GW Instek MPO-2000 Series MPO-2000B Manual de usuario

Multi-Function Programmable

Oscilloscope

MPO-2000 Series

USER MANUAL

ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan

TABLE OF CONTENTS

Table of Contents

SAFETY INSTRUCTIONS .................................................. 4

GETTING STARTED.......................................................... 9

MPO-2000 Series Overview........................................ 10

Appearance................................................................ 14

Set Up ....................................................................... 26

MEASUREMENT ............................................................ 34

Basic Measurement ................................................... 35

Automatic Measurement............................................ 42

Cursor Measurement ................................................. 57

Math Operation ......................................................... 63

ADVANCED CONFIGURATION ....................................... 73

Acquisition ................................................................ 76

Segmented Memory Acquisition ................................ 81

Display ...................................................................... 91

Python script execution.............................................. 97

Python APP Operation ..............................................102

Menu Description .....................................................103

Built-in Python apps .................................................118

Horizontal View ........................................................119

Vertical View (Channel).............................................126

Bus Key Configuration ..............................................135

Trigger ......................................................................156

Search.......................................................................187

System Settings and Miscellaneous Settings ............195

ARBITRARY WAVE GENERATOR ....................................201

Arbitrary Wave Generator Operation .........................202

MPO-2000 series User Manual

SPECTRUM ANALYZER ................................................. 233

Spectrum Analyzer operation ................................... 234

DMM............................................................................ 252

DMM function ......................................................... 253

POWER SUPPLY ............................................................ 261

Power supply function ............................................. 262

APPLICATIONS ............................................................. 265

Introduction............................................................. 267

Go-NoGo application ............................................... 270

DVM application ...................................................... 275

Data Log application................................................ 277

Digital Filter application .......................................... 279

Mask application ..................................................... 281

FRA application ....................................................... 291

CAN FD Serial Bus Interface .................................... 304

USB Packet .............................................................. 308

Flexray ..................................................................... 312

USB PD .................................................................... 316

I2S ........................................................................... 321

SAVE/RECALL ............................................................... 325

File Format/Utility ................................................... 326

Create/Edit Labels.................................................... 332

Save ......................................................................... 335

Recall ....................................................................... 342

Reference Waveforms............................................... 347

FILE UTILITIES ............................................................. 349

HARDCOPY KEY ........................................................... 357

REMOTE CONTROL CONFIG ........................................ 359

TABLE OF CONTENTS

Interface Configuration .............................................360

Web Server................................................................364

MAINTENANCE ............................................................368

FAQ .............................................................................. 372

APPENDIX ....................................................................374

Updating the Firmware .............................................375

MPO-2000B/P Series Specifications..........................377

Probe Specifications .................................................385

Dimensions ..............................................................386

Certificate Of Compliance .........................................387

INDEX ..........................................................................387

MPO-2000 series User Manual

SAFETY INSTRUCTIONS

This chapter contains important safety instructions

that you must follow during operation and

storage. Read the following before any operation

to insure your safety and to keep the instrument in

the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the Product

name.

WARNING Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION Caution: Identifies conditions or practices that

could result in damage to the equipment or to

other properties.

DANGER High Voltage

Note Attention required

Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

SAFETY INSTRUCTIONS

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

Safety Guidelines

General

Guideline

WARNING

CAUTION

Make sure the BNC input voltage does not

exceed 300Vrms.

Never connect a hazardous live voltage to the

ground side of the BNC connectors. It might

lead to fire and electric shock.

Do not place any heavy object on the MPO-2000

series.

Avoid severe impact or rough handling that

leads to damaging the MPO-2000 series.

Do not discharge static electricity to the MPO-

2000 series.

Use only mating connectors, not bare wires, for

the terminals.

Do not block the cooling fan opening.

Do not perform measurement at a power source

or building installation (Note below).

Do not disassemble the MPO-2000 series unless

you are qualified.

Note (Measurement categories) EN 61010-1 specifies the measurement

categories and their requirements as follows. The MPO-2000 series

falls under category I.

Measurement category IV is for measurements performed at

the source of low-voltage installation.

Measurement category III is for measurements performed in

the building installation.

Measurement category II is for measurements performed on

circuits directly connected to the low voltage installation.

Measurement category I is for measurement performed on

circuits not directly connected to Mains.

MPO-2000 series User Manual

Power Supply

WARNING

AC Input voltage: 100 - 240V AC, 50 - 60Hz,

auto selection. Power consumption: 50W for

MPO-2000 series.

Connect the protective grounding conductor of

the AC power cord to an earth ground, to avoid

electrical shock.

Cleaning the

MPO-2000 Series

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals containing harsh

materials such as benzene, toluene, xylene and

acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Relative Humidity: ≤80%, 40°C or below; ≤45%,

41°C ~ 50°C

Altitude: < 2000m

Temperature: 0°C to 50°C

Note (Pollution Degree) EN 61010-1: specifies the pollution degrees and

their requirements as follows. The MPO-2000 series falls under

degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

SAFETY INSTRUCTIONS

Storage

environment

Location: Indoor

Temperature: -10°C to 60°C

Humidity: Up to 93% RH (non-condensing) /

≤40ºC, up to 65% RH (non-condensing) / 41ºC

~ 60 ºC

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

MPO-2000 series User Manual

Power cord for the United Kingdom

When using the oscilloscope in the United Kingdom, make sure the

power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow: Earth

Blue: Neutral

Brown: Live (Phase)

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed as

follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the

terminal marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or

contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable

of 0.75mm2should be protected by a 3A or 5A fuse. Larger

conductors would normally require 13A types, depending on the

connection method used.

Any exposed wiring from a cable, plug or connection that is engaged

in a live socket is extremely hazardous. If a cable or plug is deemed

hazardous, turn off the mains power and remove the cable, any

fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de prueba de GW Instek

GW Instek

GW Instek GDS-3152 Manual de usuario

GW Instek

GW Instek PEL-2000 Series Manual de usuario

GW Instek

GW Instek GPT-700A Series Manual de usuario

GW Instek

GW Instek AEL-5000 Series Manual de usuario

GW Instek

GW Instek GDS-3000 Series Manual de usuario

GW Instek

GW Instek GDS-3352A Manual de usuario

GW Instek

GW Instek GOS-620FG Manual de usuario

GW Instek

GW Instek GRS-6052A Manual de usuario

GW Instek

GW Instek GDS-3152 Manual de usuario

GW Instek

GW Instek GDS-1000A-U Series Manual de usuario

GW Instek

GW Instek PEL-2002 Manual de usuario

GW Instek

GW Instek LCR-16 Manual de usuario

GW Instek

GW Instek MDO-2000A Series Manual de usuario

GW Instek

GW Instek GDS-3000 Series Manual de usuario

GW Instek

GW Instek GPT-9000 series Manual de usuario

GW Instek

GW Instek GDS-800 Series Manual de usuario

GW Instek

GW Instek GPT-9000 series Manual de usuario

GW Instek

GW Instek PEL-2000A Series Manual de usuario

GW Instek

GW Instek GDS-1000B Series Manual del propietario

GW Instek

GW Instek GDS-2000A Series Manual de usuario

GW Instek

GW Instek GPT-9000 series Manual de usuario

GW Instek

GW Instek GPT-9500 Series Manual de usuario

GW Instek

GW Instek MSO-2000EA Manual de usuario

GW Instek

GW Instek GDS-3000 Series Manual del propietario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario