Hach Orbisphere 51 Series Manual rápido

DOC024.98.93134

ORBISPHERE Model 51x

Analyzer with K-M1100 and TC

Sensors

11/2017, Edition 2

Basic User Manual

Allgemeines Benutzerhandbuch

Manuel d'utilisation de base

Manual básico del usuario

Základní uživatelská příručka

Alapvető felhasználói kézikönyv

Основно ръководство за потребителя

English..............................................................................................................................3

Deutsch.......................................................................................................................... 29

Français......................................................................................................................... 58

Español.......................................................................................................................... 87

Čeština......................................................................................................................... 115

Magyar......................................................................................................................... 143

български................................................................................................................... 171

Specifications

Specifications are subject to change without notice.

Analyzer

Specification Details

Operating temperature –5 to 50°C (23 to 122 °F)

Storage temperature –20 to 70°C (–4 to 158 °F)

Operating humidity 0 to 95% non condensing relative humidity

Operating altitude From 0 to 2,000 m. (6,550 ft.) above sea level

EMC requirements EN61326-1: EMC Directive

Note: The wall mount instrument is a Class A product. In a domestic environment this product

may cause radio interference in which case the user may be required to take adequate

measures.

Korean registration

User Guidance for EMC Class A Equipment

업무용을 위한 EMC 등급 A 장치에 대한

사용자 지침

사용자안내문

A 급 기기 ( 업무용 방송통신기자재 )

이 기기는 업무용 (A 급 ) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의

하시기 바라며 , 가정외의 지역에서 사용하는 것을 목적으로 합니다.

CE compliance EN61010-1: LVD Directive

Safety rating ETL, conforming to UL 61010-1 and CSA 22.2 No. 61010-1

Enclosure ratings IP 65; Totally protected against dust; Protected against low pressure jets of water

from all directions.

NEMA 4X (wall mount only); Totally protected against dust; Protected against

pressure jets of water from all directions.

WARNING

Enclosure rating does not apply to external power supply for benchtop

instruments.

Power supply Universal 100 VAC to 240 VAC @ 50/60 Hz - 40VA; 10 to 30 VDC - 30W

Analog current output version

on the measurement

board(s)

4-20 mA (default) or 0-20 mA (configuration with software);

3 configurable outputs: Maximum load: 500 ohm; Sensitivity: 20μA;

Accuracy: ± 0.5% (between operating temperature limits)

Analog voltage output

version on the measurement

board(s)

0- 5 V output (hardware option);

3 configurable outputs; Minimum load: 10 KOhm; Sensitivity: 5 mV;

Accuracy: ± 0.5% (between operating temperature limits)

Measurement alarm relays

on the measurement

board(s)

Three alarm relays per measurement board; 1A-30 VAC or 0.5A-50 VDC on a

resistance load.

Configurable to Normally Open [NO] or Normally Closed [NC] contacts by

changing the jumper positions.

WARNING

Potential Electrocution Hazard. Connect only safety low voltage < 33 VAC

RMS

English 3

Specification Details

System alarm relay on the

main board

One system alarm relay; 1A-30 VAC or 0.5A-50 VDC on a resistance load.

Normally closed [NC] (NO relay also available) when instrument is turned on.

WARNING

Potential Electrocution Hazard. Connect only safety low voltage < 33 VAC

RMS

Thermal cut off Prevents ageing of sensors when exposed to high temperatures

Options USB host; Ethernet 10/100 Base-T

Wall and pipe mount

instrument

(H x D x W)

236.5 x 160 x 250 mm; Weight 4.25 kg

9.31 x 6.30 x 9.84 in.; Weight 8.82 lbs

Panel mount instrument

(housing) (H x D x W)

156 (123) x 250 x 220 (214) mm; Weight 3.35 kg

6.14 (4.84) x 9.84 x 8.86 (8.43) in.; Weight 6.62 lbs

K-M1100 sensor

Specification Details

Sample temperature Measurement from –5 to 50°C (23 to 122°F)

Sensor resistant to temperature from –5 to 100°C (23 to 212°F)

Sample pressure 1 to 20 bar absolute (14.5 to 290 psia)

Sample flow rate

requirement

50 to 300 mL/min

Sample types K1100 sensor: Water only

M1100 sensor (low range): Water and beer

M1100 sensor (high range): Water, beer, wine, wort and carbonated drinks

For oxygen measurement

liquid phase gas phase

Measurement range Low range sensors 0 to 2000 ppb (dissolved.

Indicative values until

5000 ppb)

0 to 50 mbar or 0 to 5% O2 (at

atm pressure)

High range sensors 0 to 40 ppm (dissolved) 0 to 1 bar or 0 to 100% O2 (at

atm pressure)

Repeatability Low range sensors ± 0.4 ppb or 1%,

whichever is the greater

± 0.01 mbar or 10 ppm gas or

1%, whichever is the greater

High range sensors ± 0.015 ppm or ± 2%,

whichever is the greater

± 0.4 mbar or 400 ppm gas or

2%, whichever is the greater

Reproducibility Low range sensors ± 0.8 ppb or 2%,

whichever is the greater

± 0.02 mbar or 20 ppm gas or

2%, whichever is the greater

High range sensors ± 0.02 ppm or ± 3%,

whichever is the greater

± 0.5 mbar or 500 ppm gas or

3%, whichever is the greater

Accuracy Low range sensors ± 0.8 ppb or 2%,

whichever is the greater

± 0.02 mbar or 20 ppm gas (at

atm pressure) or 2% of

reading, whichever is the

greater

High range sensors ± 0.02 ppm or ± 3%,

whichever is the greater

± 0.5 mbar or 500 ppm gas (at

atm pressure) or 3% of

reading, whichever is the

greater

4 English

Specification Details

Limit of detection

(LOD)

Low range sensors 0.6 ppb 0.015 mbar or 15 ppm gas (at

atm pressure)

High range sensors 0.015 ppm 0.4 mbar or 400 ppm gas (at

atm pressure)

Response time

(90%)

Low range sensors < 30 seconds < 10 seconds

High range sensors < 50 seconds < 10 seconds

Display resolution High and low range sensors 0.1 ppb 0.001 mbar or 1 ppm gas

Calibration Low range sensors: Single point calibration (zero)

High range sensors: Two at cap replacement (zero and air), one during use (air)

Calibration sample Low range sensors: Standard 99.999% N2 (quality 50) or equivalent oxygen free gas

High range sensors: Standard 99.999% N2 (quality 30) or equivalent oxygen free gas, air

M1100 12 mm (PG

13.5) sensor (L x W)

246 x 47 mm - weight 0.6 kg

9.69 x 1.85 in. - weight 1.32 lbs

K1100 and

M1100 28 mm

sensor (L x W)

143.50 x 49 mm - weight 0.74 kg

5.65 x 1.93 in. - weight 1.63 lbs

Calibration device Weight 0.7 kg

TC sensor

Sensor type

31 250 H2, 31260 H2 and 31290 (purge gas N2)

For other purge gases, please contact your Hach

representative for specification.

31 550 N2, 31560 N2

and 31590 (purge

gas CO2)

Specification Membrane 29561A Membrane 2952A Membrane 2935A Membrane 29561A

Thickness [μm] 25 25 25 25

Material PFA ETFE ECTFE (Halar) PFA

Recommended

applications

Waste gas offgas,

reactor coolant Reactor coolant High H2 level In-line beverage

Radiation limits 105 rad 108 rad 108 rad 105

Measurement range

at 25°C

0-2 ppm, or

0-25 cc/kg, or

0-1.5 bar

0-10 ppm, or

0-120 cc/kg, or

0-6 bar

0-20 ppm, or

0-220 cc/kg, or

0-12 bar

0-350 ppm, or

0-300 mL/L, or

0-20 bar

Accuracy (sample

temperature 20-50°C

within ± 5°C of

calibration

temperature)

The greater of ±1%

of reading or ±

2 ppb, or ±

0.03cc/kg, or ±

1.5 mbar

The greater of ±1%

of reading or ±

8 ppb, or ± 0.1cc/kg,

or ± 6 mbar

The greater of ±1%

of reading or ±

25 ppb, or ±

0.4 cc/kg, or ±

20 mbar

The greater of ±2%

of reading or ±

0.3 ppm, or ±

0.25mL/L, or ±

15 mbar

Accuracy (sample

temperature 0-50°C

independent of

calibration

temperature)

The greater of ±3%

of reading or ±

15 ppb or ±

0.18 cc/kg or ±

6 mbar

The greater of ±3%

of reading or ±

60 ppb or ±

0.6 cc/kg, or ±

20 mbar

The greater of ±3%

of reading or ±

150 ppb or ±

2.5 cc/kg, or ±

50 mbar

The greater of ±4%

of reading or ±

1 ppm or ± 0.8 mL/L

or ± 34 mbar

Measurement cycle

(seconds) 17 22

English 5

Sensor type

31 250 H2, 31260 H2 and 31290 (purge gas N2)

For other purge gases, please contact your Hach

representative for specification.

31 550 N2, 31560 N2

and 31590 (purge

gas CO2)

Specification Membrane 29561A Membrane 2952A Membrane 2935A Membrane 29561A

Sample flow rate1

(through flow

chamber)

220 mL/min 200 mL/min 100 mL/min 300 mL/min

Linear flow rate2

(past sensor socket) N/A N/A N/A 150 cm/sec

Purge gas pressure regulator

Specification Details

Model 29089S4 (0.25 in.), 29089S6 (6 mm)

Filtration grade 40 μm

Input pressure min/max 1 bar / 16 bar

Output pressure min/max 0.5 bar / 7 bar

Standard nominal flow rate 900 Liters/minute

Condensate volume 22 cm3

Temperature range (ambient and media) -10°C to 60°C

Purge gas dew point -10°C (+14°F)

Construction materials Housing: metal; Condensate bowl: polycarbonate; Bowl guard: metal

Weight 460 g.

Dimension in cm (overall) 21 x 11.5 x 8

Expanded manual version

For additional information, refer to the expanded version of this manual, which is available on the

manufacturer's website.

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

1Minimal flow through an ORBISPHERE 32001 flow chamber

2Minimal flow past an ORBISPHERE 29501 sensor socket

6 English

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

This is the safety alert symbol. Obey all safety messages that follow this symbol to avoid potential

injury. If on the instrument, refer to the instruction manual for operation or safety information.

This symbol indicates that a risk of electrical shock and/or electrocution exists.

This symbol indicates the presence of devices sensitive to Electro-static Discharge (ESD) and

indicates that care must be taken to prevent damage with the equipment.

This symbol, when noted on a product, indicates the instrument is connected to alternate current.

Electrical equipment marked with this symbol may not be disposed of in European domestic or

public disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no

charge to the user.

Products marked with this symbol indicates that the product contains toxic or hazardous substances

or elements. The number inside the symbol indicates the environmental protection use period in

years.

Operating altitude

This instrument is rated for an altitude of 2000 m (6562 ft) maximum. Use of this instrument at an

altitude higher than 2000 m can slightly increase the potential for the electrical insulation to break

down, which can result in an electric shock hazard. The manufacturer recommends that users with

concerns contact technical support.

English 7

Installation

This section provides necessary information to install and connect the analyzer. The installation of

the analyzer should be performed in accordance with relevant local regulations.

D A N G E R

Electrocution hazard. Do not connect AC power directly to a DC powered instrument.

D A N G E R

Electrocution hazard. Always remove power to the instrument before making electrical connections.

D A N G E R

Electrocution hazard. If this equipment is used outdoors or in potentially wet locations, a Ground Fault

Circuit Interrupt (GFCI/GFI) device must be used for connecting the equipment to its main power

source.

WARNING

Potential Electrocution Hazard. A protective earth (PE) ground connection is required for both

100-240 VAC and 5 VDC wiring applications. Failure to connect a good PE ground connection can

result in shock hazards and poor performance due to electromagnetic interferences. ALWAYS connect

a good PE ground to the controller terminal.

CAUTION

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

N O T I C E

Install the device in a location and position that gives easy access to the disconnect device and its operation.

N O T I C E

Potential Instrument Damage. Delicate internal electronic components can be damaged by static electricity,

resulting in degraded performance or eventual failure.

Wall mounting

1. Attach the U-bracket (provided) to the wall with two screws (not

provided).

2. Tilt the instrument slightly backwards to align the bracket pins and

the insertion slots, and slide the instrument onto the bracket as

shown.

3. Insert the 2 locking screws with washers through the side slots.

4. Adjust the instrument angle for better screen vision, and lock both

side screws.

8 English

Pipe mounting

1. Assemble the pipe mount bracket to the U-bracket, using the two screws provided.

2. Attach this assembly to the pipe using two clamps (not provided).

3. Slide the instrument onto the bracket.

4. Insert the 2 locking screws with washers through the side slots.

5. Adjust the instrument angle for better screen vision, and lock both side screws.

Panel mounting

WARNING

Electrocution hazard. If the cable and connector for the power supply are not accessible after

installation, an accessible local disconnection means for the instrument power is mandatory.

1-3 4-5 6-7

1. Cut an opening in the panel to accommodate the bracket frame provided.

2. Install the provided frame in the opening.

3. Fold the 6 tabs over the panel lips, using adjustable joint pliers.

4. Slide the instrument in the bracket frame. The instrument should go over the four "T" pins. Rotate the 4 fast

locking screws on both sides of the front panel and slide it in.

5. Rotate the 4 fast locking screws 1/4 turn twice in the lock direction as indicated on the side of the front panel.

This locks the instrument in place on the four "T" pins.

6. To access the connections inside the instrument, remove the instrument housing (six screws on the back

panel, and slide the housing back out)

7. Pass the cables through the housing, then through the cable gland (if applicable) and then perform the

connections as detailed below.

English 9

Instrument connections

Figure 1 Connections - panel (left); wall/pipe (right)

1 Power cable 6 K-M1100 Sensor connection

2 Ethernet cable gland 7 External pressure sensor connection

3 USB-A host connector 8 Input/Output 2 cable gland

4 USB-B 4-pin connector 9 TC Sensor connection

5 Input/Output 1 cable gland 10 Keylock (wall/pipe mount only)

Connection to mains power supply

Power supply connection (low voltage instruments)

For low voltage instruments (10-30 VDC), connection to the mains power supply is with a 8-pin

BINDER connector (supplied).

Note: The connectors are grooved to avoid an incorrect fitting to the instrument.

Connect the power cable to the connector as follows:

Figure 2 BINDER connector Pin Connections:

1. Power 10-30 VDC

2. Ground

3. Ground

4. Ground

5. Not used

6. Power 10-30 VDC

7. Power 10-30 VDC

8. Earth

Figure 3 Wiring side view

Power supply connection (high voltage instruments)

D A N G E R

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

10 English

Otros manuales para Orbisphere 51 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de Hach

Hach

Hach sensION+ MM150 Manual de usuario

Hach

Hach POCKET COLORIMETER II Manual de usuario

Hach

Hach Polymetron 9586 Manual de usuario

Hach

Hach POLYMETRON 9135 Manual de usuario

Hach

Hach sensION+ DL Manual de usuario

Hach

Hach CLF10sc Manual de usuario

Hach

Hach LANGE LOC 100 Manual de usuario

Hach

Hach APA 6000 Manual de usuario

Hach

Hach ANATEL PAT700 Manual de usuario

Hach

Hach 1720E Manual de usuario

Hach

Hach H160 Manual de usuario

Hach

Hach MTC101 Manual de usuario

Hach

Hach BioTector B7000i Manual de usuario

Hach

Hach LPV445.99.09110 Manual de usuario

Hach

Hach NA5600 sc Na+ Manual de usuario

Hach

Hach TU5300 sc Manual rápido

Hach

Hach DR2400 Manual de usuario

Hach

Hach sensION+ pH3 Manual de usuario

Hach

Hach PLATINUM Series Manual de usuario

Hach

Hach IntelliCAL ISENH3181 Series Manual de usuario

Hach

Hach TL2310 Manual rápido

Hach

Hach NA5600 sc Na+ Manual de instrucciones

Hach

Hach sensION+ pH1 Manual de usuario

Hach

Hach TU5200 Manual rápido

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario