Hanna Instruments 96728 Manual de usuario
1
Instruction Manual
HI 96728
Nitrate ISM
2
TABLE OF CONTENTS
PRELIMINARY EXAMINATION ................................................................................................ 3
GENERAL DESCRIPTION ....................................................................................................... 4
ABBREVIATIONS .................................................................................................................. 4
SPECIFICATIONS ................................................................................................................... 5
PRECISION AND ACCURACY .................................................................................................. 5
PRINCIPLE OF OPERATION ................................................................................................... 6
FUNCTIONAL DESCRIPTION .................................................................................................. 7
ERRORS AND WARNINGS .................................................................................................... 9
GENERAL TIPS FOR AN ACCURATE MEASUREMENT ............................................................. 11
STARTUP ........................................................................................................................... 12
MEASUREMENT PROCEDURE ............................................................................................. 12
VALIDATION PROCEDURE ................................................................................................... 15
CALIBRATION PROCEDURE ................................................................................................. 17
GLP ................................................................................................................................... 20
BATTERY MANAGEMENT .................................................................................................... 21
BATTERY REPLACEMENT .................................................................................................... 22
ACCESSORIES ..................................................................................................................... 22
WARRANTY........................................................................................................................ 23
Dear Customer,
Thank you for choosing a Hanna product. This manual will provide you with the necessary
information for the correct use of the instrument. Please read it carefully before using the meter. If
All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner,
Hanna Instruments Inc., Woonsocket, Rhode Island, 02895 , USA.
3
PRELIMINARY EXAMINATION
Please examine this product carefully. Make sure that the instrument is not damaged. If any
damage occurred during shipment, please notify your Dealer.
Each HI 96728 Ion Selective Meter is supplied complete with:
• Two Sample Cuvettes and Caps
• 9V Battery
• Instrument quality certificate
• Instruction Manual
Note:Save all packing material until you are sure that the instrument works correctly. Any
defective item must be returned in its original packing.
4
GENERAL DESCRIPTION
ABBREVIATIONS
The HI 96728 is an auto diagnostic portable microprocessor meter that benefits from Hanna’s
years of experience as a manufacturer of analytical instruments. It has the advanced optical
system based on a special Tungsten Lamp and a narrow band interference filter that allows most
accurate and repeatable readings. All instruments are factory calibrated and the electronic and
optical design minimizes the need of frequent calibration.
With the powerful CAL CHECKTM validation function, you are able to validate good performance
of your instrument at any time. The validation procedure is extremely user friendly. Just use the
exclusive HANNA ready-made, NIST traceable standards to verify the performance of the
instrument and recalibrate if necessary.
All instruments are splash waterproof and the lamp and filter units are protected from dust or dirt
by a transparent cup. This makes the instruments fulfill field applications. Display messages aid
the user in routine operation. The meter has an auto-shut off feature that will turn off the
instrument after 10 minutes of non use in
measurement mode
or after 1 hour if left in
calibration mode
.
The meter uses an exclusive positive-locking system to ensure that the cuvette is in the same
position every time it is placed into the measurement cell. It is designed to fit a cuvette with a
larger neck making it easier to add both sample and reagents. The cuvette is made from special
optical glass to obtain best results.
The HI 96728 meter measures the nitrate-nitrogen content in water samples in the 0.0 to 30.0 mg/
L(ppm) range. The method is an adaptation of the cadmium reduction method.
The reagent is in powder form and is supplied in packets. The amount of reagent is precisely
dosed to ensure the maximum repeatability.
degree Celsius
degree Fahrenheit
micrograms per liter. mg/L is equivalent to ppm (parts per million)
milliliter
millivolts
°C:
°F:
mg/L:
mL:
mV:
5
SPECIFICATIONS
PRECISION AND ACCURACY
Range 0.0 to 30.0 mg/L
Resolution 0.1 mg/L
Accuracy ±0.5 mg/L ±10% of reading@ 25°C
Typical EMC Deviation ±0.1 mg/L
Light Source Tungsten lamp
Light Detector Silicon Photocell with narrow band interference filter @ 525 nm
Method Adaptation of the cadmium reduction method. The reaction between nitrate-
nitrogen and the reagent causes an amber tint in the sample.
Battery Type 1 x 9 volt
Auto-Shut off After 10' of non-use in
measurement mode
;
after 1 hour of non-use in
calibration mode
;
with last reading reminder.
Dimensions 192 x 104 x 69 mm (7.6 x 4.1 x 2.7 ”)
Weight 360 g (12.7 oz.).
REQUIRED REAGENTS
Code Description Quantity/test
HI93728-0 Powder Reagent 1 packet
Precision is how closely repeated measurements
agree with each other. Precision is usually
expressed as standard deviation (SD).
Accuracy is defined as the nearness of a test
result to the true value.
Although good precision suggests good accuracy,
precise results can be inaccurate. The figure
explains these definitions.
In a laboratory using a standard solution of
10.0 mg/L nitrate and a representative lot of
reagent, an operator obtained with a single
instrument a standard deviation of 0.3 mg/L.
6
PRINCIPLE OF OPERATION
Absorption of Light is a typical phenomenon of interaction between electromagnetic radiation and
matter. When a light beam crosses a substance, some of the radiation may be absorbed by
atoms, molecules or crystal lattices.
If pure absorption occurs, the fraction of light absorbed depends both on the optical path length
through the matter and on the physical-chemical characteristics of the substance according to the
Lambert-Beer Law:
-log I/Io= ελc d
or
A = ελc d
Where:
-log I/Io=Absorbance (A)
Io=intensity of incident light beam
I=intensity of light beam after absorption
ελ=molar extinction coefficient at wavelength λ
c=molar concentration of the substance
d=optical path through the substance
Therefore, the concentration "c" can be calculated from the absorbance of the substance as the
other factors are known.
Photometric chemical analysis is based on the possibility to develop an absorbing compound
from a specific chemical reaction between sample and reagents. Given that the absorption of a
compound strictly depends on the wavelength of the incident light beam, a narrow spectral
bandwidth should be selected as well as a proper central wavelength to optimize measurements.
The optical system of Hanna's HI 96 colorimeter is based on special tungsten lamp and narrow-band
interference filters to guarantee both high performance and reliable results.
HI 96 block diagram (optical layout)
7
1) GLP/ key
2) CAL CHECK key
3) ZERO/CFM key
4) READ/ /TIMER key
5) ON/OFF key
6) Liquid Crystal Display (LCD)
7) Cuvette alignment indicator
8) Cuvette holder
FUNCTIONAL DESCRIPTION
A microprocessor controlled special tungsten lamp emits radiation which is first optically
conditioned and beamed to the sample contained in the cuvette. The optical path is fixed by the
diameter of the cuvette. Then the light is spectrally filtered to a narrow spectral bandwidth, to
obtain a light beam of intensity Ioor I.
The photoelectric cell collects the radiation Ithat is not absorbed by the sample and converts
it into an electric current, producing a potential in the mV range.
The microprocessor uses this potential to convert the incoming value into the desired measuring
unit and to display it on the LCD.
The measurement process is carried out in two phases: first the meter is zeroed and then the
actual measurement is performed.
The cuvette has a very important role because it is an optical element and thus requires
particular attention. It is important that both, the measurement and the calibration (zeroing)
cuvettes, are optically identical to provide the same measurement conditions. Whenever possible
use the same cuvette for both. It is necessary that the surface of the cuvette is clean and not
scratched. This to avoid measurement interference due to unwanted reflection and absorption of
light. It is recommended not to touch the cuvette walls with hands.
Furthermore, in order to maintain the same conditions during the zeroing and the measuring
phases, it is necessary to close the cuvette to prevent any contamination.
INSTRUMENT DESCRIPTION
8
10
8
5
2
9
7
3
4
6
1
KEYPAD DESCRIPTION
•ON/OFF: to turn the meter on and off.
•ZERO/CFM: this is a bi-functional key. Just press to zero the meter prior to measurement,
or confirm edited values. In
calibration mode
press to confirm factory calibration restore.
•READ/ /TIMER: this is a multi-functional key. In
measurement mode
, press to make a
measurement, or press and hold for three seconds to start a pre-programmed countdown prior
to measurement. In
GLP mode
press to view the next screen.
•CAL CHECK: this is a bi-functional key. Just press to perform the validation of the meter, or
press and hold for three seconds to enter
calibration mode
.
•GLP/: this is a bi-functional key. Just press to enter
GLP mode
. In
calibration mode
press
to edit the date and time.
OPERATING MODES
•
Measurement mode:
default operation mode, enables both validation and measurement.
•
Calibration mode:
may be entered
by keeping CAL CHECK pressed for three seconds (the
“CAL” tag appears), it enables calibration of the instrument.
•
GLP mode
may be entered by pressing GLP/ (“GLP” appears), it enables consulting of
user calibration date or restore factory calibration.
DISPLAY ELEMENTS DESCRIPTION
1) The measuring scheme (lamp, cuvette, detector), appears during different phases of zero or
reading measurement
2) Error messages and warnings
3) The battery icon indicates the charge state of the battery
4) The hourglass appears when an internal check is in progress
5) Status messages
6) The chronometer appears when the reaction timer is running
7) The month, day and date icons appear when a date is displayed
8) Four digit main display
9) Measuring units
10) Four digit secondary display
9
ERRORS AND WARNINGS
The instrument shows clear messages when erroneous condition appears. Messages are also
displayed when the obtained values are outside expected range. The beeper is playing a beep on
errors.
a) on zero reading
Light High: There is too much light to perform a measurement.
Please check the preparation of the zero cuvette.
Light Low: There is not enough light to perform a measurement.
Please check the preparation of the zero cuvette.
No Light: The instrument cannot adjust the light level. Please
check that the sample does not contain any debris.
Inverted cuvettes: The sample and the zero cuvette are inverted.
Zero: A zero reading was not taken. Follow the instructions of
the measurement procedure for zeroing the meter.
b) on sample reading
Under Range: A blinking “0.0” indicates that the sample
absorbs less light than the zero reference. Check the procedure
and make sure you use the same cuvette for reference (zero) and
measurement.
10
Over Range: A flashing value of the maximum concentration
indicates an over range condition. The concentration of the
sample is beyond the programmed range: dilute the sample and
re-run the test.
c) during calibration procedure
Standard Low: The standard reading is less than expected.
Standard High: The standard reading is higher than expected.
Cap error: Appears when external light enters in the analysis
cell. Assure that the cuvette cap is present.
Cooling lamp: The instrument waits for the lamp to cool down.
d) other errors and warnings
Battery low: The battery must be replaced soon.
Dead battery: This indicates that the battery is dead and must
be replaced. Once this indication is displayed, normal operation
of the instrument will be interrupted. Change the battery and
restart the meter.
Tabla de contenidos
Otros manuales de Instrumento de medición de Hanna Instruments
Hanna Instruments
Hanna Instruments HI 4111 Manual de usuario
Hanna Instruments
Hanna Instruments HI8424NEW Manual de usuario
Hanna Instruments
Hanna Instruments HI 98713 Manual de usuario
Hanna Instruments
Hanna Instruments HALO 2 HI9810352 Manual de usuario
Hanna Instruments
Hanna Instruments HI 4102 Manual de usuario
Hanna Instruments
Hanna Instruments HI96719C Manual de usuario
Hanna Instruments
Hanna Instruments HI 98186 Manual de usuario
Hanna Instruments
Hanna Instruments HI 93754G-25 MR Manual de usuario
Hanna Instruments
Hanna Instruments HI 99181 Manual de usuario
Hanna Instruments
Hanna Instruments Conmet1 (HI 98305 Manual de usuario
Hanna Instruments
Hanna Instruments HI96720C Manual de usuario
Hanna Instruments
Hanna Instruments HALO 2 HI9810332 Manual de usuario
Hanna Instruments
Hanna Instruments HI 96804 Manual de usuario
Hanna Instruments
Hanna Instruments HI99165 Manual de usuario
Hanna Instruments
Hanna Instruments HI 718 Manual de usuario
Hanna Instruments
Hanna Instruments HI 93703-11 Manual de usuario
Hanna Instruments
Hanna Instruments HI96704C Manual de usuario
Hanna Instruments
Hanna Instruments HI9812-51 Manual de usuario
Hanna Instruments
Hanna Instruments HI 4521 Manual de usuario
Hanna Instruments
Hanna Instruments HI 93716 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario