Haier HWM80-0528 Manual de usuario

Please read this manual carefully before using.

Retain it for future reference.

Fully Automatic Washing Machine User's manual

This manual is for

HWM80-0528

CONTENTS

CONTENTS the 2nd cover

Names of the parts 1

Safety precautions 2

Installation and adjustment 4

Install the water inlet hose 6

Preparation before washing 8

Put in the laundries 9

Usage of the detergent

Use the operation buttons 10

Finish washing 12

Disposal after washing 13

Trouble-shooting Answer to question 14

Packing list 15

Specification table 16

Close the top lid 9

Drain bushing

Control panel

Inner tub

Detergent box

Top lid component

Balance ring

Lint filter

Pulsator

Front control

board

Cabinet

Adjustable leg

Fixed leg

(3 pieces)

Adjustable

leg film

Handle

Water absorption

cushion Hot water valve

Cold water valve

Power cord

Back cover

Names of the parts

Contents marked with that symbol are related to the

safety of the product and the personal safety of the

users. Please operate in strict conformity to the

contents, otherwise it may cause damage of the

machine or injure the personal safety of the user.

Contents marked with that symbol are actions forbidden

to perform. Performing of those actions may result in

damage of the machine or injure the personal safety of

the user.

Meaning and description of the symbols

Warning sign

Forbidden sign

ÅÅË®¹Ü¹Ò¿×

Protect cover

ÅÅË®¹Ü»¤Ì×

ÅÅË®¹Ü

Drain hose

(installed by user)

Screw cover

Hanging hole

for the drain

hose

Jacket of

drain hose

Notes: All illustrations in this Manual are given for reference only. Your products and

accessories may show differences from these illustrations due to our

continuous improvement.

Safety precautions

Do not let the machine share one receptacle with

other electric appliances. If the plugging into the

receptacles loose, do not use the plug any more.

If washing machine is supplied from a cord

extension set or electrical portable outlet device,

no cord extension set or electric portable outlet

device should be positioned so it is not subject to

splashing or ingress of moisture.

Do not wash water-proof

laundries like the raincoat, bike

covers etc. to avoid abnormal

vibrations in spinning.

Do not put the machine at damp place

like the bathroom. Never wash it with

water. Do not put wet laundries on the

control panel.

Do not use water hotter than 60 .

In case the washing machine is installed

on ground with carpet, do not block the

ventilation hole with carpet.

Ensure carpet does not

obstruct the

opening in

the bases.

Please plug the power plug on special

receptacle. Be sure to use three-pins

power receptacle. Ensure that the earthing

prong of the power receptacle is earthed

reliably. Use leakage protector if possible.

Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.

Keep the pin of the power plug clean, if the power plug is polluted with dust,

please wipe with dry cloth carefully.

If the supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly

qualified person in order to avoid a hazard.

The washing machine must be positioned

so that the plug is accessible. Be sure to pull

the plug off and close the water faucet in

following cases: power failure, delivering

the machine, setting the machine idle or

cleaning the machine.

Do not plug or pull the

power plug with wet

hand.

The ventilation holes

at the bottom

Carpet

Do not put hand into the rotating tub.

It is dangerous even if the rotation

speed is slow. Take special care of the

children. Keep children away from the

washing machine to avoid them climbing

on it.

The appliance is not instruct for use of

young children of infirm persons without

supervision.

Young children

should be

supervised to

ensure that they

do not play with

the appliance.

Do not decompose, repair or alter

the machine byyourself.

Do not putany hot orheavy items

(such as the kettle with hot water) on

the washing

machine.

Do not wash laundries with volatile

materials (such as

thinner,

petrol etc.).

Keep the machine away from

direct sunlight andheat source

like the heater.

The handicapped or children shall

not use the machine without care.

Benzene

Safety precautions

Toprevent the lintin the tubfrom blocking the

cascade outlet and influencing the cascade

effect, please keepthe lint filterin good

condition, and installit to properposition

during washing. Ifthe lint filteris lost or

damaged, please contactthe local

after-sales service departmentof our company.

To protect your laundries and washing

machine, please take out all of the coins,

buttons, sand, hairpin and other foreign

materials before washing.

Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.

It is suggested to use foamless washing powder.

Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,

please be sure to ensure the washer is placed under the room temperature for 24 hours and then use

otherwise the washing effects may be lowered or the washer may be damaged.

To change the direction of drain pipe, please contact the customer care agent of our company.

Install the bottom plate

After you open the package, please lean

the washing machine gently down on Soft

object ( like the towel cloth,blanket, etc. ).

Install the bottom plate to the bottom of the

machine with the eight screws by a cross

screwdriver, then lift the machine up gently.

See to the figure:

Please install and adjust the machine according to the requirement of

the manual. It is very important to your security and correct

operating the machine.

Installation and adjustment

The largest allowable slope of the shank base of the machine is 2 .The

slanting or rough ground will result in unstable running or stoppage of the

machine. Please adjust it with following methods:

Confirm it's horizontal:

Hang the lead line to check if it is

horizontal.

Adjust the adjustable leg:

Adjust the Installation position

1 .To twist the adjustable leg, please first

lift up the side of the leg slightly, loosen

the adjustable nut, and twist the leg.

2 .After adjustment, fasten the nut.

After opening thepackage, please take out the lint

filter from thedocument bag, install it tothe inner

tub. See tothe figure.

Install the lint filter

Inner tub

Lint filter

Drain hose

Ensure the drainhose si mounted at a suitableheight.

( above the floor).

Do not poke it too far down the drain pipe or silphoning will occur.

Between 800-1200mm

Fasten

Loosen

High Low

the adjustable nut

the adjustable

feet

Soft object

Bottom plate

Back

Screw

Front

How to change the direction of the drain hose

1.Dismantle the back cover of the washing

machine.

3.Dismantle the protecting cover of the

drain outlet at the other side (method

the same as the bushing). Install the

bushing as per indicated in Figure 4.

4.Extend the drain hose from the other

side. Fix the drain hose onto the base

frame with the drain hose frame. (As

indicated in Figure 5)

5.Install the protecting cover of the drain

outlet at the other side as per indicated

in Figure 6.

Drain outlet

protecting cover

Drain hose bushing Drain hose bushing

Figure 1

Figure 4

Figure 5

Figure 6

Drain hose

bushing

Take off

Drain hose

bushing claw

Cabinet

Figure 2

Figure 3

Inner

Press

Outer

2.Put down the drain hose. Take off the

drain hose frame. As indicated in Figure

1, put the drain hose into the cabinet.

Then stretch one hand into the cabinet

to nip the claw of the drain hose bush-

ing to remove the claw from original

position. Take off the drain hose bush-

ing with the other hand. (As indicated in

Figure 2 and 3).

Drain hose frame

Outer

drain

hose

Usage of the drain hose

The drainage shall be smooth with the drain hose

ut the drain hose up to suitable position.Do not

put it on ground.

Notes:the mouth of drain pipe should higher than

the water level of washing tub for avoiding

to siphon phenomenon during drain.

Do not tramp or press the drain hose.

Mouth of

drain hose

0.8<H<1.2m

Water tap,suitable Water tap,not suitable

It is requiredthat the front end shall be longer than 10mm.

The outlet endsurface of the tap shall be flat and smooth.If not please file it to

avoid leakage.

2.Loosen the screw till the water tap can be accessed. Put the jointer of the water

inlet hose on the tap. See to Figure 2. (If the tap diameter is too large and the jointer

can not be set on the water tap, please loosen the four screws and take out the

bushing in the jointer. See to the figure3.)

1.Press the lower end of the lock lever and push down the slider. Take off the water

inlet hose jointer from the water inlet hose component. See to Figure 1.

Remarks: Before twistingthe fastening nut, the thread is 4mm above the

upper surface ofthe nut. After twisting the fastening nut, thethread is 2mm

above the uppersurface of the nut. See to Figure 6.

4.Take off the nameplate. Twist the fastening nut as per the indication of the figure.

See to Figure 5.

3.Fasten the four screws evenly. See to Figure 4.

>10mm

Outlet end surface

Nut

About 4mm before twisting

About below 2mm after twisting

Screw

Screwdriver Mark label bushing

Figure 2

Figure 5

Figure 1

Figure 4

Figure 3

Figure 6

Slider

Water inlet pipe jointer

Water inlet pipe

Locking lever

Install the water inlet hose

Confirm the water tap

Connection between the water inlet hose jointer and

the water tap

1.Do not takeoff the water absorption

cushion. Please check if the cushion

is dropped or damaged before each

usage. If it happens please contact

our after-sale department immediately.

2.Put the nutof the waterinlet hose on

the valve jointer.

3.Fasten the nut.Swaying it gentlyto

confirm if it's suitable.

1.Close the watertap.

2.Press the lockinglever. Pushdown the slider. Then

pull off the water inlethose. If themachine is used

more than onceevery week, thejointer of thewater

inlet hose canbe kept onthe tap toprevent

damaging the fixingscrew.

1.Push down theslider. Insert the

water inlet hoseinto the jointer.

2.Hang the locklever to the jointer.

Release the slidertill a click

sound is heard.

Locking lever

Slider

Water absorption cushion

Nut of the water inlet hose

Jointer of thewater inlet valve

Slider

Jointer of thewater

inlet hose

Locking lever

Connection between the water inlet hose and the

washing machine

Connection between the jointer of the water inlet

hose and the water inlet hose

Check the connection between the jointer of the

water inlet hose and the water tap

Take down the water inlet hose

1.Swaying the hosegently to confirmif it isfastened stable.

2.After installation, openthe tap tocheck if itleaks.

3.Do not bendthe hose withoverstrain.

4.Before each usageplease check if

the connection betweenthe jointer

of the waterinlet hose and the water

tap, and theinstallation of the

water inlet hoseare firm, so as to

prevent dropping fromimproper

Installation position.

1.Preparation before washing

Preparation before washing

1.Connect the water inlet hose

2.Confirm that the washing machine is earthed reliably.Then

insert the power plug into the receptacle.Do not connect

the earth terminal to the gas pipe and tap water pipe.

3.Hang up the drain hose.

4.Slanting or uneven

ground may result

in unstable working

or abnormal noise.

Please make the

machine stand horizontally.

Pay attention to followings before washing the laundries

Confirm if

there's

special

requirement

for the

laundries.

Clear the

pocket.

Take out the

coins ,

sand, hairpins

etc.

Fasten the

buttons and

zippers.

When the pulsator

is running ,the

buttons of the

laundries may

cause noise. For

the sake of discretion,

please put the

laundries with

buttons into other

laundries.

The quantity of

the laundries

shall not exceed

the rated value.

The big laundries

like the jeans

shall be put in

loosely.

a. Check if the laundries are applicable for washing with machine.

b. Divide the laundries with unfast color from other laundries.

c. Put those laundries difficult to absorb water into water with hand.

d. For those laundries with heavy soil, please first remove the dirt like mud or dust.

For the parts with heavy soil, please apply detergent in advance, which can make it

easier to remove the soil.

e. For those laundries that may get lint ball and those with long fur, turn it over before

putting in.

f. Do not put those laundries polluted by chemicals directly into the washing machine.

For those small laundries and those may get twisting or worn, and woolen/fur

laundries, please put them into mesh bag for washing.

0.8m H 1.2m

Otros manuales para HWM80-0528

Tabla de contenidos

Otros manuales de Arandela de Haier

Haier

Haier HWM85-9288 Manual de usuario

Haier

Haier HW70-1001 Manual de usuario

Haier

Haier JW-PK90A Manual de usuario

Haier

Haier HLT23E - 07-04 Manual de usuario

Haier

Haier HWM120-35FF Manual de usuario

Haier

Haier 650 Manual de usuario

Haier

Haier JW-G50C Manual de usuario

Haier

Haier HW70-IM10829TNZP Manual de usuario

Haier

Haier Thermocool HMS1000TVE Manual de usuario

Haier

Haier HSW-70S1 Manual de usuario

Haier

Haier HWF95AN1 Manual de usuario

Haier

Haier HW120-BP14959S8 Manual de usuario

Haier

Haier HWT60FVW2 Manual de usuario

Haier

Haier HW50-1010 Guía

Haier

Haier HWM80-0566 Manual de usuario

Haier

Haier GWT480BW Manual de usuario

Haier

Haier WD9900 Manual de usuario

Haier

Haier SAW-9105 Manual de usuario

Haier

Haier HWM120-0523S Manual de usuario

Haier

Haier JW-K60A Manual de usuario

Haier

Haier HWM70-1203D Manual de usuario

Haier

Haier HLP22P - 06-03 Manual de usuario

Haier

Haier HW80-B14979 Manual de usuario

Haier

Haier HNS1260TVE Manual de operación y mantenimiento

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario