Hanna Instruments HI99162 Manual de usuario
HI99162
Waterproof
pH & Temperature Meter
for Milk
INSTRUCTION MANUAL
All rights are reserved. Reproduction in whole or in part is
prohibited without the written consent of the copyright owner, Hanna
Instruments Inc., Woonsocket, Rhode Island, 02895, USA.
Thank you for choosing a Hanna Instruments product.
Please read this instruction manual carefully before
using this meter.
This manual will provide you with the necessary
information for correct use of this meter, as well as
a precise idea of its versatility.
If you need additional technical information, do not
our worldwide contact list at www.hannainst.com.
Dear
Customer,
3
TABLE OF CONTENTS
Preliminary examination ...........................................
General description and Intended use ........................
Main features...........................................................
Specifications...........................................................
Display description ...................................................
Operational guide.....................................................
Meter setup..............................................................
Battery replacement..................................................
Accessories...............................................................
Electrode maintenance..............................................
Certification..............................................................
Recommendations for users.......................................
Warranty .................................................................
4
5
7
9
15
6
8
16
14
17
18
19
19
4
PRELIMINARY EXAMINATION
PRELIMINARY EXAMINATION
Remove the instrument and accessories from the packaging
and examine it carefully to make sure that no damage
has occurred during shipping. Notify your nearest Hanna
Instruments Customer Service Center if damage is observed.
Each HI99162 is delivered in a rugged carrying case and
is supplied with:
• FC1013 pH/temperature probe with DIN connector and
1m (3.3’) cable
• HI70004 pH 4.01 buffer (1 sachet)
• HI70007 pH 7.01 buffer (1 sachet)
• HI700640 electrode cleaning solution for milk deposits
(2 sachets)
• 100 mL beaker (1 pcs.)
• 1.5V AAA alkaline batteries
• Instrument quality certificate
• Electrode quality certificate
• Instruction manual
Note: Save all packing material until you are sure that
the instrument works correctly. Any damaged or defective
item must be returned in its original packing material
with the supplied accessories.
5
GENERAL DESCRIPTION AND INTENDED USE
GENERAL DESCRIPTION AND INTENDED USE
The HI99162 portable pH meter together with a FC1013
combination pH electrode, is designed to measure pH of
milk.
The HI99162 features a two button operation system and
is simple to use. It has a waterproof and compact casing,
large dual‑line display, and automatic pH calibration at
one or two points.
The FC1013 is a specially designed pH electrode intended
for the direct determination of pH in milk. The FC1013 pH
probe has a durable PVDF body that can be safely taken
on the dairy farm or production floor. It features an open
junction reference system that is resistant to clogging from
milk‑based solids. The FC1013 has a built‑in temperature
sensor for temperature compensated pH readings and
an integrated preamplifier to provide measurements
impervious to noise and electrical interferences.
6
MAIN FEATURES
MAIN FEATURES
• Simultaneous pH and temperature measurements on a
large dual‑line LCD display
• Automatic pH calibration at one or two points within
two memorized buffer sets (standard or NIST)
• Selectable temperature unit (°C or °F)
• Electrode condition indicator
• mV of pH measurement for electrode check
• FC1013 dedicated pH with integrated temperature sensor
• Probe quick connect system
• Battery life indication and low battery detection
• Keystroke confirmation tone
• Auto‑off function
• Waterproof casing IP67
7
SPECIFICATIONS
Range*
‑2.00 to 16.00 pH / ‑2.0 to 16.0 pH
±825 mV (pH‑mV)
‑5.0 to 105.0 °C/23.0 to 221.0 °F
Resolution
0.01 pH / 0.1 pH
1 mV
0.1 °C/0.1 °F
Accuracy
@ 25°C / 77°F
±0.02 pH / ±0.1 pH
±1 mV (pH‑mV)
±0.5 °C up to 60 °C; ±1.0 °C outside
±1.0 °F up to 140 °F; ±2.0 °F outside
Temperature
compensation
Automatic
‑5.0 to 105.0 °C/23.0 to 221.0 °F
pH calibration
Automatic, 1 or 2 point selectable buffer
set Standard: 4.01;7.01;10.01 or
NIST: 4.01;6.86;9.18
Probe (included)
FC1013 preamplified pH and
temperature probe, DIN connector and
1 m (3.3’) cable
Battery type/life 1.5V AAA (3 pcs.)
approx. 1400 hours of continuous use
Auto‑off user selectable: after 8 min, 60 min or
disabled
Environment 0 to 50 °C (32 to 122 °F)
RH max. 100%
Meter dimensions 154 x 63 x 30 mm (6.1 x 2.5 x 1.2”)
Weight
(with batteries) 196 g (6.91 oz.)
Case ingress
protection rating IP67
* the FC1013 is limited to be used from 0 to 13 pH and from 0 to
80 °C temperature (32 to 176 °F).
SPECIFICATIONS
8
DISPLAY DESCRIPTION
DISPLAY DESCRIPTION
1 Automatic Temperature Compensation indicator
2 Stability indicator
3 Battery percentage
4 Electrode condition indicator
5 Low battery indicator
6 Measurement unit
7 Primary LCD
8 Temperature unit
9 Secondary LCD
10 Meter modes indicator
11 pH calibration buffer(s) used
9
OPERATIONAL GUIDE
OPERATIONAL GUIDE
Each meter is supplied with batteries. Before using the meter
for the first time, open the battery compartment and insert
batteries, observing the polarity (see “Battery Replacement”).
CONNECTING THE ELECTRODE
With the meter turned off, connect the FC1013 probe to the
DIN socket on the bottom of the meter by aligning the pins
and pushing in the plug firmly. Remove the protective cap
from the probe before taking any measurements.
TURNING THE METER ON
To turn the meter ON, press the button on the
front of the meter. If it does not turn on, make
sure that the batteries are properly installed in their place.
The meter is provided with an active acoustic signal when
a key is pressed. At start‑up the meter displays all LCD
segments for a few seconds, followed by the percentage
indication of the remaining battery life, displaying “WAIT“
until electrode check is in process then the meter enters the
normal measurement mode.
Battery life
Measurement
mode
LCD
check up
→ →
→
Electrode
check
Note: The meter detects the presence and the type of the
probe at its input.
- If the probe is not connected the message “NO”
”PROBE“ appears alternatively on the secondary LCD
with “---“ blinking on the first LCD line.
- If the probe is not compatible “WRONG” ”PROBE“
message appears alternatively on the secondary LCD
with “---“ blinking on the first LCD line.
- If the readings are out of range, the nearest range
limits are displayed blinking (e.g. -2.00 pH -5.0 °C).
10
OPERATIONAL GUIDE
pH MEASUREMENT & CALIBRATION
Make sure the meter has been calibrated before use.
If the probe is dry, soak it in HI70300 storage solution for
30 minutes to reactivate it. If soiled, clean the electrode
by soaking in cleaning solution for 20 minutes, then rinse
the tip and soak in storage solution at least 30 minutes
before use.
Rinse the electrode off well and shake off excess droplets.
Recalibrate before using.
Submerge the probe in the sample to
be tested while stirring it gently. Wait
until the tag on the LCD disappears.
SELECTING MEASUREMENT RANGE
While in measurement mode, press the SET button to select
pH or pH‑mV measurement on the first LCD line.
FREEZING MEASUREMENT VALUES
While in measurement mode, press and hold the SET
button until “HOLD“ appears on the secondary LCD. The
“HOLD“ remains for 1 second and reading of pH, mV
and temperature will be frozen on the LCD with“H” blinking.
→
Press any button to resume active measurements.
ENTERING CALIBRATION MODE
Press and hold the button until ”POWER” and tag
is replaced by “STD“ and tag. Release the button.
ENTERING SETUP MODE
Press and hold button until “STD“ and tag is
replaced by “SETUP“ and tag. Release the button.
TURNING THE METER OFF
Whileinmeasurement mode,pressthe button.”POWER”
and tag will appear. Release the button.
Tabla de contenidos
Otros manuales de Instrumento de medición de Hanna Instruments
Hanna Instruments
Hanna Instruments HI98198 OPDO Manual de usuario
Hanna Instruments
Hanna Instruments HI 8314 Manual de usuario
Hanna Instruments
Hanna Instruments HI 83200 Manual de usuario
Hanna Instruments
Hanna Instruments HI 93733 Manual de usuario
Hanna Instruments
Hanna Instruments HI 96762C Manual de usuario
Hanna Instruments
Hanna Instruments HALO2 HI9810442 Manual de usuario
Hanna Instruments
Hanna Instruments HI 8314 Manual de usuario
Hanna Instruments
Hanna Instruments HI 758 Manual de usuario
Hanna Instruments
Hanna Instruments LP 2000-11 Manual de usuario
Hanna Instruments
Hanna Instruments HI 4321 Manual de usuario
Hanna Instruments
Hanna Instruments pHep 98107 Manual de usuario
Hanna Instruments
Hanna Instruments HI 9813-6 Manual de usuario
Hanna Instruments
Hanna Instruments HI 9214 Manual de usuario
Hanna Instruments
Hanna Instruments HI 991301 Manual de usuario
Hanna Instruments
Hanna Instruments HI 991401 Manual de usuario
Hanna Instruments
Hanna Instruments GroLine HI98168 Manual de usuario
Hanna Instruments
Hanna Instruments HI83303 Manual de usuario
Hanna Instruments
Hanna Instruments HI84534-01 Manual de usuario
Hanna Instruments
Hanna Instruments HI 83214 Manual de usuario
Hanna Instruments
Hanna Instruments HI 93711 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario