Hanna Instruments HI 96753C Manual de usuario

Instruction Manual

HI 96753C

Chloride ISM

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

2 3

TABLE OF CONTENTS

PRELIMINARY EXAMINATION ..............................................................................................3

GENERAL DESCRIPTION .....................................................................................................4

ABBREVIATIONS ................................................................................................................4

SPECIFICATIONS .................................................................................................................5

PRECISION AND ACCURACY ................................................................................................5

PRINCIPLE OF OPERATION .................................................................................................6

FUNCTIONAL DESCRIPTION ................................................................................................7

ERRORS AND WARNINGS ..................................................................................................9

GENERAL TIPS FOR AN ACCURATE MEASUREMENT ...........................................................11

STARTUP .........................................................................................................................12

MEASUREMENT PROCEDURE ...........................................................................................12

VALIDATION PROCEDURE .................................................................................................15

CALIBRATION PROCEDURE ...............................................................................................17

GLP .................................................................................................................................20

BATTERY MANAGEMENT ..................................................................................................21

BATTERY REPLACEMENT ..................................................................................................22

ACCESSORIES ...................................................................................................................22

WARRANTY ......................................................................................................................23

Dear Customer,

Thank you for choosing a Hanna product. This manual will provide you with the necessary

information for the correct use of the instrument. Please read it carefully before using the meter.

All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner,

Hanna Instruments Inc., Woonsocket, Rhode Island, 02895 , USA.

PRELIMINARY EXAMINATION

Please examine this product carefully. Make sure that the instrument is not damaged. If any

damage occurred during shipment, please notify your Dealer.

Each HI 96753 Ion Selective Meter is supplied complete with:

• Two Sample Cuvettes and Caps

• CAL CHECK standard cuvettes

• 9V Battery

• Cloth for wiping cuvettes

• Instrument quality certificate

• Instruction Manual

• Rigid carrying case

Note:Save all packing material until you are sure that the instrument works correctly. Any

defective item must be returned in its original packing.

4 5

GENERAL DESCRIPTION

ABBREVIATIONS

SPECIFICATIONS

PRECISION AND ACCURACY

The HI 96753 is an auto diagnostic portable microprocessor meter that benefits from Hanna’s

years of experience as a manufacturer of analytical instruments. It has the advanced optical

system based on a special Light Emitting Diode (LED) and a narrow band interference filter that

allows most accurate and repeatable readings. All instruments are factory calibrated and the

electronic and optical design minimizes the need of frequent calibration.

With the powerful CAL CHECKTM validation function, you are able to validate good performance

of your instrument at any time. The validation procedure is extremely user friendly. Just use the

exclusive HANNA ready-made, NIST traceable standards to verify the performance of the

instrument and recalibrate if necessary.

All instruments are splash waterproof and the LED and filter units are protected from dust or dirt

by a transparent cup. This makes the instruments fulfill field applications. Display messages aid

the user in routine operation. The meter has an auto-shut off feature that will turn off the

instrument after 10 minutes of non use in

measurement mode

or after 1 hour if left in

calibration mode

The meter uses an exclusive positive-locking system to ensure that the cuvette is in the same

position every time it is placed into the measurement cell. It is designed to fit a cuvette with a

larger neck making it easier to add both sample and reagents. The cuvette is made from special

optical glass to obtain best results.

The HI 96753 meter measures the chloride (Cl–) content in water and wastewater samples in

the 0.0 to 20.0 mg/L (ppm) range. The method is an adaptation of the mercury(II) thiocyanate

method.

The reagents are in liquid form and are supplied in bottles. The amount of reagent is precisely

dosed to ensure the maximum repeatability.

degree Celsius

degree Fahrenheit

milligrams per liter. mg/L is equivalent to ppm (parts per million)

milliliter

millivolts

°C:

°F:

mg/L:

mL:

mV:

Range 0.0 to 20.0 mg/L

Resolution 0.1 mg/L

Accuracy ±0.5 mg/L ±6% of reading @ 25°C

Typical EMC Deviation ±0.1 mg/L

Light Source Light Emitting Diode

Light Detector Silicon Photocell with narrow band interference filter @ 466nm

Method Adaptation of the mercury(II) thiocyanate method. The chloride ion

displaces thiocyanate ion from mercury(II). The iron(III) present

forms with thiocyanate an orange colored complex. The intensity of

color is proportional to the chloride ion concentration.

Environment 0 to 50°C (32 to 122°F); max 95% RH non-condensing

Battery Type 1 x 9 volt

Auto-Shut off After 10' of non-use in

measurement mode

;

after 1 hour of non-use in

calibration mode

;

with last reading reminder.

Dimensions 192 x 104 x 69 mm (7.6 x 4.1 x 2.7”)

Weight 260 g (12.7 oz.).

REQUIRED REAGENTS

Code Description Quantity/test

HI 93753A-0 Displacing Reagent 1.0 mL

HI 93753B-0 Complexing Reagent 1.0 mL

PrecisionPrecision

Precision is how closely repeated measurements

agree with each other. Precision is usually

expressed as standard deviation (SD).

AccuracyAccuracy

Accuracy is defined as the nearness of a test

result to the true value.

Although good precision suggests good accuracy,

precise results can be inaccurate. The figure

explains these definitions.

In a laboratory using a standard solution of

10.0 mg/L chloride and a representative lot of

reagent, an operator obtained with a single

instrument a standard deviation of 0.3 mg/L.

6 7

1) GLP/ key

2) CAL CHECK key

3) ZERO/CFM key

4) READ/ /TIMER key

5) ON/OFF key

6) Liquid Crystal Display (LCD)

7) Cuvette alignment indicator

8) Cuvette holder

PRINCIPLE OF OPERATION

FUNCTIONAL DESCRIPTION

Absorption of Light is a typical phenomenon of interaction between electromagnetic radiation and

matter. When a light beam crosses a substance, some of the radiation may be absorbed by

atoms, molecules or crystal lattices.

If pure absorption occurs, the fraction of light absorbed depends both on the optical path length

through the matter and on the physical-chemical characteristics of the substance according to the

Lambert-Beer Law:

-log I/Io = ελ c d

A = ελ c d

Where:

-log I/Io=Absorbance (A)

Io=intensity of incident light beam

I=intensity of light beam after absorption

ελ=molar extinction coefficient at wavelength λ

c=molar concentration of the substance

d=optical path through the substance

Therefore, the concentration "c" can be calculated from the absorbance of the substance as the

other factors are known.

Photometric chemical analysis is based on the possibility to develop an absorbing compound

from a specific chemical reaction between sample and reagents. Given that the absorption of a

compound strictly depends on the wavelength of the incident light beam, a narrow spectral

bandwidth should be selected as well as a proper central wavelength to optimize measurements.

The optical system of Hanna's HI 96753 colorimeter is based on special LED and narrow-band

interference filters to guarantee both high performance and reliable results.

HI 96753 block diagram (optical layout)

A microprocessor controlled special LED emits radiation which is first optically conditioned and

beamed to the sample contained in the cuvette. The optical path is fixed by the diameter of the

cuvette. Then the light is spectrally filtered to a narrow spectral bandwidth, to obtain a light

beam of intensity Ioor I.

The photoelectric cell collects the radiation Ithat is not absorbed by the sample and converts

it into an electric current, producing a potential in the mV range.

The microprocessor uses this potential to convert the incoming value into the desired measuring

unit and to display it on the LCD.

The measurement process is carried out in two phases: first the meter is zeroed and then the

actual measurement is performed.

The cuvette has a very important role because it is an optical element and thus requires

particular attention. It is important that both, the measurement and the calibration (zeroing)

cuvettes, are optically identical to provide the same measurement conditions. Whenever possible

use the same cuvette for both. It is necessary that the surface of the cuvette is clean and not

scratched. This to avoid measurement interference due to unwanted reflection and absorption of

light. It is recommended not to touch the cuvette walls with hands.

Furthermore, in order to maintain the same conditions during the zeroing and the measuring

phases, it is necessary to close the cuvette to prevent any contamination.

INSTRUMENT DESCRIPTION

8 9

ERRORS AND WARNINGS

KEYPAD DESCRIPTION

•ON/OFF: to turn the meter on and off.

•ZERO/CFM: to zero the meter prior to measurement, to confirm edited values or to confirm

factory calibration restore.

•READ/ /TIMER: this is a multi-functional key. In

measurement mode

, press to make a

measurement, or press and hold for three seconds to start a pre-programmed countdown prior

to measurement. In

GLP mode

press to view the next screen.

•CAL CHECK: this is a bi-functional key. Just press to perform the validation of the meter, or

press and hold for three seconds to enter

calibration mode

•GLP/: this is a bi-functional key. Just press to enter

GLP mode

. In

calibration mode

press

to edit the date and time.

OPERATING MODES

•

Measurement mode:

default operation mode, enables both validation and measurement.

•

Calibration mode:

may be entered

by keeping CAL CHECK pressed for three seconds (the

“CAL” tag appears), it enables calibration of the instrument.

•

GLP mode

may be entered by pressing GLP/(“GLP” appears), it enables consulting of

user calibration date or restore factory calibration.

DISPLAY ELEMENTS DESCRIPTION

1) The measuring scheme (lamp, cuvette, detector), appears during different phases of zero or

reading measurement

2) Error messages and warnings

3) The battery icon shows the charging level of the battery

4) The hourglass appears when an internal checking is in progress

5) Status messages

6) The chronometer appears when the reaction timer is running

7) The month, day and date icons appear when a date is displayed

8) Four digit main display

9) Measuring units

10) Four digit secondary display

The instrument shows clear messages when erroneous condition appears. Messages are also displayed

when the obtained values are outside expected range. The beeper is playing a beep on errors.

a) on zero reading

Light High: There is too much light to perform a measurement.

Please check the preparation of the zero cuvette.

Light Low: There is not enough light to perform a measurement.

Please check the preparation of the zero cuvette.

No Light:The instrument cannot adjust the light level. Please

check that the sample does not contain any debris.

Inverted cuvettes: The sample and the zero cuvette are inverted.

Zero: A zero reading was not taken. Follow the instructions of

the measurement procedure for zeroing the meter.

b) on sample reading

10 11

The instructions listed below should be carefully followed during testing to ensure best accuracy.

•Color or suspended matter in large amounts may cause

interference, therefore these should be removed by

treatment with active carbon and by prior filtration.

•For a correct filling of the cuvette: the liquid in the

cuvette forms a concavity on the top; the bottom of this

concavity must be at the same level of the 10 mL mark.

•In order to measure exactly 0.5 mL of reagent with the 1 mL syringe:

(a) push the plunger completely into the syringe and insert the tip into the solution.

(b) pull the plunger up until the lower edge of the seal is exactly on the 0.0 mL mark.

hanging on the tip of the syringe, if so eliminate them. Then, keeping the syringe in

vertical position above the cuvette, push the plunger down into the syringe until the lower

edge of the seal is exactly on the 0.5 mL mark. Now the exact amount of 0.5 mL has

been added to the cuvette, even if the tip still contains some solution.

GENERAL TIPS FOR AN ACCURATE MEASUREMENT

Under Range: A blinking “0.0” indicates that the sample

absorbs less light than the zero reference. Check the procedure

and make sure you use the same cuvette for reference (zero) and

measurement.

Over Range: A flashing value of the maximum concentration

indicates an over range condition. The concentration of the

sample is beyond the programmed range: dilute the sample and

re-run the test.

c) during calibration procedure

Standard Low: The standard reading is less than expected.

Standard High: The standard reading is higher than expected.

Cap error: Appears when external light enters in the analysis

cell. Assure that the cuvette cap is present.

Cooling lamp: The instrument waits for the lamp to cool down.

d) other errors and warnings

Battery low: The battery must be replaced soon.

Dead battery: This indicates that the battery is dead and must

be replaced. Once this indication is displayed, the meter will

lock up. Change the battery and restart the meter.

(c)(a) (b)

12 13

•It is important that the sample does not contain any debris. This would corrupt the reading.

•Each time the cuvette is used, the cap must be tightened to the same degree.

•Whenever the cuvette is placed into the measurement cell, it must be

dry outside, and completely free of fingerprints, oil or dirt. Wipe it

thoroughly with HI 731318 or a lint-free cloth prior to insertion.

•Shaking the cuvette can generate bubbles in the sample, causing

higher readings. To obtain accurate measurements, remove such bubbles

by swirling or by gently tapping the cuvette.

•Do not let the reacted sample stand too long after reagent is added, or accuracy will be lost.

•It is possible to take multiple readings in a row, but it is recommended to take a new zero

reading for each sample and to use the same cuvette for zeroing and measurement.

•After the reading it is important to discard immediately the sample, otherwise the glass

might become permanently stained.

•All the reaction times reported in this manual are referred to 20°C (68°F). As a general rule

of thumb, they should be doubled at 10°C (50°F) and halved at 30°C (86°F).

•In order to maximize accuracy, prior to a measurement follow the validation procedure to

be sure that the instrument is properly calibrated. If necessary, calibrate the instrument.

MEASUREMENT PROCEDURE

STARTUP

Prepare the instrument for measurement as follows:

•Unpack the instrument by removing the dust protection sleeve from the instrument cuvette

holder.

•Place the battery in the instrument as described in the “BATTERY REPLACEMENT” chapter.

•Place the instrument on a flat table.

•Do not place the instrument under direct sun light.

To compensate the meter for the sample turbidity or color, the measurement takes place in two

phases. First, the meter is zeroed using the unreacted sample. After the reagents are added the

reacted sample is measured.

•When the beeper sounds briefly and the LCD

displays dashes, the meter is ready. The blinking

“ZERO” indicates that the instrument needs to

be zeroed first.

•Fill one cuvette (#1) with 10 mL of distilled

water (up to the mark).

•Fill another cuvette (#2) with 10 mL of

sample (up to the mark)

Note: for low chloride ions concentration, rinse

the cuvette a couple of times with sample

before filling it with 10 mL of sample (up to the

mark).

Note: for most accurate results, use two gradu-

ated pipettes to deliver exactly 10 mL of distilled water and 10 mL of sample to the cuvettes.

•Using the 1 mL syringe, add 0.5 mL of HI 93753A-0 Displacing Reagent to each cuvette.

•Replace the caps and mix each cuvette by turning the cuvette upside down for approximately

30 seconds.

•Turn the meter on by pressing ON/OFF.

The display briefly shows all tags on.

14 15

•Remove the caps and use the second 1 mL

syringe to add 0.5 mL of HI 93753B-0

Complexing Reagent to each cuvette.

•Replace the caps and mix each cuvette

by turning the cuvette upside down for

approximately 30 seconds.

•Place the cuvette with the reacted distilled

water (#1) into the cuvette holder and

ensure that the notch on the cap is

positioned securely into the groove.

•Press READ/ /TIMER.The display will

show the countdown prior to zeroing. The

beeper is playing a beep at the end of

countdown period.

Alternatively, wait for 2minutes then just

press ZERO/CFM.

In both cases, the lamp, cuvette and

detector icons will appear on the display,

depending on the zeroing phase.

•After a few seconds, the display will

show “-0.0-”. The meter is now zeroed

and ready for measurement.

•Remove the cuvette.

•Place the other cuvette with the reacted

sample (#2) into the cuvette holder

and ensure that the notch on the cap is

positioned securely into the groove.

# 1

•Press READ/ /TIMER. The lamp, cuvette

and detector icons will appear on the

display, depending on the measurement

phase.

•At the end of measurement, the instrument

directly displays concentration in mg/L of

chloride on the LCD.

INTERFERENCES

The pH of sample after addition of reagents should be about 2. For alkaline samples, neutralize

before adding reagents.

Intensely colored samples will cause interference, therefore they should be adequately treated before

performing the test. Suspended matter in large amounts should be removed by prior filtration.

# 2

VALIDATION PROCEDURE

Use the validation procedure to ensure that the instrument is properly calibrated.

Warning: Do not validate the instrument with any standard solutions other than the HANNA CAL

CHECKTM Standards, otherwise erroneous results will be obtained.

•Turn the meter on by pressing ON/OFF.

•Place the CAL CHECKTM Standard

HI 96753-11 Cuvette A into the cuvette

holder and ensure that the notch on the

cap is positioned securely into the groove.

•When the beeper sounds briefly and the

LCD displays dashes, the meter is ready.

16 17

CALIBRATION PROCEDURE

Note: It is possible to interrupt calibration procedure at any time by pressing CAL CHECK or

ON/OFF keys.

Warning:Do not calibrate the instrument with standard solutions other than the HANNA CAL

CHECKTM Standards, otherwise erroneous results will be obtained.

•Turn the meter on by pressing ON/OFF.

•When the beeper sounds briefly and the

LCD displays dashes, the meter is ready.

•Press and hold CAL CHECK for three

seconds to enter

calibration mode

. The

display will show “CAL” during

calibration procedure. The blinking

“ZERO” asks for instrument zeroing.

•Place the CAL CHECKTM Standard

HI 96753-11 Cuvette A into the cuvette

holder and ensure that the notch on the

cap is positioned securely into the groove.

•Press ZERO/CFM and the lamp, cuvette

and detector icons will appear on the

display, depending on the measurement

phase.

•Press ZERO/CFM and the lamp, cuvette

and detector icons will appear on the

display, depending on the measurement

phase.

•After a few seconds, the display will

show “-0.0-”. The meter is now zeroed

and ready for validation.

•Remove the cuvette.

•Place the CAL CHECKTM Standard

HI 96753-11 Cuvette B into the cuvette

holder and ensure that the notch on the

cap is positioned securely into the groove.

•Press CAL CHECK and the lamp, cuvette

and detector icons together with “CAL

CHECK” will appear on the display,

depending on the measurement phase.

•At the end of the measurement the display

will show the validation standard value.

The reading should be within specifications as reported in the CAL CHECKTM Standard

Certificate. If the value is found out of the specifications, please check that the cuvettes are free

of fingerprints, oil or dirt and repeat validation. If results are still found out of specifications,

then recalibrate the instrument.

18 19

•Press GLP/ to edit the desired year

(2000-2099). If the key is kept pressed,

the year number is automatically

increased.

•Press GLP/ to edit the desired day

(01-31). If the key is kept pressed, the

day number is automatically increased.

Note: It is possible to change the editing

from day to year and to month by pressing

READ/ /TIMER.

•When the correct year has been set, press

ZERO/CFM or READ/ /TIMER to

confirm. Now the display will show the

month blinking.

•Press GLP/ to edit the desired month

(01-12). If the key is kept pressed, the

month number is automatically increased.

•When the correct month has been set,

press ZERO/CFM or READ/ /TIMER

to confirm. Now the display will show

the day blinking.

•Press ZERO/CFM to save the calibration

date.

•The instrument displays “Stor” for one

second and the calibration is saved.

DATE INPUT

•After a few seconds the display will show

“-0.0-”. The meter is now zeroed and ready

for calibration. The blinking “READ” asks for

reading calibration standard.

•Remove the cuvette.

•Place the CAL CHECKTM Standard HI 96753-11

Cuvette B into the cuvette holder and ensure

that the notch on the cap is positioned securely

into the groove.

•Press READ/ /TIMER and the lamp, cuvette

and detector icons will appear on the display,

depending on the measurement phase.

•After measurement the instrument will show for

three seconds the CAL CHECKTM Standard value.

Note: If the display shows “STD HIGH”, the

standard value was too high. If the display

shows “STD LOW”, the standard value was

too low. Verify that both CAL CHECKTM

Standards HI 96753-11 Cuvettes, A and B are

free from fingerprints or dirt and that they are

inserted correctly.

Then the date of the last calibration (e.g.:

”01.08.2008”) appears on the display, or

“01.01.2008” if the factory calibration was

selected before. In both cases the year number

is blinking, ready for date input.

Tabla de contenidos

Otros manuales de Instrumento de medición de Hanna Instruments

Hanna Instruments

Hanna Instruments HI 9813-5 Manual de usuario

Hanna Instruments

Hanna Instruments HI 5421 Manual de usuario

Hanna Instruments

Hanna Instruments HI 95724C Manual de usuario

Hanna Instruments

Hanna Instruments HI98192 Manual de usuario

Hanna Instruments

Hanna Instruments HI 720 Manual de usuario

Hanna Instruments

Hanna Instruments HI97727 Manual de usuario

Hanna Instruments

Hanna Instruments HI 99181 Manual de usuario

Hanna Instruments

Hanna Instruments HI97722 Manual de usuario

Hanna Instruments

Hanna Instruments GROLINE MONITOR HI981420 Manual de usuario

Hanna Instruments

Hanna Instruments HI 250 Manual de usuario

Hanna Instruments

Hanna Instruments HI 83140 Manual de usuario

Hanna Instruments

Hanna Instruments HI 762 Manual de usuario

Hanna Instruments

Hanna Instruments HI723 Manual de usuario

Hanna Instruments

Hanna Instruments HI97738 Manual de usuario

Hanna Instruments

Hanna Instruments HI 8064 Manual de usuario

Hanna Instruments

Hanna Instruments HI97712 Manual de usuario

Hanna Instruments

Hanna Instruments HI739 Manual de usuario

Hanna Instruments

Hanna Instruments HI9811-51 Manual de usuario

Hanna Instruments

Hanna Instruments HI96718C Manual de usuario

Hanna Instruments

Hanna Instruments HI 720 Manual de usuario

Hanna Instruments

Hanna Instruments HI 2222 Manual de usuario

Hanna Instruments

Hanna Instruments HI 98127 Manual de usuario

Hanna Instruments

Hanna Instruments HI774 Manual de usuario

Hanna Instruments

Hanna Instruments HI 4521 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario