Hanna Instruments HI96713C Manual de usuario

INSTRUCTION MANUAL

HI96713C

Phosphate Low Range ISM

Thank you for choosing a Hanna Instruments product.

Please read this instruction manual carefully before using the instrument.

This manual will provide you with the necessary information for correct use of

the instrument, as well as a precise idea of its versatility.

If you need additional technical information, do not hesitate to e‑mail us at

[email protected] or view our worldwide contact list at www.hannainst.com.

All rights are reserved. Reproduction in whole or in part is prohibited without the written consent

of the copyright owner, Hanna Instruments Inc., Woonsocket, Rhode Island, 02895, USA.

Dear

Customer,

PRELIMINARY EXAMINATION .............................................................................................

GENERAL DESCRIPTION .....................................................................................................

ABBREVIATIONS ...............................................................................................................

SPECIFICATIONS ...............................................................................................................

PRECISION AND ACCURACY ...............................................................................................

PRINCIPLE OF OPERATION ................................................................................................

FUNCTIONAL DESCRIPTION ...............................................................................................

ERRORS AND WARNINGS ..................................................................................................

GENERAL TIPS FOR AN ACCURATE MEASUREMENT ..............................................................

STARTUP ..........................................................................................................................

MEASUREMENT PROCEDURE .............................................................................................

VALIDATION PROCEDURE ...................................................................................................

CALIBRATION PROCEDURE .................................................................................................

GLP .................................................................................................................................

BATTERY MANAGEMENT ....................................................................................................

BATTERY REPLACEMENT ....................................................................................................

ACCESSORIES ...................................................................................................................

TABLE OF CONTENTS

Please examine this product carefully. Make sure that the instrument is not damaged. If any damage

occurred during shipment, please contact your local Hanna Instruments Office.

Each HI96713 Ion Selective Meter is supplied complete with:

• Sample Cuvettes and Caps (2 pcs.)

• CAL Check™ standard cuvettes

• 9V Battery

• Scissors

• Cloth for wiping cuvettes

• Instrument quality certificate

• Instruction Manual and Quick Reference Guide

• Rigid carrying case

Note: Save all packing material until you are sure that the instrument works correctly. Any

defective item must be returned in its original packing.

PRELIMINARY EXAMINATION

The HI96713 is an auto diagnostic portable microprocessor meter that benefits from

Hanna Instruments’ years of experience as a manufacturer of analytical instruments. It has the

advanced optical system based on a special Tungsten Lamp and a narrow band interference filter

that allows most accurate and repeatable readings. All instruments are factory calibrated and the

electronic and optical design minimizes the need of frequent calibration.

With the powerful CAL CheckTM validation function, you are able to validate good performance

of your instrument at any time. The validation procedure is extremely user friendly. Just use the

exclusive Hanna Instruments ready‑made, NIST traceable standards to verify the performance of

the instrument and recalibrate if necessary.

All instruments are splash proof and the lamp and filter units are protected from dust or dirt by

a transparent cup. This makes the instruments fulfill field applications. Display messages aid the

user in routine operation. The meter has an auto‑shut off feature that will turn off the instrument

after 10 minutes of non‑use in measurement mode or after 1 hour if left in calibration mode.

The meter uses an exclusive positive‑locking system to ensure that the cuvette is in the same

position every time it is placed into the measurement cell. It is designed to fit a cuvette with a

larger neck making it easier to add both sample and reagents. The cuvette is made from special

optical glass to obtain best results.

The HI96713 meter measures the phosphate content in water samples in the 0.00 to 2.50 mg/L

(ppm) range. The method is an adaptation of the ascorbic acid method.

The reagent is in powder form and is supplied in packets. The amount of reagent is precisely dosed

to ensure the maximum repeatability.

degree Celsius

degree Fahrenheit

milligrams per liter. mg/L is equivalent to ppm (parts per million)

milliliter

millivolt

°C:

°F:

mg/L:

mL:

mV:

GENERAL DESCRIPTION ABBREVIATIONS

Precision is how closely repeated measurements

agree with each other. Precision is usually

expressed as standard deviation (SD).

Accuracy is defined as the nearness of a test result

to the true value.

Although good precision suggests good accuracy,

precise results can be inaccurate. The figure

explains these definitions.

In a laboratory using a standard solution of

1.00 mg/L phosphate and a representative lot

of reagent, an operator obtained with a single

instrument a standard deviation of 0.03 mg/L.

SPECIFICATIONS

Range 0.00 to 2.50 mg/L

Resolution 0.01 mg/L

Accuracy

@25 °C (77 °F)

±0.04 mg/L ± 4% of reading

Light Source Tungsten lamp

Light Detector

Silicon Photocell with narrow band interference filter @610 nm

Method Adaptation of the ascorbic acid method. The reaction between phosphate and

the reagent causes a blue tint in the sample.

Environment 0 to 50 °C (32 to 122 °F)

max 95 % RH non‑condensing

Battery Type 9V (1 pc.)

Auto‑Shut off After 10’ of non‑use in measurement mode; after 1 hour of non‑use in

calibration mode; with last reading reminder

Dimensions 192 x 104 x 69 mm (7.6 x 4.1 x 2.7”)

Weight 320 g (11.3 oz.)

REQUIRED REAGENTS

Code Description Quantity/test

HI93713‑0 Powder Reagent 1 packet

PRECISION AND ACCURACY

Absorption of Light is a typical phenomenon of interaction between electromagnetic radiation and

matter. When a light beam crosses a substance, some of the radiation may be absorbed by atoms,

molecules or crystal lattices.

If pure absorption occurs, the fraction of light absorbed depends both on the optical path length

through the matter and on the physical‑chemical characteristics of the substance according to the

Lambert‑Beer Law:

‑log I/Io= ελc d

A = ελc d

Where:

‑log I/Io = Absorbance (A)

Io = intensity of incident light beam

I = intensity of light beam after absorption

ε

λ= molar extinction coefficient at wavelength λ

c = molar concentration of the substance

d = optical path through the substance

Therefore, the concentration “c” can be calculated from the absorbance of the substance as the

other factors are known.

Photometric chemical analysis is based on the possibility to develop an absorbing compound from a

specific chemical reaction between sample and reagents. Given that the absorption of a compound

strictly depends on the wavelength of the incident light beam, a narrow spectral bandwidth should

be selected as well as a proper central wavelength to optimize measurements.

The optical system of Hanna Instruments’ HI96 colorimeter is based on special tungsten lamp and

narrow‑band interference filters to guarantee both high performance and reliable results.

HI96 block diagram (optical layout)

PRINCIPLE OF OPERATION

1) GLP/ key

2) CAL Check key

3) ZERO/CFM key

4) READ /TIMER key

5) ON/OFF key

6) Liquid Crystal Display (LCD)

7) Cuvette alignment indicator

8) Cuvette holder

A microprocessor controlled special tungsten lamp emits radiation which is first optically conditioned

and beamed to the sample contained in the cuvette. The optical path is fixed by the diameter of

the cuvette. Then the light is spectrally filtered to a narrow spectral bandwidth, to obtain a light

beam of intensity Ioor I.

The photoelectric cell collects the radiation Ithat is not absorbed by the sample and converts it

into an electric current, producing a potential in the mV range.

The microprocessor uses this potential to convert the incoming value into the desired measuring

unit and to display it on the LCD.

The measurement process is carried out in two phases: first the meter is zeroed and then the actual

measurement is performed.

The cuvette has a very important role because it is an optical element and thus requires particular

attention. It is important that both, the measurement and the calibration (zeroing) cuvettes, are

optically identical to provide the same measurement conditions. Whenever possible use the same

cuvette for both. It is necessary that the surface of the cuvette is clean and not scratched. This to avoid

measurement interference due to unwanted reflection and absorption of light. It is recommended

not to touch the cuvette walls with hands.

Furthermore, in order to maintain the same conditions during the zeroing and the measuring phases,

it is necessary to close the cuvette to prevent any contamination.

INSTRUMENT DESCRIPTION

PRINCIPLE OF OPERATION

FUNCTIONAL DESCRIPTION

KEYPAD DESCRIPTION

• ON/OFF: to turn the meter on and off.

• ZERO/CFM: this is a bi‑functional key. Just press to zero the meter prior to measurement, or

confirm edited values. In calibration mode press to confirm factory calibration restore.

• READ /TIMER: this is a multi‑functional key. In measurement mode, press to make a

measurement, or press and hold for three seconds to start a pre‑programmed countdown prior

to measurement. In GLP mode press to view the next screen.

• CAL Check: this is a bi‑functional key. Just press to perform the validation of the meter, or

press and hold for three seconds to enter calibration mode.

•GLP/: this is a bi‑functional key. Just press to enter GLP mode. In calibration mode press

to edit the date and time.

OPERATING MODES

• Measurement mode: default operation mode, enables both validation and measurement.

• Calibration mode: may be entered by keeping CAL Check pressed for three seconds (the

“CAL” tag appears), it enables calibration of the instrument.

• GLP mode may be entered by pressing GLP/ (“GLP” appears), it enables consulting of

user calibration date or restore factory calibration.

DISPLAY ELEMENTS DESCRIPTION

1) The measuring scheme (lamp, cuvette, detector), appears during different phases of zero or

reading measurement

2) Error messages and warnings

3) The battery icon indicates the charge state of the battery

4) The hourglass appears when an internal check is in progress

5) Status messages

6) The chronometer appears when the reaction timer is running

7) The month, day and date icons appear when a date is displayed

8) Four digit main display

9) Measuring units

10) Four digit secondary display

FUNCTIONAL DESCRIPTION

The instrument shows clear messages when erroneous condition appears. Messages are also displayed

when the obtained values are outside expected range. The beeper is playing a beep on errors.

a) on zero reading

Light High: There is too much light to perform a measurement.

Please check the preparation of the zero cuvette.

Light Low: There is not enough light to perform a measurement.

Please check the preparation of the zero cuvette.

No Light: The instrument cannot adjust the light level. Please check

that the sample does not contain any debris.

Inverted cuvettes: The sample and the zero cuvette are inverted.

Zero: A zero reading was not taken. Follow the instructions of the

measurement procedure for zeroing the meter.

b) on sample reading

Under Range: A blinking “0.00” indicates that the sample absorbs

less light than the zero reference. Check the procedure and make sure

you use the same cuvette for reference (zero) and measurement.

ERRORS AND WARNINGS

Tabla de contenidos

Otros manuales de Instrumento de medición de Hanna Instruments

Hanna Instruments

Hanna Instruments HI 981410 Manual de usuario

Hanna Instruments

Hanna Instruments HI 93703-11 Manual de usuario

Hanna Instruments

Hanna Instruments HI 991401 Manual de usuario

Hanna Instruments

Hanna Instruments HALO 2 HI9810352 Manual de usuario

Hanna Instruments

Hanna Instruments GROLINE MONITOR HI981420 Manual de usuario

Hanna Instruments

Hanna Instruments HI 254 Manual de usuario

Hanna Instruments

Hanna Instruments HI 99141 Manual de usuario

Hanna Instruments

Hanna Instruments HI 98186 Manual de usuario

Hanna Instruments

Hanna Instruments HI98193 Manual de usuario

Hanna Instruments

Hanna Instruments HI 93703-11 Manual de usuario

Hanna Instruments

Hanna Instruments HI 8010 Manual de usuario

Hanna Instruments

Hanna Instruments HI 38018 Manual de usuario

Hanna Instruments

Hanna Instruments OHI 98140 Manual de usuario

Hanna Instruments

Hanna Instruments HI 2209 Manual de usuario

Hanna Instruments

Hanna Instruments HI 93739 Manual de usuario

Hanna Instruments

Hanna Instruments HI 93752 Manual de usuario

Hanna Instruments

Hanna Instruments HI 2210 Manual de usuario

Hanna Instruments

Hanna Instruments HA8424 Manual de usuario

Hanna Instruments

Hanna Instruments HI 95724C Manual de usuario

Hanna Instruments

Hanna Instruments DiST HI 98302 Manual de usuario

Hanna Instruments

Hanna Instruments HI 83141V Manual de usuario

Hanna Instruments

Hanna Instruments HI96738 Manual de usuario

Hanna Instruments

Hanna Instruments C 99 series Manual de usuario

Hanna Instruments

Hanna Instruments HI 83214 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario