H3C S6520-EI Series Manual de usuario

Introduction to installation accessories 安装附件介绍

Before installation, wear an ESD-preventive wrist strap, and make sure the wrist strap makes good

skin contact and is correctly grounded.

在以下安装交换机的过程中，操作者需佩戴防静电腕带，确保防静电腕带与皮肤良好接触，并确认防

静电腕带已经良好接地。

The installation tools are not provided with the router. Prepare them yourself.

交换机不随机提供安装工具，请用户根据实际安装需求自己准备安装工具。

BOM:3101A0LC

Tool list 工具参考

H3C S6520-EI Switch Series Installation Quick Start-6PW102

H3C S6520-EI系列以太网交换机快速安装指南-6PW102

Phillips screwdriver

十字螺丝刀

ESD-preventive wrist strap

防静电腕带

Marker

记号笔

Groundingcable

地线Groundingscrew

接地螺钉

Mountingbracket

挂耳

M4countersunk-headscrew

M4沉头螺钉

Removable cabletie

可拆卸式扎带

Cage nut (user supplied)

浮动螺母（用户自备）

Fillerpanel

假面板

M6 screw

M6 螺钉（用户自备）

Long slide rail and chassis rail

短滑道和导轨

When you use mounting brackets, chassis rails, and slide rails to install the switch, determine the

installation positions for the accessories before installation.

利用滑道、滑道导轨配合挂耳将交换机安装到19英寸机柜时，可以根据需要调整附件在交换机上的安装

位置。

Mounting bracket installation position (two options) 挂耳安装位（二选一）

Chassis rail installation position (two options) 滑道导轨安装位（二选一）

Near the power modules

靠近电源侧 Near the network ports

靠近端口侧

Grounding cable installationposition (two options) 接地线安装位（二选一）

Primary grounding point

(near the power modules)

主接地点（靠近电源侧）

Auxiliary grounding point

(near the network ports)

备用接地点（靠近端口侧）

Near the power Modules

安装在靠近电源侧

Near the network ports

安装在靠近端口侧

The switch provides a grounding sign at the primary grounding point but not at the auxiliary grounding

point.

S6520-EI系列交换机主接地点标有接地标识，备用接地点上无接地标识。

The two grounding screws at the primary grounding point are also applicable to the auxiliary

grounding point.

S6520-EI系列交换机主接地点上的两个接地螺钉同样适用于备用接地点。

The switch provides three holes for installing mounting brackets near the network ports.

端口侧的挂耳安装孔只有三个。

Introduction to installation accessories 附件安装位置介绍

The installation positions of the accessories in the following figure are for illustration only. Select

installation positions for the accessories based on the installation requirement.

以下图中附件的安装位置仅供参考，请根据实际安装场景的需要选择合适的安装位置。

Airflow through the switch 交换机的风向设计

Installing the accessories to the switch 安装附件到交换机

Installing the switch in a 19-inch rack 安装交换机到19英寸机柜

Mount the switch in the rack.

安装交换机到机柜

Using the fan tray LSWM1FANSC

采用LSWM1FANSC风扇模块 Using the fan tray LSWM1FANSCB

采用LSWM1FANSCB 风扇模块

Installing and removing the FRUs 模块的安装与拆卸

Before installing the fan tray, make sure the airflow direction marked on the fan tray meets the

ventilation requirement of the installation site.

安装风扇模块前，请根据风扇模块的风向指示，确认气流方向和安装环境的通风要求一致。

The switch comes with the two fan tray slots empty. You must install two fan trays of the same

model on the switch. Do not power on the switch when no or only one fan tray is installed.

交换机出厂时两个风扇插槽均为空，为保证设备的正常散热，用户必须安装两个相同型号的风扇模

块，否则禁止交换机上电运行。

If both fan trays fail when the switch is operating, finish replacing the fan trays within 2 minutes.

交换机运行过程中，如果两个风扇模块均出现故障，则必须在2分钟内完成故障风扇模块的更换。

Connect the other end of the grounding cable to the grounding point on the rack.

接地线另一端连接到机柜接地点。

The switch provides front-to-back (port side to power module side) or back-to-front (power module

side to port side) airflow depending on the fan trays.

通过配置不同的风扇模块，可提供“端口侧到电源侧”和“电源侧到端口侧”两种通风走向，满足不

同环境下的散热要求。

Install the grounding cable before installing the switch to the rack.

为了防止机箱安装到机柜后无法安装接地线，因此请先将接地线安装到交换机的侧面接地点上。

Before installing cage nuts, mark their installation positions on the rack posts.

安装浮动螺母前，建议用户先使用记号笔在机柜立柱上标注浮动螺母安装位置。

Install cage nuts to the square

holes on the rack posts.

安装浮动螺母到机柜方孔条上

Install slide rails to the rack

posts.安装滑道到机柜

For more information about the product and installation procedures, log in to www.h3c.com.hk

如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com

To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk:

1. Go to http://www.h3c.com.hk/Technical_Documents.

2. Choose the desired product category and model.

您可以访问H3C网站（www.h3c.com）获取最新的产品配套资料：

1. 请访问网址：http://www.h3c.com/cn/Technical_Documents；

2. 选择产品类别和产品型号，即可查询和下载与该产品相关的手册。

Obtaining documentation 资料获取方式

If one fan tray fails when the switch is operating, replace the fan tray within 24 hours when the

ambient temperature is below 27°C (80.6°F). Do not remove the failed fan tray before replacement.

Replace the failed fan tray immediately when the ambient temperature is above 27°C (80.6°F).

交换机运行过程中，如果一个风扇模块出现故障，则当环境温度不高于27°C时，必须在24小时内完成

故障风扇模块的更换，且更换前必须保持故障风扇模块在位；当环境温度高于27°C时，请立即进行更

换。

Install and remove a power module 电源模块的安装与拆卸

Remove a power module 拆卸电源

Install a power module 安装电源

Remove a filler panel 拆卸假面板

Install and remove a filler panel 假面板的安装与拆卸

Install a filler panel 安装假面板

Install and remove a fan tray 风扇模块的安装与拆卸

Install a fan tray 安装风扇 Remove a fan tray 拆卸风扇

Install a filler panel to the empty power module slot to prevent dust from entering the chassis and

ensure good ventilation.

若电源模块插槽没有安装电源模块，请及时安装假面板，防止灰尘进入交换机，同时又保证设备的良

好通风散热。

Connect the DC power cord

连接直流电源线 Connect the AC power cord

连接交流电源线

Use a cable tie to secure the power cord to the handle of the power module 使用可拆

卸式扎带固定电源线，以防止电源线脱落

Connecting the power cord 连接电源线

Before connecting the power cord, connect the grounding cable and make sure the switch is correctly

grounded.

在连接电源线前，需先连接保护地线，保证交换机正确接地。

Connect the power cord to the switch first and then to the power source to avoid bodily injury.

连接电源线时，请先完成电源线与交换机侧的连接，再进行电源线与供电系统的连接，以免造成人身伤

害。

Otros manuales para S6520-EI Series

Otros manuales de Cambiar de H3C

H3C

H3C S6820-32H Manual de operación y mantenimiento

H3C

H3C s5820x series Manual de usuario

H3C

H3C SecPath T9000-S Manual de usuario

H3C

H3C A3600 Series Manual de usuario

H3C

H3C E500C-F Series Manual de usuario

H3C

H3C S9500 Series Manual de usuario

H3C

H3C S6890 Series Manual de instalación

H3C

H3C S5510 Series Manual de usuario

H3C

H3C s5820x series Manual de instalación

H3C

H3C S3100-52P Manual de usuario

H3C

H3C S5500-SI Series Manual de usuario

H3C

H3C S5500-EI series Manual de usuario

H3C

H3C S5120-SI Series Manual de usuario

H3C

H3C s5820x series Manual de instalación

H3C

H3C S5120-SI Series Manual de usuario

H3C

H3C S6890-30HF Manual de operación y mantenimiento

H3C

H3C S5500-HI Switch Series Manual de instalación

H3C

H3C H3C S3600 Series Manual de usuario

H3C

H3C S6805 Series Manual de usuario

H3C

H3C H3C S7500E Series Manual de operación y mantenimiento

H3C

H3C S12500-XS Series Manual de operación y mantenimiento

H3C

H3C S12500X-AF Series Manual de usuario

H3C

H3C S5560S-EI Series Manual de usuario

H3C

H3C S3100-52P Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario