H3C S5500-EI series Instrucciones de instalación
H3C S5500-EI Series Ethernet Switches
Command Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: 20071120-C-1.01
Product Version: Release 2102
Copyright © 2007, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care,
, TOP G, , IRF, NetPilot,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and
HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their
respective owners.
Notice
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.
To obtain the latest information, please access:
http://www. h3c.com
Technical Support
customer_service@h3c.com
http://www. h3c.com
About This Manual
Related Documentation
In addition to this manual, each H3C S5500-EI Series Ethernet Switches
documentation set includes the following:
Manual Description
H3C S5500-EI Series Ethernet
Switches Installation Manual It provides information for the system
installation.
H3C S5500-EI Series Ethernet
Switches Operation Manual It is used for assisting the users in data
configurations and typical applications.
Organization
H3C S5500-EI Series Ethernet Switches Command Manual is organized as follows:
Part Contents
1 Login Introduces the commands used for logging into the
Ethernet switch.
2 VLAN Introduces the commands used for configuring VLAN,
Voice VLAN, and GVRP.
3 IP Addressing and
Performance Introduces the commands used for configuring IP
address and IP performance.
4 QinQ-BPDU Tunneling Introduces the commands used for configuring QinQ
and BPDU Tunneling.
5 Port Correlation
Configuration Introduces the commands used for basic port
configuration and port isolation configuration.
6 Link Aggregation Introduces the commands used for link aggregation.
7 MAC Address Table
Management Introduces the commands used for configuring MAC
address forwarding table.
8 IP Source Guard Introduces the commands used for configuring MAC
address, IP address and port binding.
9 DLDP Introduces the commands used for DLDP and the
related configuration.
10 MSTP Introduces the commands used for configuring STP
and BRDU tunnel.
11 IP Routing-GR
Overview Introduces the commands used for displaying IP
routing tables.
Part Contents
12 IPv4 Routing Introduces the commands used for configuring IPv4
routing, static routing, RIP, OSPF, IS-IS, BGP, and
route policy.
13 IPv6 Routing Introduces the commands used for configuring IPv6
routing, static routing, RIPng, OSPFv3, IS-ISv6, and
BGP4+.
14 IPv6 Introduces the commands used for configuring IPv6
application, IPv6 tunneling, and so on.
15 Multicast Introduces the commands used for configuring IGMP
Snooping, MLD Snooping, multicast VLAN, multicast
policy, IGMP, PIM-DM, PIM-SM, and MSDP.
16 802.1x-HABP-MAC
Authentication
Introduces the commands used for 802.1x，HABP
and MAC address authentication related
configurations.
17 AAA RADIUS
HWTACACS Introduces the commands used for AAA, RADIUS,
HWTACACS, and the related configurations.
18 ARP Introduces the commands used for ARP and the
related configuration.
19 DHCP Introduces the commands used for DHCP and the
related configuration.
20 ACL Introduces the commands used for IPv4&IPv6-based
ACL and the related configuration.
21 QoS Introduces the commands used for QoS and the
related configuration.
22 Port Mirroring Introduces the commands used for port mirroring and
the related configuration.
23 Cluster Management Introduces the commands used for Cluster and the
related configuration.
24 UDP Helper Introduces the commands used for UDP Helper and
the related configuration.
25 SNMP-RMON Introduces the commands used for the configuration
to manage network devices through SNMP and
RMON.
26 NTP Introduces the commands used for NTP and the
related configuration.
27 DNS Introduces the commands used for DNS and the
related configuration.
28 File System
Management Introduces the commands used for file system
management.
29 Information Center Introduces the commands used for the configuration
to analyze and diagnose networks using the
information center.
Part Contents
30 System Maintaining
and Debugging Introduces the commands used for daily system
maintenance and debugging.
31 NQA Introduces the commands used for NQA and the
related configuration.
32 VRRP Introduces the commands used for VRRP and the
related configuration.
33 SSH Introduces the commands used for SSH and the
related configuration.
34 RRPP Introduces the commands used for RRPP and the
related configuration.
35 Port Security Introduces the commands used for Port Security and
the related configuration.
36 LLDP Introduces the commands used for LLDP and the
related configuration.
37 PoE Introduces the commands used for PoE.
38 sFlow Introduces the commands used for sFlow and the
related configuration.
39 SSL-HTTPS Introduces the commands used for SSL，HTTPS and
the related configuration.
40 PKI Introduces the commands used for PKI and the
related configuration.
41 Track Introduces the commands used for Track and the
related configuration.
42 Appendix Lists all the commands described in this command
manual in an alphabetic order. The parts and pages
where the commands are described are also given.
Conventions
The manual uses the following conventions:
I. Command conventions
Convention Description
Boldface The keywords of a command line are in Boldface.
italic Command arguments are in italic.
[ ] Items (keywords or arguments) in square brackets [ ] are
optional.
{ x | y | ... }
Alternative items are grouped in braces and separated by
vertical bars. One is selected.
Convention Description
[ x | y | ... ]
Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can be
selected.
[ x | y | ... ] *
Optional alternative items are grouped in square brackets
and separated by vertical bars. Many or none can be
selected.
&<1-n> The argument(s) before the ampersand (&) sign can be
entered 1 to n times.
# A line starting with the # sign is comments.
II. Symbols
Convention Description
Warning Means reader be extremely careful. Improper operation
may cause bodily injury.
Caution Means reader be careful. Improper operation may cause
data loss or damage to equipment.
Note Means a complementary description.
Otros manuales para S5500-EI series
22
Tabla de contenidos
Otros manuales de Cambiar de H3C
H3C
H3C S5560X-EI Series Manual de instalación
H3C
H3C S7500E-XS Series Manual de instalación
H3C
H3C S6800 Series Manual de usuario
H3C
H3C S5130S-EI series Manual de usuario
H3C
H3C S12500X-AF Series Manual de usuario
H3C
H3C H3C S5600 Series Manual de usuario
H3C
H3C T300M-XS Manual de operación y mantenimiento
H3C
H3C S9500 Series Manual de usuario
H3C
H3C S7500 Series Manual de usuario
H3C
H3C S5830V2 series Manual de usuario
H3C
H3C S9500 Series Manual de usuario
H3C
H3C S6520X-EI Series Manual de usuario
H3C
H3C S9820-8C Manual de usuario
H3C
H3C S6550XE-HI Series Manual de usuario
H3C
H3C SECPATH 5080F-CMW710-R9628P2414 Cómo utilizar
H3C
H3C WX3000 Series Manual de usuario
H3C
H3C S7500X Series Manual de usuario
H3C
H3C CR19000-16 Manual de operación y mantenimiento
H3C
H3C S12500X-AF Series Guía rápida
H3C
H3C S1850 Series Manual de usuario
