Hanna Instruments UPW HI 98309 Manual de usuario

UPW

HI 98309

Ultra Pure Water Tester

SPECIFICATIONS

Range 0.000 to 1.999 µS/cm

Resolution 0.001 µS/cm

Accuracy (@20°C/68°F) ±2% f.s.

Typical EMC Deviation ±0.5% f.s.

Environment 0 to 50°C (32 to 122°F);

95% RH non-condensing

Battery Type 4 x 1.5V alkaline

Battery Life approx. 120 hours of use

Dimensions 175 x 41 x 23 mm

(6.9 x 1.6 x 0.8")

Weight 95 g (3.4 oz.)

ACCESSORIES

HI 73309 Spare probe

HI 731326 Calibration screwdriver (20 pcs)

WARRANTY

This meter is guaranteed for one year against defects in

workmanship and materials when used for its intended pur-

pose and maintained according to instructions. Probes are

guaranteed for six months. This warranty is limited to repair

or replacement free of charge. Damages due to accident,

misuse, tampering or lack of prescribed maintenance are

not covered. If service is required, contact the dealer from

whom you purchased the instrument. If under warranty, re-

port the model number, date of purchase, serial number

and the nature of the failure. If the repair is not covered by

the warranty, you will be notified of the charges incurred. If

the instrument is to be returned to Hanna Instruments, first

obtain a Returned Goods Authorization Number from the

Customer Service department and then send it with ship-

ment costs prepaid. When shipping any instrument, make

sure it is properly packaged for complete protection.

The UPW is in compliance with the CE directives.

IST98309 R5 05/05 www.hannainst.com

OPERATION

• Remove the protective cap, rinse the tester

with distilled water, up to the maximum im-

mersion level.

• Turn the UPW on and immerse

it into the solution to be tested

without exceeding the maximum

immersion level.

• Stir gently and wait for the read-

ing to stabilize.

• The display will show the measurement ex-

pressed in µS/cm unit.

• To translate the reading into Mega-ohm, refer

to the following table.

CALIBRATION

The UPW tester is factory-calibrated with freshly

prepared low-conductivity solutions.

In fact, due to their high instability, calibration

solutions in the UPW range (below 2 µS/cm)

can not be supplied with the meter.

However, if your meter needs to be recalibrated,

use a 1.500 µS/cm solution prepared by a

qualified laboratory and keep it airtight.

• Immerse the probe into the calibration solution

and allow the reading to stabilize.

• With a small screwdriver, adjust the calibration

trimmer on the meter side until the display

shows the solution value.

BEPS AND BATTERY REPLACEMENT:

UPW is provided with BEPS (Battery Error Pre-

venting System) which avoids any erroneous reading

due to low battery level, by automatically switch-

ing the meter off.

To replace the batteries, slide off the battery

compartment cover and replace all four 1.5V

batteries, while paying attention to the correct

polarity.

Batteries should only be replaced in a non-

hazardous area and using the battery type

specified in this instruction manual.

Reistance of

Distilled/Deionized

Water

(MegaOhm)

Equivalent

UPW reading

(µS/cm)

1.000

0.500

0.200

0.100

0.067

0.050

PROBE REPLACEMENT

For replacing the probe, contact your Dealer or

the nearest Hanna Service Center.

Otros manuales de Equipo de prueba de Hanna Instruments

Hanna Instruments

Hanna Instruments HALO2 HI9810452 Manual de usuario

Hanna Instruments

Hanna Instruments Foodcare HI981035 Manual de usuario

Hanna Instruments

Hanna Instruments HI 96724C Manual de usuario

Hanna Instruments

Hanna Instruments HI 98121 Manual de usuario

Hanna Instruments

Hanna Instruments HI9810372 Manual de usuario

Hanna Instruments

Hanna Instruments HI 95706C Manual de usuario

Hanna Instruments

Hanna Instruments HI 3831T Manual de usuario

Hanna Instruments

Hanna Instruments GroLine HALO2 HI9810302 Manual de usuario

Hanna Instruments

Hanna Instruments Gro Line HI98318 Manual de usuario

Hanna Instruments

Hanna Instruments HI 38077 Manual de usuario

Hanna Instruments

Hanna Instruments HI 3812 Manual de usuario

Hanna Instruments

Hanna Instruments pHep+ HI98108 Manual de usuario

Hanna Instruments

Hanna Instruments Gro Line HALO 2 Manual de usuario

Hanna Instruments

Hanna Instruments HI 98103 Manual de usuario

Hanna Instruments

Hanna Instruments 3815 Manual de usuario

Hanna Instruments

Hanna Instruments Foodcare HI981034 Manual de usuario

Hanna Instruments

Hanna Instruments HI 38081 Manual de usuario

Hanna Instruments

Hanna Instruments HI 99121 Manual de usuario

Hanna Instruments

Hanna Instruments HI 83749 Manual de usuario

Hanna Instruments

Hanna Instruments HI 93739 Manual de usuario

Hanna Instruments

Hanna Instruments Foodcare HI981036 Manual de usuario

Hanna Instruments

Hanna Instruments HI96107 Manual de usuario

Hanna Instruments

Hanna Instruments HI510 Manual de usuario

Hanna Instruments

Hanna Instruments HI 38080 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario