GW Instek PEL-2000A Series Manual de usuario

Programmable DC Electronic

Load

PEL-2000A Series

USER MANUAL

ISO-9001 CERTIFIED MANUFACTURER

March 2018

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of the GW instek company.

The information in this manual was correct at the time of printing.

However, GW instek continues to improve products and reserves the

right to change specification, equipment, and maintenance procedures

at any time without notice.

Table of Contents

SAFETY INSTRUCTIONS ...................................................6

GETTING STARTED.........................................................11

Main Features........................................................13

Series Overview .....................................................15

Package Contents and Accessories ........................17

Measurement Overview .........................................19

Front Panel Overview.............................................20

Display Overview –Mainframe ..............................25

Rear Panel Overview ..............................................29

Front Panel Overview –Load Module ....................32

LED Display Overview –Load Module ...................35

Installation ............................................................38

Load Connections ..................................................45

Frame Link Connection ..........................................55

Channel Control Connection ..................................57

Go/NoGo Connection ............................................60

OPERATING DESCRIPTION ............................................. 61

Operating Mode Description .................................62

Group Unit Mode ..................................................72

Run Program .........................................................74

Sequence ...............................................................77

OCP Test Automation ............................................82

Parallel Dynamic Loading ......................................83

Configurations Description ....................................84

Interface and System .............................................94

TUTORIALS .................................................................. 101

Local loads ..........................................................102

Single Channel Load ............................................104

PEL-2000A Series User Manual

Parallel Load Modules .........................................106

Programming.......................................................108

Sequences ...........................................................110

Frame Link...........................................................111

Channel Control...................................................113

General Configuration Options ............................115

OPERATION ................................................................. 117

Local Mode Operation .........................................120

Mainframe Basic Operation .................................126

Creating a Program Sequence ..............................150

Edit Sequence ......................................................163

OCP Test Automation ..........................................173

Channel Configuration .........................................180

Mainframe Configuration .....................................208

Interface Configuration (settings) ........................232

RS232 and USB CDC Function Check ...................238

GPIB Function Check ...........................................242

Saving/Recalling Channels...................................244

INTERFACE................................................................... 280

Interface Configuration ........................................281

FAQ.............................................................................. 291

APPENDIX .................................................................... 292

Fuse Replacement ................................................292

Firmware Update .................................................293

Calibration ...........................................................296

Range Chart .........................................................297

Default Settings ...................................................302

Specifications ......................................................305

Dimensions .........................................................315

EC Declaration of Conformity ..............................318

Table of Contents

INDEX .......................................................................... 319

PEL-2000A Series User Manual

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow when operating

the PEL-2000A series, and when keeping it in

storage. Read the following before operating the

PEL-2000A series to ensure your safety and to

keep the PEL-2000A series in the best possible

condition.

Safety Symbols

These safety symbols may appear in this manual or on the PEL-

2000A series.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the PEL-2000A series or

to other properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

SAFETY INSTRUCTIONS

Safety Guidelines

General

Guideline

CAUTION

Do not place any heavy object on the PEL-2000A

series.

Avoid severe impact or rough handling that

leads to damaging the PEL-2000A series.

Do not discharge static electricity to the PEL-

2000A series.

Do not block or obstruct the cooling fan vent

openings.

Do not perform measurement at circuits directly

connected to Mains (Note below).

Do not disassemble the PEL-2000A series unless

you are qualified as service personnel.

The equipment is not for measurements

performed for CAT II, III and IV.

(Measurement categories) EN 61010-1:2010 specifies the

measurement categories and their requirements as follows. The

PEL-2000A series falls under category I.

Measurement category IV is for measurement performed at the

source of low-voltage installation.

Measurement category III is for measurement performed in the

building installation.

Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

Measurement category I is for measurements performed on

circuits not directly connected to Mains.

Power Supply

WARNING

AC Input voltage range: 100-120Vac/ 200-

240Vac (90-132Vac/ 180-250Vac)

Frequency: 47~63Hz

Power rating: PEL-2004A: 250VA Max

PEL-2002A: 150VA Max

Connect the protective grounding conductor of

the AC power cord to an earth ground, to avoid

electrical shock.

PEL-2000A Series User Manual

Fuse

WARNING

Fuse type: T3.15A/250V

Make sure the correct type of fuse is installed

before power up.

To avoid fire, only replace the fuse with the

specified type and rating.

Disconnect the power cord before fuse

replacement.

Make sure the cause of a fuse blowout is fixed

before replacing the fuse.

Cleaning the

PEL-2000A

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals or cleaners containing

harsh material such as benzene, toluene, xylene,

and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Temperature: 0°C to 40°C

Altitude: Up to 2000m

Transient Overvoltage on the main supply is

2500V.

SAFETY INSTRUCTIONS

(Pollution Degree) EN 61010-1:2010 specifies the pollution degrees

and their requirements as follows. The PEL-2000A series falls under

degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

Storage

environment

Location: Indoor

Relative Humidity: < 80%

Temperature: −10°C to 70°C

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

PEL-2000A Series User Manual

Power cord for the United Kingdom

When using the PEL-2000A series in the United Kingdom, make

sure the power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with

the following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with the

coloured marking identified in your plug/appliance, proceed as

follows:

The wire which is coloured Green & Yellow must be connected to the

Earth terminal marked with either the letter E, the earth symbol or

coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal

marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or

contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable of

0.75mm2 should be protected by a 3A or 5A fuse. Larger conductors

would normally require 13A types, depending on the connection

method used.

Any exposed wiring from a cable, plug or connection that is engaged

in a live socket is extremely hazardous. If a cable or plug is deemed

hazardous, turn off the mains power and remove the cable, any fuses

and fuse assemblies. All hazardous wiring must be immediately

destroyed and replaced in accordance to the above standard.

Otros manuales para PEL-2000A Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de prueba de GW Instek

GW Instek

GW Instek GDS-1000A Series Manual del propietario

GW Instek

GW Instek GDS-3000 Series Manual de usuario

GW Instek

GW Instek GOS-6200 Manual de usuario

GW Instek

GW Instek GDS-2000A Series Manual de usuario

GW Instek

GW Instek GDS-2000A Series Manual de usuario

GW Instek

GW Instek GCT-9040 Manual de usuario

GW Instek

GW Instek C-1200 Manual de usuario

GW Instek

GW Instek GPT-9801 Manual de usuario

GW Instek

GW Instek GPT-9000 series Manual de usuario

GW Instek

GW Instek GDS-3000 Series Manual de usuario

GW Instek

GW Instek LCR-05A Manual de usuario

GW Instek

GW Instek GDS-1000B Series Manual del propietario

GW Instek

GW Instek GPT-9000 series Manual de usuario

GW Instek

GW Instek GPT-9000 series Manual de usuario

GW Instek

GW Instek PEL-3000E Manual de usuario

GW Instek

GW Instek LCR-16 Manual de usuario

GW Instek

GW Instek MDO-2000A Series Manual de usuario

GW Instek

GW Instek GRF-1300 Manual de usuario

GW Instek

GW Instek GPT-9000 series Manual de usuario

GW Instek

GW Instek PEL-3000 Series Manual de usuario

GW Instek

GW Instek GDS-1000-U Series Manual de usuario

GW Instek

GW Instek GDS-1000A-U Series Manual de usuario

GW Instek

GW Instek GPT-9000 series Manual de usuario

GW Instek

GW Instek GDS-3000 Series Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario