Hantek HDG3000C Series Manual de usuario

HDG3000C series

Arbitrary waveform signal generator

Quick Guide

2022.05

Warranties and Declarations

The copyright of this document belongs to Qingdao Hantek Electronics Co., LTD.

Statement

Qingdao Hantek Electronics Co., Ltd. reserves the right to amend this document without prior notice.

Qingdao Hantek Electronics Co., Ltd. promises that the information provided is correct and reliable but

does not guarantee that this document is free from errors. Before using this product, please make sure

that the specifications of relevant technical documents are the latest effective version. If you use

documents or products of Qingdao Hantek Electronics Co., LTD and need products, patents or works

of third parties to cooperate with them, you shall be responsible for obtaining the consent and

authorization of the third parties. The above consent and authorization shall not be the liability of

Hantek.

Product certification

Hantek certified HDG300C-series arbitrary waveform signal generators to meet China's national

industry standards and has passed the CE certification.

If you have any questions when using the products of Qingdao Hantek Electronics Co., LTD., you can

obtain service and support through the following ways:

Email: service@hantek.com, supp[email protected]

Website: http://www.hantek.com

Safety requirements

1 Safety requirements

1.1 Summary of general safety matters

Read the following safety precautions carefully to avoid injury and to prevent damage to

this product or any product connected. To avoid possible dangers, please use this

product in accordance with the regulations.

⚫Only professionally authorized personnel can perform repairs.

⚫Use the right power cable.

Use the power cable approved by the country in which the product is used only.

⚫Connect and disconnect correctly.

Before connecting the probe to the circuit being measured, please connect the

probe to the oscilloscope first. Before disconnecting the probe from the oscilloscope,

please disconnect the probe and the circuit under test first.

⚫Ground the product.

To avoid electric shocks, the product is grounded through a grounding conductor of

the power cable. The grounding conductor must be connected to the ground before

connecting the input or output terminals of the product. Ensure that the product is

properly grounded.

⚫Connect the probe properly.

The ground wire of the probe is the same as the ground potential. Do not connect

the ground wire to high voltage.

⚫View all terminal rating values.

To avoid fire or excessive current, please check all rating values and signs on the

product. Please consult the product manual for details of the rating values before

connecting the product.

⚫Do not operate with the cover open.

Do not run the product with the cover or panel open.

⚫Avoid circuit exposure.

Do not touch exposed connectors and components after power is switched on.

⚫Do not operate if the product is suspected to be faulty.

If you suspect that the product has been damaged, please ask qualified

maintenance personnel to check it.

Safety requirements

⚫Maintain proper ventilation.

⚫Do not operate in a humid environment.

⚫Do not operate in inflammable or explosive environment.

⚫Please keep the product surface clean and dry.

Warning:

Equipment that meets Class A requirements may not provide adequate protection

for broadcast services in residential environments.

1.2 Safety terms and symbols

Safety terms in this manual:

Dangerous

Indicates that immediate damage may be caused to you if you perform this

operation.

Warning:

Indicates that it may not cause immediate damage to you if you perform this

operation.

Note

Indicates that you may cause damage to this product or other properties if you do

so.

Safety terms on the product:

Warning:

Indicates a potential hazard to you if you do not perform this operation.

Safety symbols on the product:

Safety requirements

1.3 Measurement category

Measurement category

This instrument can be used for measurement under class I.

Warning:

This instrument is only allowed to be used in the specified measurement class.

Measurement class definition

⚫Class I refers to measurements taken on a circuit not directly connected to

the main power supply. For example, measurements made on circuits that are not

exported from a main power supply, especially from a protected (internal) main

power supply. In the latter case, the instantaneous stress will change. Therefore,

the user should understand the instantaneous capacity of the instrument.

⚫Class II refers to measurements taken on a circuit directly connected to

low-voltage instruments. For example, measurements made on household

appliances, portable tools, and similar equipment.

⚫Class III refers to measurements taken on construction equipment. For

example, measurements made on switchboards, circuit breakers, circuits (including

cables, busbars, junction boxes, switches, sockets) in fixed equipment, as well as

equipment for industrial use and certain other equipment (for example, fixed motors

permanently connected to fixed instruments).

⚫Class IV refers to measurements taken at the source of low-voltage

equipment. For example, measurements made on electricity meters, primary

overcurrent protection equipment, and pulse control units.

1.4 Working conditions

Temperature

Operating temperature: 0℃- 45℃

Storage temperature: 20℃- 60℃

Humidity

≤+104℉(≤+40°C): relative humidity≤90%

106℉~122℉(+41°C ~50°C): relative humidity≤60%

Warning:

To avoid the danger of short circuit or electric shock, do not operate the

instrument in a humid environment.

Altitude

Safety requirements

When operating: below 3,000 meters.

When not operating: below 15,000 meters.

Installation (over voltage) Class This product is powered by a main power source that

complies with Installation (over voltage) Class II.

Warning:

Make sure that no overvoltage (such as that caused by lightning) reaches the

product. Otherwise the operator may be in danger of receiving an electric shock.

Installation (overvoltage) Class definition

Class I refers to the signal level, which is applicable to the measuring terminal of the

instrument connected to the source circuit. Measures have been taken to limit the

instantaneous voltage to the corresponding low level.

Class II refers to the local distribution level, which is applicable to instruments connected

to the mains (AC) supply.

Degree of pollution

Class 2

Pollution level definition

⚫Level 1: No pollution, or only dry non-conductive pollution. This pollution level has

no impact. For example: clean room or air-conditioned office environment.

⚫Level 2: Generally, only dry non-conductive pollution. Temporary conduction due to

condensation may sometimes occur. For example: general indoor environment.

⚫Level 3: Conductive pollution, or dry non-conductive pollution becoming conductive

due to condensation. For example, an outdoor environment with a canopy.

⚫Level 4: Permanent conductive pollution through conductive dust, rain, or snow.

For example: outdoor places.

Security level

Level 1 - Grounded products

1.5 Maintenance and cleaning

Maintenance:

Do not make the LCD exposed to direct sunlight for a long time when placing the

oscilloscope.

Cleaning:

Regularly check the oscilloscope and probe according to the requirements of the

operating conditions, please follow the following steps to clean the outer surface of the

Safety requirements

instrument:

1) Using a lint-free cloth to remove the dust from the outside of the oscilloscope and

probe. Please be careful to avoid scratching the smooth display filter material.

2) Using a soft cloth soaked with water to clean the oscilloscope. For more thoroughly

clean, use 75% isopropyl alcohol aqueous solvent

Note:

To avoid damage to the oscilloscope or the surface of the probe, please do not

use any corrosive reagent or chemical cleaning reagent.

Warning:

Before repowering, please make sure the instrument is completely dry, to avoid

electrical short circuit or even personal injury caused by moisture.

1.6 Environmental Precautions

The following sign indicates that this product conforms to the requirements set out by the

WEEE Directive 2002/96/EC.

Equipment recycling:

Producing the instrument requires the extraction and use of natural resources. Some

substances contained in the instrument may be harmful to the environment or human

health if the product is not disposed of properly. To avoid the release of harmful

substances into the environment and reduce the use of natural resources, it is

recommended that appropriate methods be used to recycle this product to ensure that

most of the materials can be correctly reused.

Document overview

2 Document overview

This document is used to guide the user to quickly understand the front and back panels,

user interfaces, and basic operation methods of the HDG3000C-series signal

generators.

Tip:

The latest version of this manual can be downloaded at (http://www.hantek.com).

Document number:

202205

Software version:

Software upgrade may change or increase product functionalities, please pay attention

to Hantek website for the latest version.

Document format conventions:

1 Keys

Use "square brackets + text (bold)" to represent front panel keys, such as [Utility] for the

"Utility" key.

2 Menu

Use blue menu text (bold) to represent a menu option, for instance, Basic Settings

indicates clicking the "Basic Settings" option on the current operation interface to enter

the configuration menu of "Basic Settings".

3 Operation flow

Use ">" to indicate the next operation, for instance, [Utility] > Store indicates clicking

[Utility] and then click the Store function key.

4 Knob

Symbol

Knob

Multi-function knob

Table 2.1 Knob

Document content conventions:

The HDG3000C signal generator contains the following models.

Document overview

Model

Number of

channels

Maximum

frequency

CH1/CH2 sampling

rate

CH3 sampling

rate

HDG3023C

25MHz

300MS/s

150MSa/s

HDG3043C

40MHz

300MS/s

150MSa/s

HDG3063C

60MHz

300MS/s

150MSa/s

HDG3083C

80MHz

300MS/s

150MSa/s

HDG3103C

100MHz

300MS/s

150MSa/s

Table 2.2 Model

General checking

3 General checking

Check the shipping package

After receiving the oscilloscope, please follow the following steps to check the instrument:

Check whether there is any damage caused by transportation: If the packaging cartons

or protective foam pads are seriously damaged, please keep them until the whole

machine and accessories pass the electrical and mechanical testing.

Check the accessories

The details of the accessories are provided inAppendix A: Accessories at the end of the

user manual. If you find any accessory missing or damaged, please contact the dealer

responsible for this business.

Check the machine

If you find the instrument is damaged, not working properly, or unable to pass the

performance test, please contact the dealer responsible for this business.

Otros manuales para HDG3000C Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Hantek

Hantek

Hantek 1832C Manual de usuario

Hantek

Hantek HDG1000A Manual de usuario

Hantek

Hantek HT300B Manual de usuario

Hantek

Hantek CC-650 Manual de usuario

Hantek

Hantek DSO8000 Series Manual de usuario

Hantek

Hantek LA5034 Manual de usuario

Hantek

Hantek DSO3062L Manual de usuario

Hantek

Hantek Hantek2000 Series Manual de usuario

Hantek

Hantek 4032L Manual de usuario

Hantek

Hantek HTM200 Series Manual de usuario

Hantek

Hantek DSO3102 Manual de usuario

Hantek

Hantek HSA2030 Manual de usuario

Hantek

Hantek HT8000 Series Manual de usuario

Hantek

Hantek CC-800 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario