Hanna Instruments PICCOLO 2 HI 98112 Manual de usuario

PICCOLO®

PICCOLO®2

PICCOLO®plus

ATC pH Testers

www.hannainst.com

SPECIFICATIONS PICCOLO®PICCOLO®2 PICCOLO®+

(HI 98111) (HI 98112) (HI 98113)

Range 1.00 to 13.00 pH

-- -- 0.0 to 70.0°C

Resolution 0.01 pH 0.01 pH 0.01 pH / 0.1°C

Accuracy (@20°C) ±0.01 pH ±0.01 pH ±0.01 pH / ±1°C

Calibration Manual, 2 point, through Offset & Slope trimmers

Temperature Compensation

Automatic, 0 to 70ºC (32 to 150°F)

Probe (included) HI 1280 HI 1290 HI 1295

Battery Type / Life 3 x 1.5V alkaline / approx. 100 hours

Environment 0 to 50ºC (32 to 122ºF); RH max 95%

Dimensions 194x29x15 265x29x15 265x29x15 mm

(with probe) (7.6x1.1x0.6") (10.4x1.1x0.6") (10.4x1.1x0.6")

Weight 70 g (2.5 oz.)

ISTPICCOLO 05/05

Each Piccolo®model is supplied complete with pH electrode, pH 4.01

and pH 7.01 buffer sachets, calibration screwdriver, rugged carrying

case and instructions.

ACCESSORIES

HI 1280 Spare pH electrode for Piccolo®(90 mm/3.5")

HI 1290 Spare pH electrode for Piccolo®2(160 mm/6.3")

HI 1295 Spare pH electrode for Piccolo®plus (160 mm/6.3")

HI 70004P pH 4.01 buffer solution, 20 mL sachet, 25 pcs

HI 70007P pH 7.01 buffer solution, 20 mL sachet, 25 pcs

HI 70010P pH 10.01 buffer solution, 20 mL sachet, 25 pcs

HI 7004M pH 4.01 buffer solution, 230 mL bottle

HI 7007M pH 7.01 buffer solution, 230 mL bottle

HI 7010M pH 10.01 buffer solution, 230 mL bottle

HI 70300M Electrode storage solution, 230 mL bottle

HI 7061M Electrode cleaning solution, 230 mL bottle

HI 731326 Calibration screwdriver (20 pcs)

Piccolo is a registered Trademark of

Hanna Instruments

OPERATION

• Connect the electrode

to the meter as shown

in the drawing, and

turn the meter on.

Note: The PICCOLO®plus model

is provided with an OFF/pH/°C

switch. Select the "pH" position

for pH readings, or "°C" for tem-

perature measurements.

• Remove the protective cap and

dip the electrode in the sample

to be measured, without exceed-

ing the maximum immersion

level. Stir gently and wait for the

reading for stabilize.

• The pH value automatically com-

pensated for temperature varia-

tions will be displayed.

• After use, always switch the

meter off.

MAINTENANCE

• To reactivate a dry electrode,

immerse it in HI 70300 storage

solution for 4 hours.

BATTERY REPLACEMENT

When the meter cannot be

switched on or the display fades,

batteries should be replaced.

Unscrew the upper

screw and slide off

the battery compart-

ment. Replace all 3

batteries while pay-

ing attention to the

correct polarity.

Reinsert the cover and tighten the

screw. After battery replacement,

it is always recommended to

recalibrate the instrument.

Batteries should only be replaced

in a safe area and using the bat-

tery type specified in this instruc-

tion manual.

WARRANTY

These meters are guaranteed for one year against de-

fects in workmanship and materials when used for their

intended purpose and maintained according to instruc-

tions. Electrodes are guaranteed for six months. This

warranty is limited to repair or replacement free of charge.

Damages due to accident, misuse, tampering or lack of

prescribed maintenance are not covered. If service is

required, contact the dealer from whom you purchased

the instrument. If under warranty, report the model num-

ber, date of purchase, serial number and the nature of

the failure. If the repair is not covered by the warranty, you

will be notified of the charges incurred. If the instrument

is to be returned to Hanna Instruments, first obtain a

Returned Goods Authorization Number from the Customer

Service department and then send it with shipment costs

prepaid. When shipping any instrument, make sure it is

properly packaged for complete protection.

Recommendations for Users

Before using these products, ensure that they are entirely

suitable for the environment in which they are used. Op-

eration of these instruments in residential areas could

cause unacceptable interference to radio and TV equip-

ment. The glass bulb at the end of the electrode is sen-

sitive to electrostatic discharges. Avoid touching this glass

bulb at all times. During operation of the instrument, ESD

wrist straps should be worn to avoid possible damage to

the pH electrode by electrostatic discharges. Any varia-

tion introduced by the user to the supplied equipment

may degrade the instrument’s EMC performance. To avoid

electrical shock, do not use these instruments when volt-

age at the measurement surface exceeds 24Vac or 60Vdc.

To avoid damage or burns, do not perform any measure-

ment in microwave ovens.

• After use, rinse the electrode with water and store it with a few drops

of storage solution in the protective cap.

CALIBRATION

• To access the calibration trimmers, slide down the probe. Then turn

the meter on.

• Dip the probe in HI 7007 (pH 7.01) buffer solution and allow the

reading to stabilize. With the supplied screwdriver, adjust the "pH7"

trimmer to read "7.01" pH.

• Rinse the electrode with water and dip it in the second buffer.

Use HI 7004 (pH 4.01) buffer if the solution to be tested is acidic, or

HI 7010 (pH 10.01) for alkaline samples.

• Allow the reading to stabilize, then adjust the "pH 4/10" trimmer to

read "4.01" or "10.01" pH.

• The calibration is now complete and the electrode can be slided

back to its normal position.

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de prueba de Hanna Instruments

Hanna Instruments

Hanna Instruments HI 38079 Manual de usuario

Hanna Instruments

Hanna Instruments HI 95707C Manual de usuario

Hanna Instruments

Hanna Instruments HI98201 Manual de usuario

Hanna Instruments

Hanna Instruments HI 9811-0 Manual de usuario

Hanna Instruments

Hanna Instruments HI 95711C Manual de usuario

Hanna Instruments

Hanna Instruments HI 3831T Manual de usuario

Hanna Instruments

Hanna Instruments Foodcare HI981031 Manual de usuario

Hanna Instruments

Hanna Instruments Foodcare HI981035 Manual de usuario

Hanna Instruments

Hanna Instruments Pool Line HI983044 Manual de usuario

Hanna Instruments

Hanna Instruments Primo Series Manual de usuario

Hanna Instruments

Hanna Instruments HI 98204 Manual de usuario

Hanna Instruments

Hanna Instruments HI 3830 Manual de usuario

Hanna Instruments

Hanna Instruments Gro Line HALO 2 Manual de usuario

Hanna Instruments

Hanna Instruments Foodcare HI981036 Manual de usuario

Hanna Instruments

Hanna Instruments Foodcare HI981036 Manual de usuario

Hanna Instruments

Hanna Instruments HI 38039 Manual de usuario

Hanna Instruments

Hanna Instruments HI 38077 Manual de usuario

Hanna Instruments

Hanna Instruments HI 38078 Manual de usuario

Hanna Instruments

Hanna Instruments HI 98103 Manual de usuario

Hanna Instruments

Hanna Instruments UPW HI 98309 Manual de usuario

Hanna Instruments

Hanna Instruments HI 38040 Manual de usuario

Hanna Instruments

Hanna Instruments HI510 Manual de usuario

Hanna Instruments

Hanna Instruments HI 38076 Manual de usuario

Hanna Instruments

Hanna Instruments HI 96721C Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario