
Harbor Breeze 40662 Manual de usuario
Harbor Breeze
Harbor Breeze 80210 Manual de usuario
Harbor Breeze
Harbor Breeze CGR60WW3LR Manual de usuario
Harbor Breeze
Harbor Breeze 40314 Manual de usuario
Harbor Breeze
Harbor Breeze BELCARRA CE-JP13BNK6RC Manual de usuario
Harbor Breeze
Harbor Breeze RC103L Manual de usuario
Harbor Breeze
Harbor Breeze ARMITAGE CC52WW5C Manual de usuario
Harbor Breeze
Harbor Breeze ALTISSA Manual de usuario
Harbor Breeze
Harbor Breeze KEYPORT HUGGER 40141 Manual de usuario
Harbor Breeze
Harbor Breeze PRESTWICK 42868 Manual de usuario
Harbor Breeze
Harbor Breeze 40107 Manual de usuario
Harbor Breeze
Harbor Breeze 873 Manual de usuario
Harbor Breeze
Harbor Breeze WAVEPORT STYLE E-WK52NWZ5C1 Manual de usuario
Harbor Breeze
Harbor Breeze RLC52WW5C1R Manual de usuario
Harbor Breeze
Harbor Breeze LP8072LAZ Manual de usuario
Harbor Breeze
Harbor Breeze CE-JP13EB6RC Manual de usuario
Harbor Breeze
Harbor Breeze E-CAF56OSB5CRC Manual de usuario
Harbor Breeze
Harbor Breeze PACIFIC GROVE 40101 Manual de usuario
Harbor Breeze
Harbor Breeze VALDOSTA L1120H-BK Manual de usuario
