Hanna Instruments HI 747 Manual de usuario

Copper Low Range Preliminary examination:

Please examine this product carefully. Make sure that the instrument is not damaged. If

any damage occurred during shipment, please notify your Dealer.

Each HI 747 meter is supplied complete with:

• Two Sample Cuvettes and Caps

• Reagents for 6 tests

• 1 x 1.5V AAA Battery

• Instruction Manual

HI 747

Functional description:

Errors and warnings:

Light High: There is too much light to perform a measurement.

Please check the preparation of the zero cuvette.

Light Low: There is not enough light to perform a measurement.

Please check the preparation of the zero cuvette.

Inverted Cuvettes: The sample and the zero cuvette are inverted.

Under Range: A blinking “0” indicates that the sample absorbs less

light than the zero reference. Check the procedure and make sure you

use the same cuvette for reference (zero) and measurement.

Over Range: A flashing value of the maximum concentration indicates

the reading is over range. Dilute the sample and re-run the test.

Battery Low: The battery must be replaced soon.

Dead Battery: This indicates that the battery is dead and must be

replaced. Once this indication is displayed, normal operation of the

instrument will be interrupted. Change the battery and restart the

meter.

1. Dust cover.

2. Cuvette with cap.

3. Cuvette holder.

4. Liquid Crystal Display.

5. Button.

For more details about spare parts and accessories

see “Accessories”.

Dear Customer,

Thank you for choosing a Hanna Instruments Product.

Please read this instruction manual carefully before using the instrument. If you need

additional technical information, do not hesitate to e-mail us at [email protected]

or view our worldwide contact list at www.hannainst.com.

www.hannainst.com

Technical specifications:

Range 0 to 999 ppb

Resolution 1 ppb

Accuracy ±10 ppb ±5% of reading @ 25 °C / 77 °F

Light Source Light Emitting Diode @ 575 nm

Light Detector Silicon Photocell

Method Adaptation of the EPA method. The reaction between

copper and the bicinchoninate reagent causes a purple

tint in the sample.

Environment 0 to 50 °C (32 to 122 °F);

max 95% RH non-condensing

Battery Type 1 x 1.5V AAA

Auto-Shut off After 10 minutes of non-use

Dimensions 86 x 61 x 37.5 mm (3.38 x 2.4 x 1.5”)

Weight 64 g (2.25 oz.)

[email protected]

www.ponpe.com

•Turn the meter on by pressing the button.

All segments will be displayed. When the

display shows “Add”, “C.1” with “Press”

blinking, the meter is ready.

•Fill the cuvette with 10 mL of unreacted

sample and replace the cap. Place the cuvette

into the meter and close the meter’s cap.

•Press the button. When the display shows

“Add”, “C.2” with “Press” blinking the

meter is zeroed.

•Remove the cuvette from the meter and unscrew

the cap. Add the content of one packet of

HI 747-0 reagent. Replace the cap and shake

until completely dissolved. Wait approximately

30 seconds for air bubbles to dissipate.

•Place the cuvette back into the meter and

close the meter’s cap. Press the button.

•The instrument directly displays the

concentration of copper in ppb. The meter

automatically turns off after 10 minutes.

10 mL

REAGENT SETS

HI 747-25 Reagent for 25 Copper Low Range Tests

OTHER ACCESSORIES

HI 747-11 Copper LR Certified Standard Kit

HI 731318 Cloth for wiping cuvettes (4 pcs.)

HI 731321 Glass cuvettes (4 pcs.)

HI 731225 Black cuvette cap for checker HC (4 pcs.)

HI 740028 1.5V AAA batteries (4 pcs.)

HI 93703-50 Cuvette cleaning solution (230 mL)

Recommendations for Users

www.hannainst.com

Hanna Instruments reserves the right to modify the design, construction or

appearance of its products without advance notice.

Battery management

IST747 04/15

Measurement procedure: Accessories:Tips for an accurate measurement

For additional information, contact your

dealer or the nearest

Hanna Customer Service Center.

To find a Hanna Office in your area,

visit our web site:

•It is important that the sample does not contain any debris.

•Whenever the cuvette is placed into the measurement cell, it must be dry

outside, and completely free of fingerprints, oil and dirt. Wipe it thoroughly with

HI 731318 or a lint-free cloth prior to insertion.

•Shaking the cuvette can generate bubbles, causing higher readings. To obtain

accurate measurements, remove bubbles by swirling or by gently tapping the

cuvette.

•Do not let the reacted sample stand for too long after reagent is added, as

accuracy will be affected.

•After the reading it is important to immediately discard the sample, otherwise

the glass might become permanently stained.

To save the battery, the instrument shuts down after 10 minutes of non-use.

One fresh battery lasts for a minimum of 5000 measurements. When the battery is dead

the instrument will display “bAd” then ”bAt” for 1 second and then turns off.

To restart the instrument, the battery must be replaced with a new one.

To replace the instrument’s battery:

•Turn the instrument off by holding the button until the meter shuts off.

•Turn the instrument upside down and remove the battery cover with a screwdriver.

•Remove the battery from its location and replace it with a new one, inserting the

negative end first.

•Insert the battery cover and replace the screw with a screwdriver.

Before using this product, make sure that it is entirely suitable for your specific application and for the

environment in which it is used.

Operation of this instrument may cause unacceptable interferences to other electronic equipment, thus

requiring the operator to take all necessary steps to correct interferences.

Any variation introduced by the user to the supplied equipment may degrade the instrument’s EMC

performance.

To avoid damage or burns, do not put the instrument in microwave oven. For the safety of you and the

instrument do not use or store the instrument in hazardous environments.

[email protected]

www.ponpe.com

Otros manuales de Instrumento de medición de Hanna Instruments

Hanna Instruments

Hanna Instruments BL 7916 Manual de usuario

Hanna Instruments

Hanna Instruments HI 91610 Manual de usuario

Hanna Instruments

Hanna Instruments HI981520 Manual de usuario

Hanna Instruments

Hanna Instruments HI 991301 Manual de usuario

Hanna Instruments

Hanna Instruments HI 93729 Manual de usuario

Hanna Instruments

Hanna Instruments HI 718 Manual de usuario

Hanna Instruments

Hanna Instruments HI 720 Manual de usuario

Hanna Instruments

Hanna Instruments HI84502 Manual de usuario

Hanna Instruments

Hanna Instruments HI 758 Manual de usuario

Hanna Instruments

Hanna Instruments HI 84532 Manual de usuario

Hanna Instruments

Hanna Instruments HI99151 Manual de usuario

Hanna Instruments

Hanna Instruments HI97729 Manual de usuario

Hanna Instruments

Hanna Instruments Champ HI 98106 Manual de usuario

Hanna Instruments

Hanna Instruments HI6421 Manual de usuario

Hanna Instruments

Hanna Instruments HI5321 Manual de usuario

Hanna Instruments

Hanna Instruments HI8931A Manual de usuario

Hanna Instruments

Hanna Instruments HI 746 Manual de usuario

Hanna Instruments

Hanna Instruments HI 96770 Manual de usuario

Hanna Instruments

Hanna Instruments HI 99131 Manual de usuario

Hanna Instruments

Hanna Instruments HI 83141 Manual de usuario

Hanna Instruments

Hanna Instruments HI 96107 Manual de usuario

Hanna Instruments

Hanna Instruments HI6321 Manual de usuario

Hanna Instruments

Hanna Instruments HI-96730 Manual de usuario

Hanna Instruments

Hanna Instruments HI 84429 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario