H3C LSUM1WCME0 Manual de usuario
Manual version: 6PW101-20170531 BOM: 3123A0UT
i
H3C S10500/S7500E LSUM1WCME0 card
1 Card identifier
The card identifier LSU1WCME0 is at the upper right corner of the front panel.
2 Introduction
The LSUM1WCME0 card is a high performance access controller module developed for
S10500/S7500E switches. The card provides functions including access control, wireless security,
wireless user authentication, RF analysis, content filtering, and NAT. You can install it on an H3C
S10500/7500E switch so that the switch can provide wired and wireless services without network
topology changes.
3 Specifications
The card has one console port and one 100/1000Base-T out-band management Ethernet port.
Figure 1 Front panel
(1) Captive screw
(2) Ejector lever
(3) 100/1000Base-T out-band management Ethernet port
(4) 100/1000Base-T out-band mana
g
ement Ethernet port LED (LINK/ACT)
(5) Console port (CONSOLE)
Table 1 Card specifications
Item S
p
ecification
CF card 4 GB
SDRAM
4 SDRAM slots
Standard configuration: 8 GB (four 2 GB DDR3 SDRAMs)
The card requires four DDR3 SDRAMs that have the same specifications.
Dimensions (H × W × D) 40.1 × 399.2 × 354.5 mm (1.58 × 15.72 × 13.96 in)
Power consumption 125 W to 180 W
Weight 4 kg (8.82 lb)
Hot swapping Supported
Ports
•1 console port
•One 100/1000BASE-T out-band management Ethernet port.
Manual version: 6PW101-20170531 BOM: 3123A0UT
ii
Item S
p
ecification
Ambient temperature
•Operating: 0°C to 45°C (32°F to 113°F)
•Not operating: –40°C to +70°C (–40°F to +158°F)
Ambient relative humidity
•Operating: 10% to 95%, noncondensing
•Non-operating: 5% to 95%, noncondensing
Compatible device models
•S7510E/S7506E-V/S7506E/S7506E-S/S7503E/S7503E-S/S7502E
•S10504/S10508/S10508-V/S10512
System software version See the release notes that come with the card.
Table 2 Console port specifications
Item S
p
ecification
Connector RJ-45
Interface standard RS-232
Transmission baud rate 9600 bps (default) to 115200 bps
Transmission medium Asynchronous serial cable
Transmission distance ≤15 m (49.21 ft)
Services
•Provides connection to an ASCII terminal.
•Provides connection to the serial port of a local PC running terminal
emulation program.
•Supports command line interface (CLI)
Table 3 100/1000BASE-T out-band management Ethernet port specifications
Item S
p
ecification
Connector RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Supported cable Category-5 (or above) twisted pair cable
Transmission distance 100 m (328.08 ft)
Operating mode
•100 Mbps, half/full duplex
•1000 Mbps, full duplex
4 LEDs
The card provides LEDs to show the operating status of the card and interfaces.
Table 4 LED description
LED Status
Descri
p
tion
100/1000BASE-T out-band management
Ethernet port LED (LINK/ACT)
Off No link is present on the port.
Steady green A link is present on the port.
Flashing green The port is sending or receiving data.
Manual version: 6PW101-20170531 BOM: 3123A0UT
iii
5 Installing and removing the card
CAUTION:
•Wear a well-grounded ESD wrist strap or ESD gloves before you install or remove the card.
•Do not touch the components on the PCB.
The slots on the H3C S10500/S7500E switches are either horizontally oriented or vertically oriented.
When installing the LSUM1WCME0 in a horizontal slot, make sure its PCB faces up. When installing the
LSUM1WCME0 in a vertical slot, make sure its PCB faces left.
This section uses a horizontally-oriented card to describe the installation and removal procedures.
5.1 Installing the card
1. Remove the blank filler panel from the slot for the card at the front of the switch.
This examples uses slot 6.
2. Place the card horizontally with the surface-mounted components facing up. Pull outward the
ejector levers and gently push the card in along the slot guide rails until the card is in close contact
with the backplane.
3. Push the ejector levers inward.
4. Tighten the captive screws with a Phillips screwdriver to secure the card in the slot.
Figure 2 Installing the card
1
2
Manual version: 6PW101-20170531 BOM: 3123A0UT
iv
5.2 Removing the card
1. Use a Phillips screwdriver to loosen the captive screws at both sides of the card until all pressure
is released.
2. Pull the ejector levers at both sides of the card outward, and pull the card along the guide rails until
it completely comes out of the backplane.
3. Place the card on an anti-static workbench with the surface-mounted components up, or put it in an
anti-static bag.
4. If no new card is to be installed, install a blank filler panel to prevent dust and ensure good
ventilation in the switch.
6 Logging in to the card
The card uses an independent operating system. Before you can configure the card, you must log in to
the card by using one of the following methods:
•Log in from the switch's CLI through the oap connect command.
•Log in through the card's Web interface, console port, Telnet, SSH, or SNMP.
H3C recommends that you log in to the card from the switch's CLI the first time you access the card. For
more information about other login methods, see the configuration guides that come with the card.
To log in to the card from the switch's CLI, perform the following task in user view:
Task Command Remarks
Log in to the card
through OAP.
•In standalone mode:
oap connect slot slot-number
•In IRF mode:
oap connect chassis chassis-number slot slot-number
To return to the CLI interface
of the switch, press Ctrl+K.
7 Software upgrade
The card uses independent BootWare and system software images. You must upgrade the card software
separately from the switch software. To ensure a successful card upgrade, H3C recommends that you
upgrade the card through the card's console port or management Ethernet port. For more information
about software upgrade of the card, see the release notes that come with the card.
8 Obtaining documentation
To access the most up-to-date H3C product documentation, go to
http://www.h3c.com.hk/Technical_Documents
For software upgrade, see the release notes for the device.
To access the release notes, go to
http://www.h3c.com.hk/Software_Download
Copyright © 2017 New H3C Technologies Co., Ltd.
Tabla de contenidos
Otros manuales de Controladores de acceso IP de H3C
H3C
H3C WX1800H series Manual de usuario
H3C
H3C WAC360 Series Manual de usuario
H3C
H3C WX2560H Manual de operación y mantenimiento
H3C
H3C LSWM1WCM10 Manual de usuario
H3C
H3C WX1804H-PWR Manual de usuario
H3C
H3C WX5500H series Manual de usuario
H3C
H3C WX2540E Manual de usuario
H3C
H3C WX5004 Manual de usuario
H3C
H3C WX2880X Manual de usuario
H3C
H3C WX6103 Manual de usuario
H3C
H3C WX5540H Manual de operación y mantenimiento
H3C
H3C WX Series Manual de usuario
H3C
H3C WX5002 Manual de instrucciones
H3C
H3C WX3800H Series Manual de usuario
H3C
H3C WX5002ACCESSCONTROLLER Manual de usuario
H3C
H3C WX2540H Manual de usuario
H3C
H3C LS8M1WCMA0-OVS Manual de usuario
H3C
H3C WX3500H series Manual de usuario
H3C
H3C WBC580 G2 Manual de operación y mantenimiento
H3C
H3C vAC1000 Manual de usuario
