H3C SecPath T9000-S Manual de usuario
Manual version: APW101-20170630 BOM: 3123A1MQ
i
H3C SecPath T9000-S NSQM2IPSDSCA0 intrusion
prevention system service module
1 Identifier
The module identifier NSQM2IPSDSCA0 is at the upper right corner of the front panel.
2 Introduction
The H3C fourth-generation high performance intrusion prevention system service module
NSQM2IPSDSCA0 is developed for the H3C T9008-S intrusion prevention system. The module
provides features including firewall, VPN, content filtering, content identification, URL filtering, and
NAT and can greatly enhance security capabilities of the gateway.
3 Specifications
The module has a console port, a USB port, a GE copper port, and a hard disk slot
Figure 1 Front panel
(1) Captive screw (2) Ejector lever
(3) Hard disk slot (reserved) (4) Console port (CONSOLE)
(5) GE copper port (10/100/1000BASE-T) (6) USB port (reserved)
(7) Hard disk LED (HD) (8) System status LED (SYS)
Table 1 Module specifications
Item Specification
Flash 8MB Nor Flash
Memory Standard configuration: 16 GB (two 8GB VLP RDIMMs)
Micro SD card One built-in Micro SD card slot
Standard configuration: 8 GB
Dimensions (H × W × D) 40.1 × 399.2 × 376.8 mm (1.58 × 15.71 × 14.83 in)
Power consumption 116 W to 124 W
Weight 3.8 kg (8.38 lb)
Hot swapping Supported
1 2 3 4 5 6 78
Manual version: APW101-20170630 BOM: 3123A1MQ
ii
Item Specification
Ports
•1 × console port
•1 × USB port (reserved)
•1 × GE copper port
•1 × hard disk slot (reserved)
Ambient temperature
•Operating: 0°C to 45°C (32°F to 113°F)
•Not operating: –40°C to +70°C (–40°F to +158°F)
Rate of temperature change
•Operating: < 20°C (68°F)/h
•Not operating: < 30°C (86°F)/h
Ambient humidity
•Operating: 10 to 80% RH, noncondensing
•Not operating: 5 to 90% RH, noncondensing
Compatible device models and
slots T9008-S intrusion prevention system (slots 2 to 7)
Table 2 Console port specifications
Item Specification
Connector RJ-45
Interface standard RS-232
Transmission baud rate 9600 bps (default) to 115200 bps
Transmission medium Asynchronous serial cable
Transmission distance ≤15 m (49.21 ft)
Services
•Provides connection to an ASCII terminal.
•Provides connection to the serial port of a local or remote (through a
pair of modems) PC running terminal emulation program.
•Supports command line interface (CLI)
Table 3 10/100/1000BASE-T Ethernet copper port specifications
Item Specification
Connector RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Transmission medium Category-5 (or above) twisted pair cable
Transmission distance 100 m (328.08 ft)
Transmission rate and working
mode
•10 Mbps, half/full duplex
•100 Mbps, half/full duplex
•1000 Mbps, full duplex
Manual version: APW101-20170630 BOM: 3123A1MQ
iii
4 LEDs
The module provides LEDs to show the operating status of the module and the hard disk.
Table 4 LED description
LED Status Description
Hard disk (HD)
Fast flashing green The hard disk is reading and writing data.
Steady green The hard disk is operating correctly.
System status LED (SYS)
Off No power is being input or the module is faulty.
Slowly flashing green The system has started up and is operating
correctly.
Fast flashing green The system is loading software.
5 Installing and removing the module
CAUTION:
•Wear a reliably-grounded ESD wrist strap or ESD gloves when you install or remove the module.
•Do not touch the components on the PCB.
5.1 Installing the module
1. Face the front panel of the device. Remove the filler panel from the target slot.
This example uses slot 2 on the device.
2. Place the module horizontally on a workbench with the PCB facing up. Pull outward the ejector
levers on the module.
3. Gently push the module into the slot along the guide rails.
4. Push the ejector levers inward until the module is in close contact with the backplane.
5. Use a Phillips screwdriver to tighten the captive screws on the module.
Manual version: APW101-20170630 BOM: 3123A1MQ
iv
Figure 2 Installing the module
5.2 Removing the module
1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is
released.
2. Simultaneously pull the ejector levers at both sides of the module outward to separate the
module from the backplane, and pull the module slowly out of the chassis along the guide rails.
3. Place the module on an anti-static workbench with the PCB facing up, or put it in an anti-static
bag.
4. If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure
good ventilation in the device.
6 Software upgrade
For information about upgrading the module, see the release notes.
7 Obtaining documentation
To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk:
1. Go to http://www.h3c.com.hk/Technical_Documents.
2. Click Security Products, and then choose the desired product.
Copyright © 2017 New H3C Technologies Co., Ltd.
Este manual sirve para los siguientes modelos
1
Otros manuales de Cambiar de H3C
H3C
H3C WX3024E Manual de usuario
H3C
H3C S9500 Series Manual de usuario
H3C
H3C S6825-54HF Manual de usuario
H3C
H3C S6820 Series Manual de instalación
H3C
H3C s5820x series Manual de instalación
H3C
H3C S6850 Series Manual de usuario
H3C
H3C S5500-EI series Manual de usuario
H3C
H3C S7506 Manual de usuario
H3C
H3C S6800-54QT Manual de operación y mantenimiento
H3C
H3C S5560S Series Manual de instrucciones
H3C
H3C S9800 Series Manual de usuario
H3C
H3C H3C S3600 Series Manual de usuario
H3C
H3C S9500 Series Manual de usuario
H3C
H3C S5120-SI Series Manual de usuario
H3C
H3C S12500 Series Manual de usuario
H3C
H3C S10500 Series Manual de usuario
H3C
H3C S5830V2 series Manual de usuario
H3C
H3C S6520X-EI Series Manual de usuario
H3C
H3C S9500E Series Guía de inicio rápido
H3C
H3C S3100 Series Manual de usuario
