HACH LANGE TU5400 sc Manual rápido
DOC023.52.90501
TU5400 sc/TU5300 sc
09/2014, Edition 1
Basic User Manual
-BETA DRAFT-
BETA
-BETA DRAFT-
BETA
Table of contents
Specifications on page 3 Calibration on page 17
General information on page 4 Maintenance on page 17
Installation on page 10 Troubleshooting on page 22
Startup on page 17
Additional information
Additional information is available on the manufacturer's website.
Specifications
Specifications are subject to change without notice.
Specification Details
Measurement method 90-degree nephelometry collected at 360-degrees about the axis of the
incident light beam
Primary compliance method USEPA
Optical light source 650 nm, maximum 1 mW laser
Laser Class 2 laser product: contains an embedded non user-serviceable class
2 laser
Measurement units TU5300 sc: NTU, FNU, TE/F, FTU, EBC; TU5400 sc: NTU, FNU, TE/F, FTU,
EBC, mNTU
Range 0 to 700 NTU
Stray light <0.010 NTU
Accuracy ± 2% of reading plus 0.01 NTU from 0 to 40 NTU
± 10 % of reading from 40 to 700 NTU based on formazin primary standard
Linearity Better than 1% for 0 to 40 NTU on formazin at 25 °C (77 °F). Allows for
accurate calibration at 20 NTU
Repeatability Better than 1% of reading or ± 0.002 NTU on formazin at 25 °C (77 °F),
whichever is more
Signal average time 5 to 90 seconds (default: 30 seconds)
Air bubble compensation Physical, mathematical (default: on)
Detection limit TU5300 sc: 0.003 NTU, TU5400sc: 0.0003 NTU
Response time T90 < 30 seconds at 100 mL/minute (without bubble trap, signal average time:
off)
T90 < 3 minutes at 100 mL/minute (with bubble trap, signal average time: off)
Sample pressure 6 bar (87 psi) maximum, compared to air at sample temperature range from
2 to 40 °C (35.6 to 104 °F)
3 bar (43.5 psi) maximum compared to air at temperature range from 40 to
70 °C (104 to 158 °F)
Sample flow rate 100 to 1000 mL/min; optimal flow rate: 200 to 500 mL/min
Sample temperature 2 to 70 °C (35.6 to 158 °F)
Sample salt content Up to 65 g/L
English 3
-BETA DRAFT-
BETA
Specification Details
Calibration options StablCal®: at 20 NTU from 0 to 40 NTU; at 20 NTU and 600 NTU for full
range
User prepared formazin: at 20 NTU from 0 to 40 NTU; at 20 NTU and 600
NTU for full range
Custom calibration for up to 6-point calibrations
Verification options Liquid: StablCal®, formazin (0.1 to 40 NTU)
Dry: factory-set values of 1.0 ± 25% NTU
Verification (Link2SC software) Verfication of the measurement value to compare values to a laboratory
instrument via Link2sc software
Dimensions (W x D x H) 268 x 249 x 190 mm (10.6 x 9.8 x 7.5 in.)
Enclosure Rating: NEMA/IP65 for functional units
Material: ASA Luran S 777K / RAL7000, TPE RESIN Elastocon® STK40,
Thermoplastic Elastomer TPS-SEBS (60 Shore)
Display resolution 0.0001 NTU (0.0001 to 0.9999/1.000 to 9.999/10.00 to 99.99/100.0 to
700 NTU)
Default=TU5300sc: 0.001 NTU, TU5400sc: 0.0001 NTU
Sensor cable length 1.6 m (5.25 ft), extendable up to 50 m (164 ft) for instrument without
accessories
Fittings Sample quick connector: ¼-in. for ¼-in. tubing
Tubing Materials: Polyethylene, polyamide or polyurethane tubing, calibrated outside
diameter ¼ in. +0.001 / –0.004 in. or +0.03 mm / –0.1 mm
Weight ???
Installation environment Indoor or outdoor with cover
Mounting Wall
Protection class III
Pollution degree/installation
category
2, II
Power requirements 12 VDC, 14 VA from the sc controller. Refer to the controller documentation
for the controller power requirements.
Operating temperature 0 to 50 °C (32 to 122 °F)
Storage temperature –40 to 60 °C (–40 to 140 °F)
Operating humidity Relative humidity: 5 to 95% at different temperatures, non-condensing
Certifications CE compliant; US FDA accession number: 1420493-xxx. This product
complies with IEC/EN 60825-1 and to 21 CFR 1040.10 in accordance with
Laser Notice No. 50.
Warranty 1 year (EU: 2 years)
General information
In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential
damages resulting from any defect or omission in this manual. The manufacturer reserves the right to
make changes in this manual and the products it describes at any time, without notice or obligation.
Revised editions are found on the manufacturer’s website.
4 English
-BETA DRAFT-
BETA
Safety information
N O T I C E
The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,
without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent
permitted under applicable law. The user is solely responsible to identify critical application risks and install
appropriate mechanisms to protect processes during a possible equipment malfunction.
Please read this entire manual before unpacking, setting up or operating this equipment. Pay
attention to all danger and caution statements. Failure to do so could result in serious injury to the
operator or damage to the equipment.
Make sure that the protection provided by this equipment is not impaired. Do not use or install this
equipment in any manner other than that specified in this manual.
Use of hazard information
D A N G E R
Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
Indicates a potentially hazardous situation that may result in minor or moderate injury.
N O T I C E
Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special
emphasis.
Precautionary labels
Read all labels and tags attached to the instrument. Personal injury or damage to the instrument
could occur if not observed. A symbol on the instrument is referenced in the manual with a
precautionary statement.
Electrical equipment marked with this symbol may not be disposed of in European domestic or public
disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no charge to
the user.
This symbol, if noted on the instrument, references the instruction manual for operation and/or safety
information.
This symbol indicates that a risk of electrical shock and/or electrocution exists.
This symbol indicates the need for protective eye wear.
This symbol indicates a laser device is used in the equipment.
English 5
-BETA DRAFT-
BETA
This symbol identifies a risk of chemical harm and indicates that only individuals qualified and trained
to work with chemicals should handle chemicals or perform maintenance on chemical delivery
systems associated with the equipment.
This symbol indicates radio waves.
Class 2 laser product
D A N G E R
Personal injury hazard. Never remove covers from the instrument. This is a laser-based instrument and
the user risks injury if exposed to the laser.
Class 2 laser product, IEC60825-1:2007, 650nm/max. 1,0 mW
Location: Rear of the instrument.
Conforms to U.S. regulations 21 CFR 1040.10 and 1040.11 in accordance with
Laser Notice No. 50.
Location: Rear of the instrument.
Caution—Class 2 laser radiation when the lid is open. Do not look into the
laser beam.
Location: Top of the vial compartment.
This instrument is a Class 2 Laser product. There is only visible laser radiation when the instrument
is defective and when the instrument lid is open. This product complies with EN 61010-1, "Safety
Requirements for Electrical Equipment for Measurement, Control and Laboratory Use" and with
IEC/EN 60825-1, "Safety of Laser Products" and with 21 CFR 1040.10 in accordance with Laser
Notice No. 50. Refer to the labels on the instrument that supply laser information.
RFID module
An optional RFID module is available for this instrument. RFID technology is a radio application.
Radio applications are subject to national conditions of authorization. The use of the sensor is
currently permitted in the following countries: EU. The manufacturer advises that the use of the
sensor outside of the above-mentioned regions may contravene national laws. The manufacturer
reserves the right also to obtain authorization in other countries. In case of doubt, contact the
manufacturer.
The sensor contains an RFID module to receive and transmit information and data. The RFID
module operates with a frequency of 13.56 MHz.
6 English
-BETA DRAFT-
BETA
Safety information for RFID modules
WARNING
Multiple hazards. Do not disassemble the instrument for maintenance. If the internal components must
be cleaned or repaired, contact the manufacturer.
WARNING
Electromagnetic radiation hazard. Do not use the instrument in dangerous environments.
N O T I C E
This instrument is sensitive to electromagnetic and electromechanical interference. These interferences can have
an effect on the analysis performance of this instrument. Do not put this instrument near equipment that can
cause interference.
Obey the safety information that follows to operate the instrument in accordance with local, regional
and national requirements.
• Do not operate the instrument in hospitals and comparable establishments or near medical
equipment, such as pace makers or hearing aids.
• Do not operate the instrument near highly flammable substances, such as fuels, highly flammable
chemicals and explosives.
•Do not operate the instrument near combustible gases, vapors or dust.
• Keep the instrument away from strong vibration or shock.
• The instrument can cause interference in immediate proximity to televisions, radios and
computers.
• The warranty does not cover improper use or wear.
FCC conformance for RFID
This instrument may contain a registered radio frequency identification device (RFID). Refer to
Table 1 for the Federal Communications Commission (FCC) registration information.
Table 1 Registration information
Parameter Value
FCC identification number (FCC ID) YCB-ZBA987
IC 5879A-ZBA987
Frequency 13.56 MHz
Certification
Canadian Radio Interference-Causing Equipment Regulation, IECS-003, Class A:
Supporting test records reside with the manufacturer.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de classe A répond à toutes les exigences de la réglementation canadienne
sur les équipements provoquant des interférences.
FCC Part 15, Class "A" Limits
Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC
Rules. Operation is subject to the following conditions:
1. The equipment may not cause harmful interference.
2. The equipment must accept any interference received, including interference that may cause
undesired operation.
English 7
-BETA DRAFT-
BETA
Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment. This equipment has been tested
and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be required to
correct the interference at their expense. The following techniques can be used to reduce
interference problems:
1. Disconnect the equipment from its power source to verify that it is or is not the source of the
interference.
2. If the equipment is connected to the same outlet as the device experiencing interference, connect
the equipment to a different outlet.
3. Move the equipment away from the device receiving the interference.
4. Reposition the receiving antenna for the device receiving the interference.
5. Try combinations of the above.
Product overview
D A N G E R
Chemical or biological hazards. If this instrument is used to monitor a treatment process and/or
chemical feed system for which there are regulatory limits and monitoring requirements related to
public health, public safety, food or beverage manufacture or processing, it is the responsibility of the
user of this instrument to know and abide by any applicable regulation and to have sufficient and
appropriate mechanisms in place for compliance with applicable regulations in the event of malfunction
of the instrument.
D A N G E R
Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective
equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets
(MSDS/SDS) for safety protocols.
The TU5300 sc and the TU5400 sc sensors are used with an sc controller to measure low range
turbidity primarily in water purification water applications and in seawater with high salt
concentrations. Refer to Figure 1.
These sensors measure scattered light at an angle of 90° in a 360° radius around the axis of the
incident light beam.
The optional accessories for the sensors include: an integrated automatic system check, which
monitors for vial condensation and fouling, an automatic mechanical cleaning unit, a bubble trap or a
flow sensor.
Refer to Installation overview on page 10 to see an installation overview with all the accessories.
Refer to the documentation supplied with the accessories for more information.
8 English
-BETA DRAFT-
BETA
Figure 1 Product overview
1 User-specified button 8 Process head (shown) or cleaning head (optional)
2 Status indicator light 9 Process head water drain
3 RFID unit (optional) 10 Process head (open)
4 Knurled screws (3x) for (≤ 40 ºC (104 ºF) or high-
temperature screws (3x) for (40 to 70 ºC (104 to
158 ºF)) for the vial access cover1
11 Process head (closed)
5 Vial access cover 12 Cable channels
6 Inlet 13 Extension connector for more accessories
7 Outlet 14 Sensor cable
1Use a screwdriver to change the screws when the instrument is operated at 40 to 70 ºC (104 to 158 ºF).
Product components
Make sure that all components have been received. Refer to Figure 2. If any items are missing or
damaged, contact the manufacturer or a sales representative immediately.
English 9
-BETA DRAFT-
BETA
Figure 2 Product components
1 Turbidity sensor with 1.6 m cable (3 ft 3⅜ in.) 6 Screws, bracket to sensor (4x), 4 x 16 mm
2 Vial removal tool 7 Screws for tubing clips (4x), 2.2 x 6 mm
3 Maintenance rack18 Tubing clips (4x)
4 Vial wiper 9 Bracket for tubing attachments and optional
accessory
5 Desiccant cartridge 10 High-temperature screws (3x) for (40 to 70 ºC
(104 to 158 ºF))
1Not supplied with the TU5300 sc EPA model.
Installation
CAUTION
Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the
document.
Installation guidelines
N O T I C E
Make sure that a floor drain is available near the instrument. Examine the instrument daily for leaks.
This instrument is rated for an altitude of 3100 m (10,710 ft) maximum. Use of this instrument at an
altitude higher than 3100 m can slightly increase the potential for the insulation to breakdown, which
can result in an electric shock hazard. The manufacturer recommends that users with concerns
contact technical support.
• Install the sensor upright and level on a flat, vertical surface.
• Mounting hardware is supplied by the user.
•Refer to the documentation supplied with the accessories for installation of the optional units.
• Refer to Installation overview on page 10 for the minimum clearances.
Installation overview
Figure 3 shows the basic installation overview. The sensor can be used with optional accessories.
Refer to the documentation supplied with the accessory. Refer to the expanded manual on the
manufacturer's website for a full installation overview.
10 English
-BETA DRAFT-
BETA
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Instrumento de medición de HACH LANGE
HACH LANGE
HACH LANGE Filtrax Manual de usuario
HACH LANGE
HACH LANGE LZV902 Manual de usuario
HACH LANGE
HACH LANGE Pocket Colorimeter 2 Manual de usuario
HACH LANGE
HACH LANGE POCKET COLORIMETER II Series Guía del usuario
HACH LANGE
HACH LANGE LZX914.99.12400 Manual de usuario
HACH LANGE
HACH LANGE DR 3900 Manual de usuario
HACH LANGE
HACH LANGE ORBISPHERE 3654 Manual de usuario
HACH LANGE
HACH LANGE sensION+ EC7 Manual de usuario
HACH LANGE
HACH LANGE ORBISPHERE 6110 Manual de usuario
HACH LANGE
HACH LANGE QuikChem 8500 2 Series Instrucciones de funcionamiento
HACH LANGE
HACH LANGE POCKET COLORIMETER II Phosphate LCK 348 Guía del usuario
HACH LANGE
HACH LANGE sensION + pH3 Manual de usuario
HACH LANGE
HACH LANGE Pocket Colorimeter II Manual de usuario
HACH LANGE
HACH LANGE Pocket Colorimeter II Manual rápido
HACH LANGE
HACH LANGE Pocket Colorimeter II Guía del usuario
HACH LANGE
HACH LANGE LCK 303 Guía del usuario
HACH LANGE
HACH LANGE ORBISPHERE 3650 Manual de usuario
HACH LANGE
HACH LANGE DR 3900 Manual de usuario
HACH LANGE
HACH LANGE LINK2SC Manual de usuario
HACH LANGE
HACH LANGE FP 360 sc Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario