Häfele PP8100 Manual de usuario
www.hafele.com
Model PP8100
Digital door lock
* The contents of this user manual are subject to change without prior notice
to the user in order to enhance performance of the products.
PP8100
Installation guide
Contents
Product specification…………………………………………………………………………………...2
Components………….…………………………………………………………………………………3
Prepare for installation………….………………………………………………………………………4
Installation…………………………….…………………………………………………………………6
1
Product specifications
Inside panelOutside panel
Mortise lock
Key cylinder Emergency
power port
Reboot button
Deadbolt
Shaft socket
Sensor latch
Latch bolt
Touch keypad
CLOSE/OPEN
button
Safe handle
switch
Battery cover
Push pull handle
Push pull handle
Card reader area
Fingerprint sensor
2
Key cylinder Emergency power port
Reboot button
Components
1
9 10 11 12 13
2 3 4 5 6 7 8
1. Outside panel assembly (1 pc)
2. Pressure spring (2 pcs)
3. Connecting screw bolt (1 pc)
4. Mounting plate (1 pc)
5. Square shaft (2 pcs)
6. Inside panel assembly (1 pc)
13. Rubber plug (1 pc)
14. Strike assembly
- Left strike plate (1 pc)
- Right strike plate (1 pc)
- Strike box (1 pc)
15. Mechanical key (2 pcs)
3
7. Mounting screw (1 pc)
8. Battery cover (1 pc)
9. Connecting screw bolt (4 pcs)
10. Mortise lock (1 pc)
11. Mounting plate screw (4pcs)
12. Mounting screw (1 pc)
14
15
Preparing for installation
4
Check door open direction
This product fits for all door open directions-Left-in/Left-out/Right-in/Right-out
Indoor
Outdoor
Outdoor
Outdoor
Outdoor
Indoor
Indoor
Indoor
Preparing for installation
Please change the screw position according to door open direction.
Change open direction (Inside panel assembly)
Check door thickness
1. Please choose correct screw pack according to your door thickness.
2. Default screw pack is for door thickness 38-60mm.
Arrow
direction
Arrow
direction
Arrow
direction
Arrow
direction
Right-in Left-in
Left-out
Screw Screw
Right-out Screw Screw
Screw
Screw
Screw
Screw
5
Installation
Indoor
screw bolt
screw bolt
square shaft
Indoor
Outdoor
4. Pass the connection wire through the top bore.
Then align and insert square shaft into mortise
holes to make the front panel fit against the door
closely.
Do not make the
mortise deadbolt
come out
1. Spring: the big end is downward.
2. Select the square shafts and screw bolts with proper
length according to door thickness range.
1. Mark and drill bores by using the installation
template first, then fix the mortise into the door
frame.
3. Fix 5 screw bolts on the front panel, place square
shaft and pressure spring into the bore.
2. Tighten the 2 screws to fix the mortise in the
door.
6
Installation
Indoor
Square
shaft
6. Place square shaft in the back panel in proper
order.
Outside
panel
socket
Mortise
socket
5. Install the mounting plate with fixing screw tightly
against the door surface.
7. Install the connecting wires of front panel into the
related sockets of the back panel. Then align and
insert the square shaft into mortise hole, make the
back panel fit against the door closely.
8. Tighten the 2 fixing screws.
Indoor
Indoor
Indoor
7
Installation
After installing the strike assembly,
please check if the lock works smoothly
by opening/closing door. Test if mechanical key works smoothly
after installation.
Indoor
Battery cover
Screw hole cover
9. Install the batteries and battery cover. Cover the screw
hole with rubber plug, then install then strike assembly
to finish installation.
10. Please check push-pull handle, safe handle
switch and mechanical key for proper operation.
8
Tabla de contenidos
Otros manuales de Cerradura de puerta de Häfele
Häfele
Häfele EL10K Guía de solución de problemas
Häfele
Häfele DL7600 Manual de usuario
Häfele
Häfele EFL 30 Manual de usuario
Häfele
Häfele DL6600 Manual de usuario
Häfele
Häfele 911.52.122 Manual de usuario
Häfele
Häfele 911.52.122 Manual de usuario
Häfele
Häfele 7100 Manual de usuario
Häfele
Häfele EL6500-TCS Manual de usuario
Häfele
Häfele 231.07.070 Manual de usuario
Häfele
Häfele ER5000 Manual de usuario
