H3C SR8800-X Manual de usuario

H3C SR8800-X Routers Installation Quick Start-6PW105

BOM: 3104A0FU

Tool list

Installation accessories

Safety recommendations

To avoid equipment damage or bodily injury, read the following safety recommendations before installation.

Note that the recommendations do not cover every possible hazardous condition.

This document provides a brief guide for installing H3C SR8800-X routers. For more installation

information, see H3C SR8800-X Routers Installation Guide.

The figures in this document are for illustration only.

The installation procedure is similar for the SR8800-X routers. The following uses an SR8808-X

router as an example unless otherwise specified.

Paper manuals cannot be updated in real time with product changes.For most recent product

information,see the E-manuals at the official website.

Prepare the following installation tools yourself as required.

This section only lists the most commonly used installation accessories.

To prevent ESD damage, always wear an ESD wrist strap when working with the router, cards, or PCBs.

Make sure the trap is reliably grounded.

Do not install the router, FRUs, or cables with the power on.

To avoid equipment damage or bodily injury, make sure the router is reliably grounded before powering on

the router.

To ensure good ventilation, install a filler panel in an unused slot.

Grounding cable ESD wrist strap M6 screw Removable cable tie Cage nut

Needle-nose

pliers Diagonal

pliers

Marker Wire-stripping

pliers

Claw hammer

Installing the router

Use a pattern tool to record the installation holes of the mounting brackets and mark the cage nut holes

in the rack posts accordingly.

Install cage nuts on the marked square holes.

Attaching cage nuts to the rack

Flat-blade

screwdriver Phillips

screwdriver

Installing the router in a rack Grounding the router

Connect the grounding cable to the grounding system in the equipment room. Do not connect it to a

fire main or lightning rod.

Installing FRUs

Before installing a card in the chassis, make sure the connectors on the card are not broken or blocked.

Installing cards

Do not hold the handle of the fan tray, power module, or the back panel of the chassis, or the air

vents of chassis to carry the chassis. Any attempt to carry the router with these parts might

cause equipment damage or even bodily injury.

After placing the router on the slide rails, Do not leave go of your hands immediately because this

might tip the router, damaging the router or even causing bodily injury.

To guarantee the grounding effect,

use the shipped yellow-green

grounding cable to ground the router.

Use a minimum of two people to move the

router. For heavy models, use a mechanical

lift as a best practice.

Connect the AC power cord to a vertical slot

Before installing an interface module, make sure the connectors on the module are not broken or blocked.

Connecting a power cord

Make sure the circuit breaker at the power input end is off when you connect the AC power cord to the

terminals on the power source.

Connecting an AC power cord

Installing interface modules

Installing power modules

Provide a circuit breaker for each power module and make sure the circuit breaker is off before

installation.

Do not install power modules of different models on the same router.

To avoid power module damage or bodily injury, move a power module by supporting its bottom

instead of holding its handle.

Connect the AC power cord to a horizontal slot

Press the power module handle inward until it is

secured in place before fastening screws.

Connecting the DC power cord for an LSUM1DC2400 or PSR2400-12D power module

Connecting the console cable

Powering on the router and verifying its operation

To access the router for the first time, use a console cable to connect the console port or USB console

port on the router. This example uses the console port.

Make sure the power cords are connected correctly and the power source is operating correctly. Then

power on the router. Verify that the router is operating correctly by observing the LEDs on the router. For

more information about the LEDs, see H3C SR8800-X Router Installation Guide.

Accessing the router

Connecting a DC power cord

Make sure each power cord has a separate circuit breaker.

Make sure the circuit breaker at the power input end is off before you connect the DC power cord.

The information in this document is subject to change without notice.

Connecting the DC power cord for a PSR2400-D power module

Otros manuales para SR8800-X

Otros manuales de Enrutador de red de H3C

H3C

H3C S9500 Series Manual de usuario

H3C

H3C S5500-SI Series Manual de usuario

H3C

H3C MSR 2600 Series Manual de usuario

H3C

H3C S5500-EI series Manual de usuario

H3C

H3C SR8800-F Manual de usuario

H3C

H3C SR6600 SPE-FWM Manual de instalación

H3C

H3C S3100 Series Instrucciones de instalación

H3C

H3C SR6600 SPE-FWM Manual de usuario

H3C

H3C S5500-SI Series Manual de usuario

H3C

H3C SR8800-F Manual de usuario

H3C

H3C MSR 2600 Series Manual de usuario

H3C

H3C CR16000-FA Series Manual de instrucciones

H3C

H3C SR6600-X Manual de usuario

H3C

H3C MSR810 Manual de usuario

H3C

H3C HIM-8FE Manual de usuario

H3C

H3C S1526 Manual de usuario

H3C

H3C CR16000-F Manual de usuario

H3C

H3C S3100-52P Instrucciones de instalación

H3C

H3C H3C S7500E Series Manual de instalación

H3C

H3C MSR 20 Series Manual de usuario

H3C

H3C SR8800-X Manual de operación y mantenimiento

H3C

H3C S5500-SI Series Manual de usuario

H3C

H3C MSR3600-28 Manual de usuario

H3C

H3C S12500R Series Manual de operación y mantenimiento

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad