HAMPTON BAY 44 in Hawkins Manual de usuario

Hawkins

44 in Ceiling Fan

Owner’s Manual

Hawkins

Ventilador de Techo de 1,12 m

Manual del Propietario

117 391

44” Hawkins

Ceiling Fan by Hampton Bay

Date Purchased

Store Purchased

UL Model No.

Serial No.

Vendor No.

UPC

Thank you for purchasing our ceiling fan. This product has been

manufactured with the highest standards of safety and quality.

Table of Contents

Safety Rules . . . . . . . . . . . . . . . . . . . . 1

Unpacking Your Fan . . . . . . . . . . . . . . 2

Installing Your Fan . . . . . . . . . . . . . . . 3

Operating Your Fan . . . . . . . . . . . . . . . 8

Care of Your Fan . . . . . . . . . . . . . . . . . 9

Troubleshooting . . . . . . . . . . . . . . . . . . 9

Specifications . . . . . . . . . . . . . . . . . . 10

Warranty Information . . . . . . . . . . . . 11

117-391

792145351955

11289

Safety Rules - Read and Save These Instructions

To reduce the risk of electric shock, insure electricity has been turned off

at the circuit breaker or fuse box before beginning.

All wiring must be in accordance with the National Electrical Code

“ANSI/NFPA 70-1999” and local electrical codes. Electrical installation

should be performed by a qualified licensed electrician.

WARNING: To reduce the risk of electrical shock or fire, do not use this

fan with any solid-state fan speed control device. It will permanently

damage the electronic circuitry.

CAUTION: To reduce the risk of personal injury, use only the screws

provided with the outlet box.

The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 pounds, Use only UL

Listed outlet boxes marked “FOR FAN SUPPORT.”

The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge of the blades to the floor.

Avoid placing objects in path of the blades.

To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

Do not use water or detergents when cleaning the fan or fan blades. A dry

dust cloth or lightly dampened cloth will be suitable for most cleaning.

After making electrical connections, spliced conductors should be turned

upward and pushed carefully up into outlet box. The wires should be

spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box and ungrounded conductor on the

other side of the outlet box.

All set screws must be checked and retightened where necessary before

installation.

10.

11.

WARNING

TO REDUCE THE RISK OF PERSONALL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN

INSTALLING THE BRACKETS, BALANCING THE BLADES OR

CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS IN –

BETWEEN ROTATING FAN BLADES.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET

BOX.

Unpacking Your Fan Unpack your fan and check the contents. You should have the following items:

Set of blades (5)

Mounting bracket

Fan motor assembly

Motor housing

Blade arms (5)

Pull chain and fob

Blade Attachment Hardware

(16 Screws with Fiber Washers)

Electrical Hardware

(3 Plastic Wire Nuts)

Balance Kit

WARNING

DO NOT INSTALL OR USE FAN IF ANY

PART IS DAMAGED OR MISSING.

CALL TOLL FREE 1-877--898-1881.

Figure 2

Figures 1 and 2 are examples of different ways to

mount the outlet box.

Outlet Box

Figure 1 To hang your fan where there is an existing fixture

but no ceiling joist, you may need an installation

hanger bar as shown in Figure 3 (available at any

Home Depot retailer).

Figure 3

Outlet Box

Installing Your Fan

If there isn't an existing UL listed mounting box,

then read the following instructions. Disconnect

the power by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 35 lbs). Do not use plastic outlet boxes.

Tools Required

Mounting Options

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN

ONLY TO AN OULET BOX MARKED ACCEPT-

ABLE FOR FAN SUPPORT AND USE THE

MOUNTING SCREWS PROVIDED WITH THE

OULET BOX. OUTLET BOX COMMONLY USED

FOR THE SUPPORT OF LIGHTING FIXTURE

MAY NOT BE ACCEPTABLE FOR FAN SUPPORT

AND MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Phillips screwdriver, straight slot screwdriver,

adjustable wrench, step ladder, and wire cutters.

Outlet Box

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly.

Hanging the Fan

Making the Electrical

Connections

Attach the mounting bracket to the outlet box

with two screws and washers provided with the

outlet box. Make sure the bracket is tight and

secured (Fig. 4).

Lift fan into position by hanging the motor

assembly onto the hook from the ceiling

mounting bracket allowing it to hang freely

(Fig. 5).

Connect the ground cnductor of the 120V

supply (this may be a bare wire or a wire with

green colored insulation) to the green ground

lead(s) of the fan (Figure 6).

Connect the fan motor white wire to the supply

white (neutral) wire using a wire nut. (Figure

Connect the fan motor black wire to the supply

black (hot) wire using a wire nut (Figure 6).

Connect the blue wire for light kit to the black

household supply wire.

Turn wire nut connections upward, spreading

them apart so the green (ground) will be on one

side of the outlet box and the white, black and

blue wire will be on the other side, and push

carefully up into the outlet box.

Figure 5

Figure 4

Outlet Box

Mounting Bracket

REMEMBER to disconnect the power.

If you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

Follow the steps below to connect the fan to your

household wiring. Use the wire nuts supplied with

your fan. Secure the wire nuts with electrical tape.

Make sure there are no loose strands or

connections.

WARNING

CHECK TO SEE THAT ALL CONNECTIONS ARE

TIGHT, INCLUDING GROUND, AND THAT NO

BARE WIRE IS VISIBLE AT THE WIRE NUTS.

EXCEPT FOR THE GROUND WIRE.

WARNING

ELECTRICAL DIAGRAMS ARE FOR REFER-

ENCE ONLY. OPTIONAL USE OF ANY LIGHT

KIT SHELL BE UL LISTED AND MARKED

SUITABLE FOR USE WITH THIS FAN.

Motor

Figure 6

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green Ground

Lead

Ground to

Fan

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 7

Figure 8

Move fan into position over the four mounting

studs and secure with the provided washers and

nuts (Fig. 7).

Raise the motor housing up against the

mounting bracket, the four supports inside the

housing should be placed against the four studs

on mounting bracket, twist the housing

clockwise until snug (Fig. 8).

Finishing the Fan

Installation

Washers

Nuts

Mounting

Studs

Motor

Housing

Studs

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK. DO NOT USE THIS FAN WITH ANY

SOLID-STATE SPEED CONTROL DEVICE.

Attaching the Fan Blades

Step 1. Attach blades to blade arms using three

screws with fiber washers. (Fig. 9) Start a screw

into the blade arm, do not tighten. Repeat for the 2

remaining screws and washers.

Step 2. Tighten each screw securely starting with

the center screw. Make sure the blade is straight.

Repeat steps for the remaining blades.

Step 3. Fasten the blade assemblies to the motor

housing by lining up the slots of the blade arms

with the tabs on the motor housing, then tighten

the two screws and washers already installed in the

blade arms. (Fig. 10)

Figure 9

Blade Arm

Screws with

Fiber Washers

Blade

Figure 10

Motor

Blade Assembly

Slot

Tab

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE ARMS WHILE

INSTALLING, BALANCING THE BLADES, OR

CLEANING THE FAN. DO NO INSERT FOREIGN

OBJECTS BETWEEN ROTATING FAN BLADES.

Blade Balancing

Figure 11

Check that all blade and blade arm screws are secure.

Most fan wobble problems are caused when blade levels are unequal.

Check this level by selecting a point on the ceiling above the tip of one of

the blades. Measure from a point on the center of each blade to the point

on the ceiling. Measure this distance as shown in Figure 11. Rotate the fan

until the next blade is positioned for measurement. Repeat for each blade.

Measurements deviation should be within 1/8˝. Run the fan for 10

Minutes.

Use the enclosed Blade Balancing Kit if the blade wobble is still

noticeable.

The following procedure should correct most fan wobble. Check after each

step.

Touching Ceiling

Operating Your Fan

Warm weather - (Counter Clockwise Direction)

A downward air flow creates a cooling effect as

shown in Figure 12. This allows you to set your air

conditioner on a higher setting without affecting

your comfort.

Cool weather - (Clockwise Direction) An upward

air flow moves warm air off the ceiling are as

shown in Figure 13. This allows you to set your

heating unit on a lower setting without affecting

your comfort.

Turn on the power and check the operation of the

fan. The pull chain controls the fan speed as

follows:

1 pull - High

2 pulls - Medium

3 pulls - Low

4 pulls - Off.

Speed settings for warm or cool weather depend

on factors such as the room size, ceiling height,

number of fans, and so on.

The slide switch controls directions: forward

(switch down) or reverse (switch up).

NOTE

WAIT FOR FAN TO STOP BEFORE REVERSING

THE DIRECTION OF THE BLADE ROTATION.

Figure 12

Figure 13

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de HAMPTON BAY

HAMPTON BAY

HAMPTON BAY 1005 819 968 Manual de usuario

HAMPTON BAY

HAMPTON BAY 476-317 Manual de usuario

HAMPTON BAY

HAMPTON BAY Carrolton Manual de usuario

HAMPTON BAY

HAMPTON BAY 786-756 Manual de usuario

HAMPTON BAY

HAMPTON BAY Gazebo 473-131 Manual de usuario

HAMPTON BAY

HAMPTON BAY Antigua Plus Manual de usuario

HAMPTON BAY

HAMPTON BAY 460-952 Manual de usuario

HAMPTON BAY

HAMPTON BAY 69156 Manual de usuario

HAMPTON BAY

HAMPTON BAY Havenville 149*51 Manual de usuario

HAMPTON BAY

HAMPTON BAY LDS-BF2002 Manual de usuario

HAMPTON BAY

HAMPTON BAY 567-472 Manual de usuario

HAMPTON BAY

HAMPTON BAY Glendale Manual de usuario

HAMPTON BAY

HAMPTON BAY AG510-BN Manual de usuario

HAMPTON BAY

HAMPTON BAY SW18030 ORB Manual de usuario

HAMPTON BAY

HAMPTON BAY Sabitini Manual de usuario

HAMPTON BAY

HAMPTON BAY 434-972 Manual de usuario

HAMPTON BAY

HAMPTON BAY Asbury Plus Manual de usuario

HAMPTON BAY

HAMPTON BAY AM213-BN Manual de usuario

HAMPTON BAY

HAMPTON BAY 91126 Manual de usuario

HAMPTON BAY

HAMPTON BAY Garibaldi Manual de usuario

HAMPTON BAY

HAMPTON BAY Northport 178-047 Manual de usuario

HAMPTON BAY

HAMPTON BAY METARIE II 24 Manual de usuario

HAMPTON BAY

HAMPTON BAY 803-548 Manual de usuario

HAMPTON BAY

HAMPTON BAY 285-167 Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje