H3C S12500-X Manual de usuario

H3C S12500-X Switch Series

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Document version: 6PW111-20170512

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care, , IRF, NetPilot, Netflow,

SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage,

use, and disposal of this product must meet the applicable national laws and regulations.

Preface

The H3C S12500-X Switch Series Installation Guide guides you through the installation of your switch,

including preparing for installation, installing the switch, installing FRUs, setting up an IRF fabric,

connecting your switch to the network, troubleshooting, and replacement procedures.

This preface includes the following topics about the documentation:

•Audience.

•Conventions.

•Obtaining documentation.

•Technical support

•Documentation feedback.

Audience

This documentation is intended for:

•Network planners.

•Field technical support and servicing engineers.

•Network administrators working with the S12500-X switch series.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Descri

tion

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars, from

which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n> The argument or keyword and argument combination before the ampersand (&) sign can

be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Descri

tion

Boldface Window names, button names, field names, and menu items are in Boldface. For

example, the New User window opens; click OK.

> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.

Symbols

Convention Descri

tion

WARNING An alert that calls attention to important information that if not understood or followed can

result in personal injury.

CAUTION An alert that calls attention to important information that if not understood or followed can

result in data loss, data corruption, or damage to hardware or software.

IMPORTANT An alert that calls attention to essential information.

NOTE An alert that contains additional or supplementary information.

TIP An alert that provides helpful information.

Network topology icons

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports

Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access controller

engine on a unified wired-WLAN switch.

Represents an access point.

Wireless terminator unit.

Wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security gateway, or

load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL VPN,

IPS, or ACG module.

Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots, and

other information in the examples differ from what you have on your device.

Obtaining documentation

To access the most up-to-date H3C product documentation, go to the H3C website

at http://www.h3c.com.hk.

To obtain information about installation, configuration, and maintenance, click

http://www.h3c.com.hk/Technical_Documents

To obtain software version information such as release notes, click

http://www.h3c.com.hk/Software_Download

Technical support

servic[email protected]

http://www.h3c.com.hk

Documentation feedback

You can email your comments about product documentation to info@h3c.com.

We appreciate your comments.

Contents

Preparing for installation ············································································································································· 1

Safety recommendations ··················································································································································1

General safety recommendations···························································································································1

Electricity safety ························································································································································1

Handling safety ························································································································································1

ESD prevention ·························································································································································2

Laser safety································································································································································2

Examining the installation site ·········································································································································2

Weight support·························································································································································2

Temperature ······························································································································································2

Humidity ····································································································································································3

Cleanliness ································································································································································3

EMI·············································································································································································4

Grounding·································································································································································4

Power·········································································································································································4

Cooling······································································································································································5

Space·········································································································································································6

Installing the switch······················································································································································ 8

Confirming installation preparations·······························································································································8

Installing accessory kits ····················································································································································8

Accessory kits ···························································································································································8

Installing the power cord bracket (S12510-X AC and S12516-X AC switches)············································ 10

Attaching the plastic panel··································································································································· 11

Installing the switch in a rack········································································································································ 13

Switch dimensions and rack requirements ········································································································· 13

Installing slide rails················································································································································ 17

Installing cage nuts for attaching mounting brackets ························································································ 20

Mounting the switch in the rack··························································································································· 22

Grounding the switch ···················································································································································· 23

Grounding the switch with a grounding strip····································································································· 24

Grounding the switch through the PE wire of the AC power module······························································ 25

Grounding the switch through the RTN wire of the DC power module··························································· 25

Installing FRUs ····························································································································································27

Attaching an ESD wrist strap ········································································································································ 27

Installing cards ······························································································································································· 28

Installing an MPU/LPU·········································································································································· 29

Installing switching fabric modules······················································································································ 31

Installing power modules··············································································································································· 34

Installing a power module ···································································································································· 34

Connecting power cords ······································································································································ 35

(Optional) Installing a DC input terminal block·································································································· 37

Installing transceiver modules ······································································································································· 39

Installing an SFP+/SFP/QSFP+ module·············································································································· 39

Installing a CFP module ········································································································································ 40

Installing a CFP2 module······································································································································ 42

Installing a CXP module········································································································································ 43

Connecting a CXP fiber cable ····························································································································· 45

Connecting an SFP+/QSFP+/QSFP+ to SFP+ copper cable ··········································································· 46

Setting up an IRF fabric ·············································································································································47

IRF fabric setup flowchart·············································································································································· 47

Planning IRF fabric setup··············································································································································· 48

Planning IRF fabric size and the installation site································································································ 48

Identifying the master switch and planning IRF member IDs ············································································ 49

Planning IRF topology and connections ·············································································································· 49

Identifying physical IRF ports on the member switches ····················································································· 49

Installing IRF member switches ····································································································································· 49

Configuring basic IRF settings······································································································································· 50

Connecting the physical IRF ports ································································································································ 50

Verifying the IRF fabric configuration ·························································································································· 51

Connecting your switch to the network ····················································································································52

Accessing the switch for the first time ·························································································································· 52

Setting up the configuration environment ··········································································································· 52

Setting terminal parameters·································································································································· 53

Powering on the switch········································································································································· 56

Configuring the switch··················································································································································· 58

Configuring authentication on a user interface·································································································· 58

Configuring the basic access function ················································································································ 58

Configuration example ········································································································································· 58

Verifying the network configuration ···················································································································· 60

Connecting the switch to the network ·························································································································· 60

Connecting the switch to the network through an Ethernet twisted pair cable··············································· 60

Connecting the switch to the network through an optical fiber········································································ 60

Testing connectivity ························································································································································ 61

Troubleshooting··························································································································································62

Troubleshooting methods··············································································································································· 62

Configuration terminal problems·································································································································· 62

No terminal display ·············································································································································· 62

Garbled terminal display······································································································································ 63

Troubleshooting the switch during the operation······························································································· 63

Power supply system failure·········································································································································· 63

Fan failure······································································································································································· 64

MPU failure····································································································································································· 65

LPU and switching fabric module failure ····················································································································· 65

Interface failure······························································································································································· 66

Technical support ··························································································································································· 67

Replacement procedures ···········································································································································68

Replacing a power module··········································································································································· 68

Replacing a card···························································································································································· 69

Replacing an MPU or LPU ···································································································································· 70

Replacing a switching fabric module·················································································································· 72

Replacing a fan tray ······················································································································································ 74

Removing a fan tray·············································································································································· 75

Installing a fan tray ··············································································································································· 76

Replacing an air filter ···················································································································································· 77

Replacing a transceiver module ··································································································································· 81

Replacing an SFP+/SFP/QSFP+ module············································································································ 81

Replacing a CFP module ······································································································································ 81

Replacing a CFP2 module···································································································································· 81

Replacing a CXP module······································································································································ 82

Replacing a CXP fiber cable ································································································································ 82

Replacing an SFP+/QSFP+/QSFP+ to SFP+ copper cable·············································································· 83

iii

Appendix A Chassis views and technical specifications ························································································84

Chassis views ································································································································································· 84

Weights and dimensions··············································································································································· 87

Module power consumption and system power consumption ·················································································· 91

Card power consumption····································································································································· 91

Fan tray power consumption································································································································ 92

System power consumption·································································································································· 93

Heat dissipation ····························································································································································· 93

Environmental specifications········································································································································· 93

Noise··············································································································································································· 93

Appendix B FRUs and compatibility matrixes··········································································································95

MPUs ··············································································································································································· 95

Type A MPUs (for Release 10XX) ························································································································ 95

Type B MPUs (for Release 11XX)························································································································· 95

Type A and type B MPU specifications··············································································································· 96

LPUs ················································································································································································· 96

LPUs compatible with type A MPUs····················································································································· 96

LPUs compatible with type B MPUs ····················································································································· 98

Switching fabric modules ············································································································································101

Power modules ·····························································································································································101

DC input terminal blocks ·············································································································································102

Fan trays········································································································································································103

Air filters········································································································································································103

Transceiver modules ····················································································································································103

DC power cords···························································································································································108

AC power cords···························································································································································108

Appendix C LEDs ···················································································································································· 112

Chassis LEDs (S12510-X AC/S12510-X DC switch) ·······························································································112

Power module LED···············································································································································113

Fan tray status LED ··············································································································································114

MPU LED·······························································································································································114

Switching fabric module LED ·····························································································································114

LPU LED·································································································································································114

MPU LEDs······································································································································································114

LPU LEDs········································································································································································116

Switching fabric module LEDs·····································································································································119

Fan tray status LEDs ·····················································································································································119

Power module LEDs······················································································································································119

Appendix D Cables ················································································································································ 121

Console cable·······························································································································································121

Ethernet twisted pair cable··········································································································································121

RJ-45 connector ···················································································································································122

Cable pinouts·······················································································································································122

Cable type····························································································································································122

Pin assignments ···················································································································································124

Making an Ethernet twisted pair cable·············································································································124

Optical fiber ·································································································································································125

Optical fiber·························································································································································125

Optical fiber cable ··············································································································································125

Patch cord ····························································································································································126

Pigtail cord···························································································································································126

Fiber connector····················································································································································126

Precautions···························································································································································126

SFP+ copper cable·······················································································································································127

QSFP+ copper cable ···················································································································································127

QSFP+ to SFP+ copper cable ·····································································································································128

CXP fiber cable ····························································································································································128

Appendix E Engineering labels······························································································································ 130

Labels for cables···························································································································································130

Labels for network cables ···································································································································130

Labels for power cords ·······································································································································130

Generic labels······················································································································································131

Labels for devices·························································································································································132

Filling in labels ·····························································································································································132

Affixing labels·······························································································································································132

Affixing a label to a network cable···················································································································132

Affixing a label to a power cord·······················································································································133

Affixing a generic label······································································································································134

Affixing a label to a device································································································································135

Guidelines·····································································································································································135

Examples·······································································································································································135

Engineering labels for twisted-pair cables········································································································135

Engineering labels for optical fibers··················································································································137

Engineering labels for DC power cords ···········································································································139

Engineering labels for AC power cords ···········································································································140

Engineering labels for devices···························································································································141

Appendix F Cabling recommendations················································································································· 142

Routing network cables ···············································································································································142

Routing network cables for an S12510-X AC/S12510-X DC switch····························································142

Routing network cables for an S12516-X AC/S12516-X DC switch····························································144

Routing power cords····················································································································································145

General cabling requirements ····································································································································146

Prerequisites··································································································································································146

Cable management guidelines···································································································································147

Appendix G Repackaging the switch···················································································································· 150

Removing cables from the switch ·······························································································································150

Removing the power cords·································································································································150

Removing the console cable·······························································································································150

Removing the grounding cable··························································································································150

Removing the twisted pair and optical fiber ····································································································151

Repackaging the switch accessories··························································································································151

Repackaging the plastic panel and the air filter ······························································································151

Repackaging the power module························································································································152

Repackaging the card·········································································································································152

Repackaging the switch chassis ·································································································································152

Removing the chassis from the rack ··················································································································152

Removing the power cord bracket (S12510-X AC and S12516-X AC switches)········································153

Repackaging the switch chassis·························································································································154

Index ········································································································································································ 158

Preparing for installation

H3C S12500-X Switch Series includes the following models:

•S12510-X AC.

•S12510-X DC.

•S12516-X AC.

•S12516-X DC.

Safety recommendations

To avoid possible bodily injury and equipment damage, read Compliance and Safety Manual provided

with the switch and all safety recommendations in this chapter carefully before installation. The

recommendations do not cover every possible hazardous condition.

General safety recommendations

•Keep the chassis clean and dust-free.

•Do not place the switch on a moist area, and avoid liquid flowing into the switch.

•Make sure the ground is dry and flat and anti-slip measures are in place.

•Keep the chassis and installation tools away from walk areas.

•Do not wear loose clothing, jewelry (for example, necklace) or any other things that could get

caught in the chassis when you install and maintain the switch.

Electricity safety

•Clear the work area of possible electricity hazards, such as ungrounded power extension cables,

missing safety grounds, and wet floors.

•Locate the emergency power-off switch in the room before installation so you can quickly shut power

off when an electrical accident occurs.

•Remove all external cables, including power cords, before moving the chassis.

•Do not work alone when the switch has power.

•Always verify that power has been disconnected from a circuit.

Handling safety

CAUTION:

Do not hold the handle of a fan tray or a power distribution box, or the air vents of chassis to move the

switch. Any attempt to move the switch with these parts might cause equipment damage and even

bodily injury.

When you move an H3C S12500-X switch, follow these guidelines:

Otros manuales para S12500-X

Este manual sirve para los siguientes modelos

Otros manuales de Cambiar de H3C

H3C

H3C S3610 Series Manual de usuario

H3C

H3C 6W101 Manual de operación y mantenimiento

H3C

H3C S12500-X Manual de instalación

H3C

H3C XE 200 IP Manual de usuario

H3C

H3C S9820-64H Manual de usuario

H3C

H3C S7500 Series Manual de usuario

H3C

H3C S3610 Series Manual de usuario

H3C

H3C S5500-SI Series Manual de usuario

H3C

H3C S10500 Series Manual de usuario

H3C

H3C S6890 Series Guía rápida

H3C

H3C S5500-SI Series Manual de usuario

H3C

H3C S3610- 28P Manual de usuario

H3C

H3C S12500 Series Manual de servicio

H3C

H3C S6800 Series Manual de usuario

H3C

H3C S7502 Manual de usuario

H3C

H3C S9500 Series Manual de usuario

H3C

H3C LS-3100-16TP-EI-H3-A-O Manual de usuario

H3C

H3C H3C S3600 Series Instrucciones de instalación

H3C

H3C s5820x series Manual de usuario

H3C

H3C S9500 Series Manual de usuario

H3C

H3C S9500 Series Instrucciones de instalación

H3C

H3C S12500 Series Manual de usuario

H3C

H3C S5850 Series Manual de usuario

H3C

H3C S5500-EI series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario