H3C WX3500H series Manual de usuario

H3C WX3500H Series Access Controllers

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Document version: 6W103-20170519

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE,Aolynk, , H3Care, , IRF, NetPilot, Netflow, SecEngine,

SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies

Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage, use,

and disposal of this product must meet the applicable national laws and regulations.

Preface

This installation guide describes the procedures for installing, accessing, troubleshooting, and

maintaining the WX3500H access controllers.

This preface includes the following topics about the documentation:

•Audience.

•Conventions

•Obtaining documentation

•Technical support

•Documentation feedback

Audience

This documentation is intended for:

•Network planners.

•Field technical support and servicing engineers.

•Network administrators working with the WX3500H access controllers.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Description

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... } Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ] Square brackets enclose a set of optional syntax choices separated by vertical bars,

from which you select one or none.

{ x | y | ... } * Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] * Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n> The argument or keyword and argument combination before the ampersand (&) sign

can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface Window names, button names, field names, and menu items are in Boldface. For

example, the New User window opens; click OK.

Convention Description

> Multi-level menus are separated by angle brackets. For example, File > Create >

Folder.

Symbols

Convention Description

WARNING! An alert that calls attention to important information that if not understood or followed

can result in personal injury.

CAUTION: An alert that calls attention to important information that if not understood or followed

can result in data loss, data corruption, or damage to hardware or software.

IMPORTANT: An alert that calls attention to essential information.

NOTE: An alert that contains additional or supplementary information.

TIP: An alert that provides helpful information.

Network topology icons

Convention Description

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that

supports Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access

controller engine on a unified wired-WLAN switch.

Represents an access point.

Wireless terminator unit.

Wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security

gateway, or load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL

VPN, IPS, or ACG module.

Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots,

and other information in the examples differ from what you have on your device.

Obtaining documentation

To access the most up-to-date H3C product documentation, go to the H3C website at

http://www.h3c.com.hk

To obtain information about installation, configuration, and maintenance, click

http://www.h3c.com.hk/Technical_Documents

To obtain software version information such as release notes, click

http://www.h3c.com.hk/Software_Download

Technical support

service@h3c.com

http://www.h3c.com.hk

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

Contents

Preparing for installation ····································································1

Safety recommendations ·············································································································1

Safety symbols ···················································································································1

General safety recommendations ···························································································1

Electrical safety···················································································································1

Laser safety ·······················································································································2

Examining the installation site·······································································································2

Temperature and humidity·····································································································2

Cleanliness ························································································································2

Cooling ·····························································································································3

ESD prevention···················································································································3

EMI ··································································································································4

Lightning protection ·············································································································5

Installation accessories ···············································································································5

Installation tools·························································································································6

Pre-installation checklist ··············································································································6

Installing the device ··········································································8

Confirming installation preparations ·······························································································8

Installation flow··························································································································9

Mounting the device on a workbench ·····························································································9

Installing the device in a 19-inch rack ··························································································· 10

Mounting brackets ············································································································· 10

Mounting the device in a rack······························································································· 10

Grounding the device················································································································ 12

(Optional) Installing network port lightning protectors ······································································· 14

(Optional) Installing a surge protected power strip··········································································· 15

Connecting interface cables ······································································································· 15

Connecting the console cable and setting terminal parameters ··················································· 15

Connecting Ethernet cables································································································· 16

Installing a power module ·········································································································· 17

Connecting an AC power cord ···································································································· 18

Connecting a DC power cord······································································································ 18

Verifying the installation············································································································· 19

Powering on the device ············································································································· 19

Troubleshooting ·············································································22

Power module failure ················································································································ 22

Symptom ························································································································· 22

Solution··························································································································· 22

No display or garbled display on the configuration terminal ······························································· 22

Software loading failure ············································································································· 23

Symptom ························································································································· 23

Solution··························································································································· 23

Hardware management and maintenance ··········································· 24

Displaying hardware information for the device··············································································· 24

Displaying operational statistics for the device ········································································· 24

Displaying information about the device ················································································· 26

Displaying the electronic label data for the device····································································· 26

Displaying the CPU usage of the device ················································································· 26

Displaying the memory usage of the device ············································································ 27

Displaying the operational status of the built-in fans ·································································· 27

Displaying the operating state of power modules······································································ 28

Rebooting the device ················································································································ 28

Restrictions and guidelines·································································································· 28

Configuration procedure ····································································································· 29

Appendix A Chassis views and technical specifications ··························30

Chassis views ························································································································· 30

WX3508H ························································································································ 30

WX3510H ························································································································ 30

WX3520H ························································································································ 31

WX3540H ························································································································ 32

Power module views················································································································· 32

AC power module·············································································································· 32

DC power module·············································································································· 33

Interface numbering·················································································································· 33

WX3508H ························································································································ 33

WX3510H ························································································································ 33

WX3520H and WX3540H···································································································· 33

Technical specifications············································································································· 34

WX3508H ························································································································ 34

WX3510H ························································································································ 34

WX3520H ························································································································ 35

WX3540H ························································································································ 35

AC power module·············································································································· 36

DC power module·············································································································· 36

Transceiver module, fiber connector, and optical fiber views ····························································· 36

Transceiver module specifications ······························································································· 37

Appendix B LEDs ··········································································· 42

LEDs····································································································································· 42

LED description ······················································································································· 44

Index ···························································································46

Preparing for installation

H3C WX3500H access controllers include the following models:

•WX3508H.

•WX3510H.

•WX3520H.

•WX3540H.

Safety recommendations

To avoid any equipment damage or bodily injury, read the following safety recommendations before

installation. Note that the recommendations do not cover every possible hazardous condition.

Safety symbols

When reading this document, note the following symbols:

WARNING means an alert that calls attention to important information that if not understood or

followed can result in personal injury.

CAUTION means an alert that calls attention to important information that if not understood or

followed can result in data loss, data corruption, or damage to hardware or software.

General safety recommendations

•Make sure the installation site is flat, vibration-free, and away from electromagnetic

interferences. Make sure ESD and anti-slip measures are in place.

•Do not place the device on an unstable case or desk. The device might be severely damaged in

case of a fall.

•Keep the chassis and installation tools away from walk areas.

•Keep the chassis clean and dust-free.

•Do not place the device near water or in a damp environment. Prevent water or moisture from

entering the device chassis.

•Ensure good ventilation of the equipment room and keep the air inlet and outlet vents of the

device free of obstruction.

•Make sure the operating voltage is in the required range.

•Use a screwdriver to fasten screws.

•After you move the device from a location below 0°C (32°F) to the equipment room, follow these

guidelines to prevent condensation:

{Wait a minimum of 30 minutes before unpacking the device.

{Wait a minimum of 2 hours before powering on the device.

Electrical safety

•Carefully examine your work area for possible hazards, such as moist floors, ungrounded

power extension cables, or missing safety grounds.

•Locate the emergency power-off switch in the room before installation. Shut off the power

immediately if an accident occurs.

•Unplug all the external cables (including power cords) before moving the chassis.

•Do not work alone when you operate the device with the device powered on.

•Always verify that the power has been disconnected when you perform operations that require

the device to be powered off.

Laser safety

WARNING!

Do not stare into any open apertures of operating transceiver modules or optical fiber connectors.

The laser light emitted from these apertures might hurt your eyes.

CAUTION:

•Before you remove the optical fiber connector from a fiber port, execute the shutdown command

in interface view to shut down the port.

•Insert a dust cap into any open optical fiber connector and a dust plug into any open fiber port o

transceiver module port to protect them from contamination and ESD damage.

Examining the installation site

The device can only be used indoors. To ensure correct operation and a long lifespan for your device,

the installation site must meet the requirements in this section.

Temperature and humidity

Maintain the temperature and humidity in the equipment room at acceptable levels.

•Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical

property change of materials, and metal corrosion.

•Lasting low relative humidity can cause washer contraction and ESD and bring problems

including loose captive screws and circuit failure.

•High temperature can accelerate the aging of insulation materials and significantly lower the

reliability and lifespan of the switch.

To ensure correct operation of the device, the equipment room must meet the temperature and

humidity requirements listed in Table 1.

Table 1 Temperature/humidity requirements in the equipment room

Temperature Humidity

0°C to 45°C (32°F to 113°F) 5% RH to 95% RH, noncondensing

Cleanliness

Dust buildup on the chassis can result in electrostatic adsorption, which causes poor contact of metal

components and contact points, especially when indoor relative humidity is low. In the worst case,

electrostatic adsorption can cause communication failure. To ensure correct operation, the

equipment room must meet the dust concentration requirements listed in Table 2.

Table 2 Dust concentration limit in the equipment room

Substance Concentration limit (particles/m3)

Dust particles

≤3 x 104

(No visible dust on desk in three days)

NOTE:

Dust particle diameter ≥5 µm

To eliminate corrosion and premature aging of components, the equipment room must also meet

limits on salts, acids, and sulfides, as shown in Table 3.

Table 3 Harmful gas limits in an equipment room

Gas Max. (mg/m3)

SO20.2

H2S 0.006

NH30.05

Cl20.01

NO20.04

Cooling

The device uses left-to-right airflow. For adequate heat dissipation, make sure the following

requirements are met:

•A minimum clearance of 100 mm (3.94 in) is reserved around the air vents.

•The rack has a good ventilation system.

Figure 1 Airflow through the chassis (WX3508H)

ESD prevention

To prevent electrostatic discharge (ESD), follow these guidelines:

•Ground the device and rack or workbench reliably.

•Take dust-proof measures for the equipment room. For more information, see "Cleanliness."

Otros manuales para WX3500H series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de acceso IP de H3C

H3C

H3C WX3800H Series Manual de usuario

H3C

H3C WX Series Manual de usuario

H3C

H3C WBC580 G2 Manual de operación y mantenimiento

H3C

H3C WAC360 Series Manual de usuario

H3C

H3C WBC580 Manual de usuario

H3C

H3C WX Series Manual de usuario

H3C

H3C WX Series Manual de usuario

H3C

H3C WX2560H Manual de operación y mantenimiento

H3C

H3C WX6103 Manual de usuario

H3C

H3C WX Series Manual de usuario

H3C

H3C WX5004 Manual de usuario

H3C

H3C WX1800H series Manual de instalación

H3C

H3C WX5540E Manual de usuario

H3C

H3C WX2510H Manual de usuario

H3C

H3C WX Series Manual de instalación

H3C

H3C WX1804H Manual de usuario

H3C

H3C WX5540H Manual de usuario

H3C

H3C WX1800H series Manual de usuario

H3C

H3C WX2540H Manual de usuario

H3C

H3C WX5500H series Manual de usuario

H3C

H3C WX3820X Manual de usuario

H3C

H3C LSUM1WCME0 Manual de usuario

H3C

H3C LSWM1WCM10 Manual de usuario

H3C

H3C WX1800H series Manual de usuario

Manuales populares de Controladores de acceso IP de otras marcas

ZKTeco

ZKTeco SpeedFace-V5L Manual de usuario

Jantar

Jantar REX A-1-9 Manual de usuario

2N Access Unit Hoja de instrucciones

Kedacom

Kedacom KSCA120 Series Manual de usuario

G4S

G4S S870-EX Guía

PRASTEL

PRASTEL M2000PE Manual de usuario

Allegion

Allegion interflex IF-281 Cylinder Manual de usuario

TECOM

TECOM TS1067E Manual de usuario

Fermax

Fermax Memokey 100C Guía del usuario

Fermax

Fermax CITYLINE MEMOKEY Manual de instrucciones

Software House

Software House iSTAR Pro 2U RM Manual de instrucciones

AKCP

AKCP SP+ Manual de usuario

Bpt

Bpt HNA/102 Manual de usuario

Civintec

Civintec CV9601T-T-1F Manual de usuario

BioMax

BioMax N-X90W Manual de usuario

ZKTeco

ZKTeco OP-200 Manual de usuario

FingerTec

FingerTec s-Kadex Manual de usuario

C Prox Ltd

C Prox Ltd DPN-2 Manual de usuario