Halsey Taylor HTHB-HAC Manual de instalación

Page 1

1000001732 (Rev. D - 06/16)

HAC-HB*1B HAC-HB-NF-*1B

HTHB-HAC

Retrot Hydroboost Bottle Filling Station

HTHB-HAC Bottle Fillers are among the easiest to install on the market today. To

insure you install these models easily and correctly, PLEASE READ THESE

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK

YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL,

AND OTHER APPLICABLE CODES. After installation, leave these instructions with

the Fountain for future reference.

IMPORTANT

THIS IS AN INDOOR APPLICATION ONLY.

ALL SERVICE TO BE PERFORMED BY AN

AUTHORIZED SERVICE PERSON.

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCHAS TELEPHONE, COMPUTERS, ETC. TO WATER LINES

IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE

BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN

ELECTROLYSIS WHICH CAUSES A METALLIC TASTE ORAN INCREASE IN THE METAL CONTENT OF THE WATER.

THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS

PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN

FROM THE BUILDING PLUMBING SYSTEM. WE SUGGEST THAT THE BOTTLE FILLING STATION AND WATER

COOLER BE PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI).

INSTALLER

TOOLS REQUIRED

BUT NOT PROVIDED:

SAFETY GLASSES

GLOVES

ELECTRIC DRILL

3/4” WRENCH OR CRECENT

WRENCH

UTILITY KNIFE

TAPE MEASURE

PENCIL

5/32” ALLEN WRENCH

Installation/Care/Use Manual

Buy at

| 855-558-9600 |

BottleFillingStations.com

Page 2

HAC-HB*1B HAC-HB-NF-*1B

1000001732 (Rev. D - 06/16)

WATER COOLER PREPARATION

3) Remove Basin Fasteners

• Remove Basin Assembly by loosening

eight (8) screws, four on each side of

basin.

Remove Front Panel

Loosen Drain Line

Remove Basin Fasteners

1) Remove Front Panel

•Remove lower front panel of water cooler

by removing the four (4) screws, two at

top and two at bottom. On Two Level

Models, remove both front panels.

•WARNING: Before proceeding.

Disconnect electrical power supplying the

water cooler. Switch circuit breaker “OFF”

or remove fuse.

•Unplug water cooler power cord from

electrical outlet.

•Shut off water supply.

NOTE:

• On Two Level Models, the Bottle Filling Unit MUST be mounted on the higher unit:

• Two Level Standard Models; high unit is on Left Hand(LH) side.

• Two Level Reverse Models; high unit is on Right Hand(RH) side.

2) Loosen Drain Line

• Loosen Slip-Joint Nut at P-trap.

• Note: Have container/bucket readily available

to catch water from lines.

Buy at

| 855-558-9600 |

BottleFillingStations.com

Page 3

1000001732 (Rev. D - 06/16)

HAC-HB*1B HAC-HB-NF-*1B

4) Remove Bubbler Water Line

• Disconnect water line from bubbler.

Remove Bubbler Water Line

5) Lift and Remove Basin.

• Remove basin assembly by lifting straight

up, disconnecting the drain line from the

P-trap.

Lift and Remove Basin.

Exchange Drain hardware.

6) Assemble Drain hardware.

• Remove drain hardware from original

basin.

• Remove the protective covering from the

basin.

• Reinstall the drain elbow, drain plug, and

strainer plate on to the new basin

•Attach the new drain hardware onto the new

basin.

Exchange Bubbler hardware.

WATER COOLER PREPARATION

7) Exchange Bubbler hardware.

• Remove bubbler hardware from original basin.

•Reinstall the bubbler hardware on to the new

basin.

• Ensure the bubbler is properly positioned

with the stream falling onto the center of

splash ridge.

Buy at

| 855-558-9600 |

BottleFillingStations.com

Page 4

HAC-HB*1B HAC-HB-NF-*1B

1000001732 (Rev. D - 06/16)

HWF3000 WATERSENTRY PLUS FILTER INSTALLATION

WARNINGS:

• Do not use with water that is microbiologically unsafe or of unknown quality. For potable water only.

• Do not use with a hot water supply. Rated for water temperature: 33°-100°F(2°-38°C)

• Waterlinepressuremustnotexceed100psi(690kPa).Useaninlinewaterpressureregulatorbeforelter

to limit maximum pressure. Rated water supply pressure: 20-100psi(138-690kPa).

• Filter kits must be installed in compliance with all state and local laws and regulations governing the

installation and use of this product.

NOTE:

•Ends of tubing must be cut square and free of

burrs and sharp ends that could cut or nick

the o-rings.

•Loosen the locknut and push tube end past

botho-ringstoapositivestopinthelter

head recess - approx. 1".

•Locknut may have to be backed out a little

more. Screw the locknut hand tight to seal.

AttachportttingsontoFilterHead

2) Attach Filter head assembly.

• If not already preassembled. Attach Filter

headassemblytoltermountingbracket

with four(4) screws supplied.

Single Level Models

Two Level Models

•Single Level Models

•Mount with 3/8” inlet on Right Side

• Two Level Models

• Mount with 3/8” Inlet on Left Side

Note: Screw the locknut hand tight to seal

1) Attach port ttings onto Filter Head:

• Note: Refer to photos at left for proper

alignment.

•Insert3/8”90°ElbowttingintoINport,

• Insert 1/4” poly tube into OUT port. If

necessary, insert a 1/4” x 90° Elbow.

•Adjustandtightenportttings.

B CA

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

A B C

Buy at

| 855-558-9600 |

BottleFillingStations.com

Page 5

1000001732 (Rev. D - 06/16)

HAC-HB*1B HAC-HB-NF-*1B

3) Mount Filter Head Assembly

Mount Filter Head Assembly into Cooler.

Unit with single supplied screw:

4) Connect Building water supply.

• Remove the 3/8” water inlet from the in-line

strainer.

•Connect 3/8” poly tubing between the inlet of the

lterandthewaterinletusingthesupplied

3/8” -3/8” union connector.

•Discard in-line strainer.

Single Level Models

Two Level Models

• Single Level Models

• Mount on inside of left panel butted up against

top lip.

• NOTE:Thelterbracketismountedwitha

single screw.

• Two Level Models

• Mount in left hand cooler on the inside of the

right panel, butted up against the top lip.

• NOTE:Thelterbracketismountedwitha

single screw.

HWF3000 WATERSENTRY PLUS FILTER INSTALLATION

Fig. 1

Buy at

| 855-558-9600 |

BottleFillingStations.com

Page 6

HAC-HB*1B HAC-HB-NF-*1B

1000001732 (Rev. D - 06/16)

1) Connect Water Supply:

• Remove the in-line strainer outlet tube from

the Regulator Inlet.

• Remove the 1/4” copper tubing from the

Regulator Outlet.

• Connect the in-line Strainer Outlet using 1/4”

poly tubing to the Evaporator 1/4” copper

inlet using the supplied 1/4” union.

2) Add water supply to Bottle Filler:

• Cut the Evaporator outlet 1/4” poly tubing

6” from the Evaporator Outlet and insert

the1/4”Teettingbetweenthetwopieces.

• ConnectBottleFillersupplylinetoteetting.

• Remove 1/4” poly tubing from Bubbler.

3) Re-route water supply to Regulator Inlet:

• Insert end of 1/4” poly tubing from the

TeettingtotheRegulatorInletwhichis

marked with the word “IN” on the regulator.

4) Connect water supply from Regulator to Bubbler:

• Cut a 12” piece of 1/4” poly tube along with

matching length of insulation.

• Insert 1/4” poly tube into insulation.

•Insert 1/4” poly tube into the Regulator

Outlet (unmarked).

•Opposite end of 1/4” poly tube will be

inserted later into the Bubbler.

RE-PLUMBING SINGLE STATION WATER CIRCUITS (NON-FILTER)

CAUTION:

• This procedure MUST be performed on ALL SINGLE HALSEY TAYLOR WATER COOLERS or the bottle

llingunitWILL NOT perform properly!

• When disconnecting water lines use a container to catch any water running out of the lines.

IN-LINE

STRAINER

REGULATOR

1/4”UNION

REGULATOR TEE

TO BOTTLE

FILLER

6” TUBING

EVAPORATOR

INLET

EVAPORATOR

OUTLET

EVAPORATOR

OUTLET

EVAPORATOR

STANDARD HAC PLUMBING

HAC HYDROBOOST PLUMBING

Fig. 2

IN-LINE

STRAINER

12” TUBING

B CA

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

A B C

TO BUBBLER

EVAPORATOR

INLET

Buy at

| 855-558-9600 |

BottleFillingStations.com

Page 7

1000001732 (Rev. D - 06/16)

HAC-HB*1B HAC-HB-NF-*1B

RE-PLUMBING SINGLE STATION WATER CIRCUITS (WITH FILTER)

CAUTION:

• This procedure MUST be performed on ALL SINGLE HALSEY TAYLOR WATER COOLERS or the bottle

llingunitWILL NOT perform properly!

• When disconnecting water lines use a container to catch any water running out of the lines.

FILTER

HAC HYDROBOOST PLUMBING

1) Connect Water Supply:

• Remove the in-line strainer outlet tube from

the Regulator Inlet.

• Remove the 1/4" copper tubing from the

regulator Outlet.

• Connect the Filter outlet using 1/4” poly

tubing to the Evaporator 1/4” copper inlet

using the supplied 1/4” union.

2) Add water supply to Bottle Filler:

• Cut the Evaporator Outlet 1/4” poly tubing

6” from the Evaporator Outlet and insert

the1/4”Teettingbetweenthetwopieces.

• ConnectBottleFillersupplylinetoTeetting.

• Remove 1/4” poly tubing from Bubbler.

3) Re-route water supply to Regulator:

• Insertendof1/4”polytubingfromtheTeetting

to the Regulator Inlet. which is marked with

the word “IN” on the Regulator.

4) Connect water supply from Regulator to Bubbler.

• Cut a 12” piece of 1/4” poly tube along with

matching length of insulation.

• Insert 1/4” poly tube into insulation.

•Insert 1/4” poly tube into the Regulator Outlet

(unmarked).

•Opposite end of 1/4” poly tube will be Inserted

later into the Bubbler.

Fig. 3

IN-LINE

STRAINER

STANDARD HAC PLUMBING

1/4”UNION

EVAPORATOR

INLET

EVAPORATOR

6” TUBING

TEE

EVAPORATOR

OUTLET

12” TUBING

REGULATOR

TO BOTTLE

FILLER

TO BUBBLER

EVAPORATOR

INLET

REGULATOR EVAPORATOR

OUTLET

TO BUBBLER

Buy at

| 855-558-9600 |

BottleFillingStations.com

Page 8

HAC-HB*1B HAC-HB-NF-*1B

1000001732 (Rev. D - 06/16)

RE-PLUMBING TWO LEVEL STATION WATER CIRCUITS (NON-FILTER)

CAUTION:

• This procedure MUST be performed on ALL TWO LEVEL HALSEY TAYLOR WATER COOLERS or the bottle

llingunitWILL NOT perform properly!

• When disconnecting water lines use a container to catch any water running out of the lines.

1) Add water supply to Bottle Filler:

• In the left hand unit, cut the Evaporator Outlet 1/4” poly tubing 5” from the access opening between the units

andinsertthe1/4”Teettingbetweenthetwopieces.

Fig. 4

HAC TWO LEVEL HYDROBOOST PLUMBING

STANDARD HAC TWO LEVEL PLUMBING

TO BUBBLER

REGULATOR

EVAPORATOR

INLET

EVAPORATOR

TO BUBBLER

EVAPORATOR

OUTLET

TEE

5”

TO BOTTLE

FILLER

IN-LINE STRAINER

L.H. DUMMY UNIT

R.H. REFRIGERATED UNIT

TO BUBBLER REGULATOR

IN-LINE STRAINER EVAPORATOR

INLET TO BUBBLER REGULATOR

EVAPORATOR

OUTLET

EVAPORATOR

REGULATOR

Buy at

| 855-558-9600 |

BottleFillingStations.com

Page 9

1000001732 (Rev. D - 06/16)

HAC-HB*1B HAC-HB-NF-*1B

RE-PLUMBING TWO LEVEL STATION WATER CIRCUITS (WITH FILTER)

CAUTION:

• This procedure MUST be performed on ALL TWO LEVEL HALSEY TAYLOR WATER COOLERS or the

bottlellingunitWILL NOT perform properly!

• When disconnecting water lines use a container to catch any water running out of the lines.

HAC HYDROBOOST TWO LEVEL PLUMBING

STANDARD HAC TWO LEVEL PLUMBING

1) Connect Water Supply:

• In the left hand unit,connect the Filter outlet using 1/4” poly tubing to the Evaporator 1/4” copper inlet using

thesupplied1/4”quickconnecttting.

2) Add water supply to Bottle Filler:

• In the left hand unit, cut the Evaporator outlet 1/4” poly tubing 5” from the access opening between the units

andinsertthe1/4”Teettingbetweenthetwopieces.

TO BUBBLER

REGULATOR

IN-LINE STRAINER

REGULATOR

FILTER

Fig. 5

L.H. DUMMY UNIT

R.H. REFRIGERATED UNIT

EVAPORATOR

OUTLET

EVAPORATOR

INLET

L.H. DUMMY UNIT

R.H. REFRIGERATED UNIT

EVAPORATOR

OUTLET

EVAPORATOR

INLET REGULATOR

5”

TEE

TO BUBBLER

TO BOTTLE

FILLER

TO BUBBLER

REGULATOR

Buy at

| 855-558-9600 |

BottleFillingStations.com

Page 10

HAC-HB*1B HAC-HB-NF-*1B

1000001732 (Rev. D - 06/16)

1) Connect Water Line

•Connect water line from Regulator to

Bubbler.

2) Install New Basin Assembly

•Reposition Basin Assembly (Basin with

Drain and Bubbler hardware) back onto

the cooler.

•Reattach drain line to P-trap and tighten.

3) Fasten Basin Assembly in place.

•Insert and retighten the 8 screws, four per

side.

BASIN ASSEMBLY PREPARATION

Reattach drain line to P-trap

Connect Water Line

Fasten Basin Assembly in place.

Buy at

| 855-558-9600 |

BottleFillingStations.com

Otros manuales para HTHB-HAC

Tabla de contenidos

Otros manuales de Sistema de agua de Halsey Taylor

Halsey Taylor

Halsey Taylor HTVZDBL*1C series Manual de usuario

Halsey Taylor

Halsey Taylor WCFS G L R Series Manual de usuario

Halsey Taylor

Halsey Taylor HydroBoost HTHBSM-1A Instrucciones de uso

Halsey Taylor

Halsey Taylor HOF14A-FR-Q 1D Series Manual de usuario

Halsey Taylor

Halsey Taylor HVRGRN8WSNF 1C Series Manual de usuario

Halsey Taylor

Halsey Taylor GreenSpec HTHB-HVRGRN Manual de instalación

Halsey Taylor

Halsey Taylor HTVZD*1C series Manual de usuario

Halsey Taylor

Halsey Taylor S300-2EQ 1N Series Manual de usuario

Halsey Taylor

Halsey Taylor HVRGRN8WSNF 1B Series Manual de instalación

Halsey Taylor

Halsey Taylor HBW8AQ 1M Series Manual de usuario

Halsey Taylor

Halsey Taylor HOF14AFRQ 1F Series Manual de usuario

Manuales populares de Sistema de agua de otras marcas

Spirotech

Spirotech SPIROVENT SUPERIOR S250 Manual de usuario

Culligan

Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manual de usuario

A.O. Smith

A.O. Smith Dura-Max AJH - 1000A - P Manual de usuario

Microline

Microline T.F.C.-4 Manual

Eureka Forbes

Eureka Forbes Aquaguard Select Manual de usuario

Cetetherm

Cetetherm AquaEfficiency Manual de usuario

CB Tech

CB Tech CB-VOC Manual de usuario

Vaillant

Vaillant auroFLOW plus VPM 15 D Manual de usuario

resideo

resideo Braukmann HS10S Manual de usuario

Gude

Gude INOX 100/24 Manual de usuario

Mono

Mono Eco 1-60 Manual

SpectraPure

SpectraPure Drinking Water Kit Manual de usuario

HydroCare

HydroCare Dual Action Manual de usuario

NEXT pool

NEXT pool STERILOR Cu/Ag Diagrama de cableado

Alpha

Alpha SolarSmart 150 Guía del usuario

TA FRISTAR3 Manual de usuario

GÜDE

GÜDE HWA 800 K Manual de usuario

Rainfresh

Rainfresh UCS2 Manual de usuario