Haier GDZ5-1 Manual de usuario

HAIER

Front Loading Dryer

Service Manual

PART # WD-8888-22

HAIER AMERICA TRADING, LLC

www.haieramerica.com

Table Of Contents

Features 3

Specifications 4

Safety Caution 5

Unpacking And Installation 7

Troubleshooting 8

Dimensions 11

Names Of Parts 11

Circuit Wiring 12

Features

●Three drying cycle, heat cool and synthetic.

●The support of front and rear make running balanced low noise.

●Straight exhaust of back-inhale styled make good airproof and

high drying efficiency.

●After heat drying cool may protect clothes.

Specifications

Models

GDZ5-1

Capacities

Capacities 11lb

Drum size 117L 2800rpm 220-240v/50Hz

Motor size (hp) 250W/150W

Features

Type Direct Exhaust

Controls Mechanism

Temperature Settings 3 kinds

Dry Sensor No

Reversible Door No

End of Cycle Signal No

Wrinkle Remover Tumble No

Easy Access Lint Filter Yes

Interior Drum Light No

Dryer Rack No

Easy Opening Wide Door 10.6inch

Dry Cycles 2 kinds

Fabric Care Drying Cycles Temperature Aegis

Permanent Press No

Side Exhaust Vents No

LP Conversion Kit

Serviceable Front Rear End

Dimensions

Width 23.4inch

Depth with Door Close 22.8inch

Depth with Door Open 36.6inch

Height

Height with Back Guard 33.8inch

Shipping Weight (lbs) (approx.) 94.7lb

Safety Precautions

WARNING! To reduce the risk of fire, electrical shock, or injury to persons when

using this dryer, comply with the basic warnings listed below.

WARNING! Failure to comply with these warning could result in serious

personal injuries or damage to the dryer.

WARNING! Do not dry items that have been previously cleaned in, soaked in,

or spotted with gasoline, cleaning solvents, kerosene, cooking oils, waxes, etc.

Do not store these items on or near the dryer. These substances give off vapors

that could ignite or explode.

WARNING! To prevent fire, do not use heat to dry items containing plastic,

foam rubber or similarly textured rubber-like materials, or items containing

feathers or down.

WARNING! Clean the lint screen before or after each load. The interior of the

dryer, lint screen housing and qualified service personnel should clean exhaust

duct approximately every 18 months. An excessive amount of lint build-up in

these areas could result in inefficient drying and possible fire. See care and

cleaning.

WARNING! Do not operate the dryer if the lint screen is blocked, damaged or

missing. Fire hazard, overheating and damage to fabrics can occur.

WARNING! Keep area around the exhaust opening and surrounding areas free

from the accumulation of lint, dust and dirt.

WARNING! Do not obstruct the flow of ventilating air. Do not stack or place

laundry or throw rugs against the front or back of the dryer.

Important Safety Precautions

WARNING! Do not spray any type of aerosol into, on, or near dryer at any time.

WARNING! Do not use fabric softeners or products to eliminate static unless

recommended by the manufacturer of the fabric softener or product.

WARNING! Do not allow children to play on or in the dryer. Close supervision of

children is necessary when the dryer is used near children. As children grow,

teach them the proper, safe use of all appliances.

WARNING! Destroy the carton, plastic bag and other packing materials after

the dryer is unpacked. Children might use them for play. Cartons covered with

rugs, bedspreads or plastic sheets can become airtight chambers.

WARNING! Keep laundry products out of children’s reach. To prevent personal

injury, observe all warnings on product labels.

WARNING! Before the dryer is removed from service or discarded, remove the

dryer door to prevent accidental entrapment.

WARNING! To prevent shock hazard and assure stability during operation, the

dryer must be installed and electrically grounded by a qualified service person in

accordance with local codes. Installation instructions are packed in the dryer for

the installer’s reference. Refer to" INSTALLATION INSTRUCTIONS" for detailed

grounding procedures. Never ground the dryer to a gas pipe. If the dryer is

moved to a new location, have it checked and reinstalled by a qualified service

person.

WARNING! Always disconnect the dryer from the electrical supply before

attempting any service or cleaning. Failure to do so can result in electrical shock

or injury.

WARNING! Do not use any type spray cleanser when cleaning dryer interior.

Hazardous fumes or electrical shock could occur.

WARNING! To prevent injury, do not reach into the dryer if the drum is moving.

Wait until the dryer has stopped completely before reaching into the drum.

WARNING! To prevent injury and damage to the dryer:

●All repairs and servicing must be performed by an authorized servicer unless

specifically recommended in this Owner’s Guide. Use only authorized factory

parts.

●Do not tamper with controls.

●Do not install or store the dryer where it will be exposed to the weather.

Unpacking and Installation

1. Open the package, check against the instruction manual to see if the spare

parts are complete.

2. Put the dryer to the location required by the user (balcony, kitchen, toilet or

living room). According to the condition of the installation position, give the user

advices on whether an exhaust pipe is used or not.

The following cases should be dealt with in different ways

a. If there is an exhaust outlet at the mounting position, connect the exhaust pipe

to the outlet to facilitate exhaust of the indoor humid and hot air. The mounting

procedure is as follows:

1) Mount the connecting sleeve of the exhaust pipe onto the rear exhaust vent of

the dryer.

2) Connect the extension pipe to the connecting sleeve, and fix with pipe clips.

3) Pull the extension pipe to connect it with the exhaust outlet.

b. If there is no exhaust outlet at the mounting position, it is recommended not to

mount an extension pipe, but a space of at least 3.9inch at the dryer back should

be left to facilitate air exhaust.

c. An extension pipe can be mounted at the request of the user according to the

above steps. The dryer should be near the window, through which the user pulls

the extension pipe to exhaust the humid and hot air in the room. At the end of the

use, replace the extension pipe.

d. At the request of the user, make a hole in the wall to mount the extension pipe

(hole diameter 3.9-4.2inch). Not more than 4 bends should be made for the

extension pipe (more bends will cause difficulty to exhaust and affect the drying

efficiency).

3. The dryer body should be level. Adjust it with foot-adjusting spanner.

4. Close the dryer door, set the timer pointer into the red zone, and switch on the

power to operate for 2-3 minutes. If the back guard plate is hot, it means the

operation is normal. Push down the dryer button, if the dryer indicator is on, it

means the operation is normal. Turn off the power, adjust the timer pointer into

the blue zone, and then turn on the power again. If the cold air indicator (strainer

indicator) is on, it means the operation is normal.

Troubleshooting

A. The power light is on, but the machine does not work after a program is

set.

a. Check the micro switch. If it is out of order, replace it; otherwise, check to see

if it is closed or it is open, check the switch arm height and adjust it.

Maintenance Procedure:

1) Loosen the screws on the deck plate at the back to remove the deck plate,

unplug the micro switch power line in the front channel.

2) Hold the exposed part of the micro switch and move it toward the drum, rotate

the switch arm and take out the micro switch carefully.

3) If the switch is out of order, replace it; otherwise, it means the switch arm

height is too low, raise it and re-mount it.

b. If the micro switch is ok, i.e. it closes after the door is closed, check the

program controller.

Replace it if it does not work.

Maintenance Procedure:

1) Loosen the screws on the deck plate at the back and remove the deck plate.

2) Take out the timer knob, unscrew the timer with a screwdriver and pull out the

timer connecting wire.

3) Replace the timer and turn on the power. If the dryer operates normally, mount

the deck plate.

B. The program knob of the dryer points at the red zone, the cold air

indicator is not the drum rotates, but heating and drying operation is not

available, and the back guard plate is not warm.

The fuse is turned off.

Check Procedure: In checking Procedure, pull out the plugs at both ends and

measure the fuse with an AVO meter. If it is not in order, replace it.

C. The program knob of the dryer points at the red zone, the cold air

indicator is on and the drum rotates, but heating and drying operation is

not available, and the back guard plate is not warm.

1) The overheat temperature controller of the heating component is turned off.

Maintenance Procedure

Remove the back guard plate, check to see if the high-temperature thermostat is

in order.

Check Procedure: Take down the cable plug and measure the high-temperature

thermostat with an AVO meter to see if it is correct. Replace it if it is in trouble.

2) If there is no heating operation after the above steps, open the back cover to

check if the low temperature thermostat on the case is in order.

Checking Procedure: The same as the check procedure for the high-temperature

thermostat.

3) If no abnormalities are found after the above steps, it means the heating pipe

has trouble, replace it.

Maintenance Procedure:

1) Open the back cover and disconnect the heating pipe.

2) Loosen the left and right air deflectors and remove the heater; then pull out the

power line of the heating pipe from its location hole.

3) Replace the heater, and then turn on the power and check the heater. If the

operation is normal, mount the back cover again.

D. The program knob of the dryer points at the blue zone, the cold air

indicator is on and the drum rotates

The fuse is turned off.

E. After a program is selected and the dryer is started, the exhaust system

works (operational sounds can be heard), but the drum does not rotate.

The lobed belt is worn off seriously; replace it.

F. Great operating noise is heard accompanied by abnormal noises; after

opening the back cover and removing the belt, the noise disappears.

a. Bearing damage

Maintenance Procedure

a. Remove the back cover and loosen the bearing holder with a screwdriver.

Check the bearing. If it has trouble, remove it with a minus screw driver and

replace.

b. If the bearing is ok, remove the belt and rotate the motor; if the noise

disappears, it means the drum holder is worn off seriously, replace it.

Maintenance Procedure

1) Open the deck plate, pull out the power line terminal, then open the back

cover and remove the belt, pull out the power line terminal of the heater and

remove the back cover.

2) Unscrew the drum holder on the front channel with a screwdriver and replace

it.

3) Reinstall the dryer (the drum inner wall at the drum inlet must press on the

drum holder, and the drum holder can be touched after the door is opened;

otherwise the installation is not proper). Check to see if the dryer operation is

normal according to the above procedure.

G. Great operating noise is heard, accompanied by abnormal noises. After

opening the back cover and removing the belt, the noise still exists.

Impeller falls off or is damaged.

Maintenance Procedure

1) Open the back cover and remove the belt; pull out the power line clip and

power adapter of the heater; then unplug the motor and tip the dryer.

2) Unscrew the base plate and remove it, open the end cover of the case and

check the impeller.

Refasten or replace the bad impeller and re-install the dryer.

Otros manuales para GDZ5-1

Tabla de contenidos

Otros manuales de Secadora de Haier

Haier

Haier T60-32 Manual de usuario

Haier

Haier GE GFD14ESSNWW Cómo utilizar

Haier

Haier HDY-D70-E Manual de usuario

Haier

Haier GDG900AW Manual de usuario

Haier

Haier GDZ5-1 Manual de usuario

Haier

Haier HD80-79 Manual de usuario

Haier

Haier TCD60E Manual de usuario

Haier

Haier HLTD500ACW Manual de usuario

Haier

Haier HD90-A2979 Manual de usuario

Haier

Haier HDY60M Manual de usuario

Haier

Haier HDY6-1 Manual de usuario

Haier

Haier HDY-C70 HA AA Manual de usuario

Haier

Haier HLF11P Manual de usuario

Haier

Haier HD90-A3Q979U1 Manual de usuario

Haier

Haier Ginesis HLF103Q Manual de usuario

Haier

Haier GDZ3.5-1 Manual de usuario

Haier

Haier GDZ22-1 Manual de usuario

Haier

Haier HDY60 HA AA Manual de usuario

Haier

Haier GDZ5.0-61WH HA AA Manual de usuario

Haier

Haier GDZ5.0-1 Manual de usuario

Haier

Haier HD80-A2939 Manual de usuario

Haier

Haier QFD15 Series Instrucciones originales

Haier

Haier Ginesis HLF103Q Manual de usuario

Haier

Haier GDG480BW Manual de usuario

Manuales populares de Secadora de otras marcas

Bosch

Bosch WTA79200GB Manual de usuario

Amana

Amana W10233410A Manual de usuario

Miele

Miele TWH 780 WP Manual de usuario

Asko

Asko T760 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manual de usuario

Bosch

Bosch Logixx 10 WTB76556GB Hoja de especificaciones

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manual de instrucciones

Electrolux

Electrolux EW2H328R2 Manual de usuario

Beko

Beko DS8433RX1M Manual de usuario

Dawlance

Dawlance Spinner DS 6000 C Manual de usuario

Electrolux

Electrolux TP5080TW Manual de usuario

AEG

AEG TR838P4OB Manual de usuario

Indesit

Indesit IDV 75 Manual de usuario

Infiniton

Infiniton SD-DG85C Manual de usuario

BOMANN

BOMANN WT 5019 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Manual de usuario

Asko

Asko T793C Manual de usuario

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario