Hallicrafters HA-1 Manual de capacitación

SECTION I

GENERAL

1-1. DESCRIPTION

The Hallicrafters Model HA-1 T.O.Keyer ® employs digital circuitry, similar

to that found in modern digital computers, to form perfect code characters at any

speed. E perienced operators appreciate its stability and precision of operation,

and novice operators discover a new command of CW that leads to proficiency

and unsuspected enjoyment. The keyer operates much in the same way as a tape

transmitter; the dash-dot and mark-space ratios remain constant over the speed

range and the speed and mark-space adjustments are completely independent.

The key lever is a remote control unit that may be placed in any convenient

operating position. This conserves the operating area, permits ready mechanical

adjustments, and allows the operator his choice of key levers.

Additional features of the keyer include a pleasant sidetone signal with

volume control for practice, instruction or monitoring ... an e ceptionally wide

speed range ... a silent mercury-wetted relay of virtually unlimited life ... complete

immunity to line-voltage fluctuations and RF pickup ... rear connections for

break-in operation and au iliary control, and for e ternal sidetone and key lever

connections ... and a transformer power supply, with silicon rectifiers and

complete voltage regulation for top reliability.

1-2. STANDARDS FOR THE INTERNATIONAL MORSE CODE

The International Morse code replaced the older Morse code for radio

communications when the tape perforator and keying head, along with the high-

speed ink-slip recorder, were developed for commercial service. This early

automation of our CW is still widely employed, handling traffic comfortably at 300

WPM. The perforator and keying head provide the "perfect fist" and the standards

for CW which make it easy to send and receive with the proper scientific

economy.

The relative duration of the dot and the space is called the mark-space ratio,

usually adjusted for 1-to-1. A dash is formed by bridging the space between two

dots. The spaces between dots and dashes in a letter are uniform. A standard

word is equivalent to 24 dot and spaces. 10 WPM (words per minute) is therefore

240 dots per minute, or 4 dots per second.

SECTION II

SPECIFICATIONS

POWER SOURCE .......................... 105 to 125 volts, 60 cycles AC, 25 watts.

SPEED RANGE ............................. Low: 10 to 30 WPM.

High: 25 to 65 WPM.

KEYING MONITOR ........................ Self-contained tone generator and PM

speaker. Rear chassis mounted PHONES

jack disconnects speaker when phones

are inserted.

TRANSMITTER KEYING ................ Mercury-wetted contact relay switching nor-

mally open or normally closed to ground.

(See paragraph 3-4-1-2).

KEY LEVER INPUT ........................ Three-circuit jack mounted on front panel

accepts 1/4 inch diameter plug (Switchcraft

type 267 or equivalent) or rear control outlet

connections. (See paragraph 3-3).

CONTROL OUTLET ....................... Eight-pin octal socket mounted on rear panel

accepts standard octal plug (supplied).

DIMENSIONS (OVERALL) .............. 5-5/8 × 7 × 7-13/16 inches (HWD).

NET WEIGHT ................................ 7-1/2 pounds.

SHIPPING WEIGHT ....................... 10 pounds.

SECTION III

INSTALLATION

3-1. UNPACKING

After unpacking the Model HA-1 keying unit, e amine it closely for any

possible damage which may have occurred during transit. Should any sign of

damage be apparent, file a claim immediately with the carrier stating the e tent of

the damage. Carefully check all shipping labels and tags for any special

instructions before removing or destroying them. Remove all protective shipping

material around tubes and components.

3-2. LOCATION

The keyer should be placed in a location which permits free circulation of air

around the cabinet, particularly at the rear. Avoid e cessively warm locations

such as those near radiators and heating vents.

The mercury-wetted relay employed requires that the keyer be operated in a

position no greater than 30° from a horizontal plane.

3-3. KEY LEVER

Various styles of commercially built key levers are available for use with

electronic keyers. Any of these are suitable for use with the Model HA-1 keying

unit. Connections to the key and panel jack are made as shown in figure 2. Key

lever connections are also provided at the control socket on the rear of the unit

(See paragraph 3-4-1-1).

Figure 2. Key Lever Cord for Front Panel Key Connection.

It can be noted by referring to the schematic diagram, figure 9, that the key

lever base is connected to chassis ground and the dot-dash contacts are operated

at an e tremely low negative potential. This makes the key assembly completely

free from shock hazard.

3-4. REAR CHASSIS RECEPTACLES

Receptacles are provided on the rear of the keyer for the following purposes.

3-4-1. CONTROL OUTLET (See figure 3)

An eight-pin socket is provided to connect the Model HA-1 keying unit into

the station control system. The mating connector for this socket is an Amphenol

type CP-8 (one is supplied).

3-4-1-1.AUXILIARY KEY LEVER CONNECTIONS (Pin 1, 5 and 8)

At the user's option, the key lever may be connected to the control outlet

instead of to the panel key jack. Pin 1 is chassis ground, pin 5 is switched to

ground for dots, and pin 8 is switched to ground for dashes.

Figure 3. Control Outlet Connections.

3-4-1-2.KEYING CONTACTS (Pin 2 3 and 4)

Pin 2 (normally open to ground) is normally used for transmitter keying

purposes.

Pin 3 and 4 (independent, normally closed to ground) are provided for

au iliary control of station facilities.

IMPORTANT

The mercury-wetted relay contact rating is 5 amperes ma imum, or 500

volts ma imum, the product not to e ceed 250 voltamperes with contact

protection. For e ample, the ma imum allowable voltage with a 5-

ampere load is 50 volts ( 5 A × 50 V = 250 VA); the ma imum allowable

current with a 500-volt supply is 0.5 ampere (500 V × 0.5 A = 250 VA).

Refer to paragraph 3-5 for method of determining required contact

protection network.

3-4-1-3.Speaker (Pin 6) AND AUDIO OUTPUT (Pin 7)

A standard circuit transfer type PHONES jack (J1) on the rear apron

automatically disconnects the internal speaker when the phone plug is inserted.

Output impedance is 3.2 ohms, although it is suitable for use with any low or

medium impedance headsets.

Figure 4. Typical Station Installation.

3-4-3. GROUNDING POST

The ground post, provided at the rear of the keyer, should be utilized to

establish a ground for this unit.

IMPORTANT

It is recommended that the unit permanently connected to the

station grounding system so as to prevent the possibility of a

shock hazard developing as a result of component failure.

3-5. RELAY CONTACT PROTECTION NETWORK

E cept for very light loads (under 2 mA and 50 V), the relay must be

provided with a contact protection network consisting of a capacitor and resistor

in series. This network is shown in the lower right-hand corner of the chassis in

figure 4. The network prevents possible arcing which would eventually destroy

the contacts. The voltage and current requirements of the circuit to be keyed

should be determined, and the relay contacts provided with an appropriate

protection network prior to the connection into the circuit.

The chart (figure 5) affords a convenient means of determining the necessary

contact protection.

Hallicrafters Model HT-30, HT-32, HT-32A, HT-32B, HT-37, HT-44, SR-150

and SR-160 Transmitters require no protection network when used with this

keyer.

For the most effective protection, the network, as determined from the chart,

should be installed as close to the relay contacts as is possible. It is desirable to

install the network internally, directly at the relay socket; however, adequate

protection will be provided by installing the network at the network at the control

outlet.

To determine the proper protection network required for loads e ceeding 2

mA or 50 volts, proceed as follows:

(1) Measure load current of circuit to be keyed with a suitable ammeter.

(2) Measure open circuit load voltage at the keying points.

(3) To find C, read directly up from the value of load current on the

horizontal scale to its intersection with the sloping capacity line; the

value of C is determined from the right hand scale.

To find R, read directly up from the load current value to its

intersection with the appropriate load voltage line; the value of R is

read from the left-hand scale.

E ample I: A circuit maintaining a load current of 2.0 amperes and

an open circuit load voltage of 100 volts would require a C value of

0.4 µF and an R value of appro imately 3.6 ohms. (See dotted lines

on chart).

E ample II: Measured current and voltage is 50 mA and 150 V

respectively.

Solution: The proper protecting network would be a 0.001 µF

capacitor (Limiting capacity) in series with a 750 ohm resistor.

In current and voltage applications beyond the scope of the chart, the

minimum limiting capacitance value of 0.001 µF and a ma imum resistance

value of 10,000 ohms should be used in the protection network.

Figure 5. Relay Contact Protection Chart.

SECTION IV

FUNCTIONS OF OPERATING CONTROLS

4-1. FUNCTION SWITCH

The FUNCTION control is a four-position rotary switch: (1) turns the unit ON

and OFF, (2) selects low or high speed operation, and (3) has a center HOLD

position for transmitter tuning purposes (key down).

4-2. SPEED CONTROL

The SPEED control provides a means of adjusting the keying speed between

10 and 30 WPM when the FUNCTION switch is in the LOW position or between

25 and 65 WPM in the HIGH position.

4-3. SIDETONE CONTROL

The SIDETONE control (knurled shaft), accessible at the rear of the unit,

adjusts the amplitude of the keyed monitor tone.

4-4. BALANCE CONTROL

The BALANCE control (screwdriver slot shaft), mounted at the rear of the

unit, differentially adjusts the gain of tube V3 to compensate for tube section

differences and aging. The adjustment should remain fi ed for long periods of

time and need only be readjusted when V3 is replaced or when major service has

been performed.

To adjust the BALANCE control proceed as follows

(1) Turn the control to its ma imum counterclockwise position. The unit

will key a continuous dash. Advance the control in the clockwise

direction, and note the point at which the dash stops.

(2) Turn the control to its ma imum clockwise position and close the key

to dash. The unit will key a continuous series of dots as long as the

key is held closed to dash. Adjust the control counterclockwise to the

point where self-completing dashes are formed. Note this setting.

(3) Set the control midway between the points noted in step 1 and 2

above. The BALANCE control is now properly set and should require

no further attention.

Tabla de contenidos

Otros manuales de Receptor de Hallicrafters

Hallicrafters

Hallicrafters S-77A Manual de capacitación

Hallicrafters

Hallicrafters Sky Champion S-20R Manual de usuario

Hallicrafters

Hallicrafters 5X-117 Manual de capacitación

Hallicrafters

Hallicrafters SX-115 Manual de capacitación

Hallicrafters

Hallicrafters S-40B Manual de capacitación

Hallicrafters

Hallicrafters SX-117 Instrucciones de funcionamiento

Hallicrafters

Hallicrafters S-85 Guía del usuario

Hallicrafters

Hallicrafters SX-43 Manual de usuario

Hallicrafters

Hallicrafters SX-140 Manual de capacitación

Hallicrafters

Hallicrafters Sky Champion S-20 Manual de usuario

Hallicrafters

Hallicrafters SX-140 Manual de capacitación

Hallicrafters

Hallicrafters SX-122 Manual de capacitación

Hallicrafters

Hallicrafters SX-100 MARK IA Manual de usuario

Hallicrafters

Hallicrafters SX-117 Manual de capacitación

Hallicrafters

Hallicrafters SX-43 Manual de usuario

Hallicrafters

Hallicrafters SR-75 Manual de capacitación

Hallicrafters

Hallicrafters Sky Challenger Manual de usuario

Hallicrafters

Hallicrafters SX25 Manual de capacitación

Hallicrafters

Hallicrafters S-119 Manual de capacitación

Hallicrafters

Hallicrafters SX-99 Manual de capacitación

Hallicrafters

Hallicrafters SX-62 Manual de capacitación

Hallicrafters

Hallicrafters S19-R Manual de capacitación

Hallicrafters

Hallicrafters S-72 Manual de capacitación

Hallicrafters

Hallicrafters SX-28 Instrucciones de funcionamiento

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario