GVD M6000 Series Manual de usuario
Hardware Quick Installation Guide i
Revision History
Revision Time Description
Feb 2016 The M6000 Series changes the motherboard, which involves the following changes
of the product:
M6000 Series no longer supports FBWF but VHD. The following conguration
can be conducted straight without FBWF concern:
■Congure Network as described on page 9.
■Congure Screen Resolution as described on page 10.
■Congure Date, Time & Time Zone as described on page 11.
By VHD support, system backup and recovery becomes available for M6000
Series:
■Back up Initial System State as described on page 17.
■Back up System State as described on page 18.
■Recover System State as described on page 20.
The M6000 Series has the rear I/O ports changed, which involves the following
update in this document.
■Install Hardware: M6000 Series on page 7 is updated.
May 2016 A brand new NVR M2002 is launched, which involves the following changes of this
document:
Section Install Hardware: M2002 is newly added on page 3.
Section Appendix. Install HDDs: M2002 is newly added on page 33.
Hardware Quick Installation Guide
ii
Contents
Revision History.......................................................................i
Contents .................................................................................ii
Hardware Requirements........................................................ 1
Install Hardware..................................................................... 2
M95 ....................................................................................... 2
M2002 ................................................................................... 3
M3000 Series ........................................................................ 4
M4006 & M4006-AR.............................................................. 5
M4006-IR, M4008 & M4008-AR ............................................ 6
M6000 Series ........................................................................ 7
Set up Windows..................................................................... 8
Congure Network................................................................. 9
Congure Screen Resolution............................................... 10
Congure Date, Time & Time Zone ......................................11
Enable Watchdog Timer ...................................................... 12
Initialize HDD....................................................................... 13
Create Storage Volue .......................................................... 14
Auto-add a Camera ............................................................. 15
Back up Initial System State................................................ 17
Back up System State ......................................................... 18
Recover System State......................................................... 20
Troubleshooting................................................................... 22
Appendix. Create RAID5 on M3004-IR & M4006-IR ........... 24
Appendix. Create RAID5 on M4006-AR, M4008-AR & M6000
Series .................................................................................. 25
Appendix. Install HDDs........................................................ 30
M95 ..................................................................................... 30
M2002 ................................................................................. 33
M3000 Series ...................................................................... 36
M4000 Series ...................................................................... 39
M6000 Series ...................................................................... 42
Appendix. Connect S6000 Series to M6000Series ............. 44
Hardware Quick Installation Guide 1
Hardware Requirements
Recording data is one of the most important parts for video surveillance, and hard disk drives
are one of the most important components to safely store the recording data.
It is always recommended that you use the hard disk drives certified by GVD. Find the list of
the GVD-certified hard disk drives at the link below:
http://www.gvdigital.com/gvdweb/html/document/Support_Lists/Certified%20HDD%20List.pdf
NOTE:
* GVD does not guarantee the system performance if a HDD model that is not certified by GVD is used.
* GVD always recommends the use of Enterprise Class SATA hard drives for GVD Enterprise NVR, Failover Server,
Backup Server, Extended Storage because it supports TLER (Time Limited Error Recovery), higher MTBF, higher
Duty Cycles and typically include a sensor for rotation and vibration.
Hardware Quick Installation Guide
2
Install Hardware: M95
➊ Connect the keyboard to one of the USB ports.
➋ Connect the mouse to one of the USB ports.
➌ Connect the display monitor to the DisplayPort or HDMI port.
➍ Connect the power cord to the AC power socket at the rear panel of the unit.
➎ Plug in a CAT-6 UTP cable to the RJ-45 Gigabit LAN port, and connect the other end of
the cable to a switch connecting to the camera network.
➏ Plug in the speaker to the audio output port if necessary.
➐ The unit then auto powers on when the power cord is connected to power source.
* GVD isn’t responsible for any system malfunction if a 3rd-party application that isn’t certified by GVD is installed in the
system.
* M95 series support decoding the resolution from D1 up to 20M.
* DO NOT plug any USB device except keyboard & mouse before the operating system starts.
7
124
3
6
5
Hardware Quick Installation Guide 3
Install Hardware: M2002
➊ Connect the keyboard and mouse to the USB ports or the PS/2 ports.
➋ Connect the display monitor to either the VGA port or the HDMI port.
➌ Plug in a CAT-6 UTP cable to the RJ-45 Gigabit LAN port, and connect the other end of
the cable to a switch connecting to the camera network.
➍ Plug in the speaker to the audio output port if necessary.
➎ Connect the power cable (with the power adapter) to the DC-in power jack. Then connect
them to a power outlet.
➏ The NVR then auto powers on when power source is connected.
➐ The LED lights blue when the NVR powers on.
➑ If serial data connection is needed, connect cables to these serial COM ports.
➒ Hit this power button to power on the system.
➊➋
➋ ➌
➎ ➊
➍
➑
➊ ➒➐
Hardware Quick Installation Guide
4
Install Hardware: M3000 Series
➊ Connect the keyboard and mouse:
- M3004: Connect them to the USB ports.
- M3004-IR: Connect the mouse to one of the USB ports and connect the
keyboard to one of the USB ports or to the purple PS/2 connector.
➋ Connect the display monitor to either the D-sub or DVI or HDMI port.
➌ Connect the power cord to the AC power socket at the rear panel of the unit.
➍ Plug in a CAT-6 UTP cable to the RJ-45 Gigabit LAN port, and connect the other end of
the cable to a switch that is connected to camera network.
➎ Plug in the speaker to the audio output port if necessary.
➏ The unit then auto powers on when the power cord is connected to power source.
* GVD isn’t responsible for any system malfunction if a 3rd-party application that isn’t certified by GVD is installed in the
system.
* M3004 (IR) series support decoding the resolution from D1 up to 20M.
* DO NOT plug any USB device except keyboard & mouse before the operating system starts.
6
1
3
4
52
4
1
3
5
2
Rear: M3004-IR Rear: M3004 Front
Hardware Quick Installation Guide 5
Install Hardware: M4006 & M4006-AR
➊ Connect the keyboard to one of the USB ports.
➋ Connect the mouse to one of the USB ports.
➌ Connect the display monitor to either the D-sub or DVI or HDMI port.
➍ Connect the power cord to the AC power socket at the rear panel of the unit.
➎ Plug in a CAT-6 UTP cable to the RJ-45 Gigabit LAN port, and connect the other end of
the cable to a switch connecting to the camera network.
➏ Plug in the speaker to the audio output port if necessary.
➐ The unit will auto power on once the power cord is connected to a power source.
* GVD isn’t responsible for any system malfunction if a 3rd-party application that isn’t certified by GVD is installed in the
system.
* M4006 and M4006-AR support decoding the resolution from D1 up to 20M.
* DO NOT plug any USB device except keyboard & mouse before the operating system starts.
1
623
4
57
Hardware Quick Installation Guide
6
Install Hardware: M4006-IR, M4008 & M4008-AR
* GVD isn’t responsible for any system malfunction if a 3rd-party application that isn’t certified by GVD is installed in the
system.
* M4006-IR, M4008 & M4008 AR support decoding the resolution from D1 up to 20M.
* DO NOT plug any USB device except keyboard & mouse before the operating system starts.
➊ Connect the keyboard and mouse to the USB ports either on the rear panel or on the front
panel. (The keyboard can also be connected to the purple PS/2 connector on the rear
panel.)
➋ Connect the display monitor to the VGA port or HDMI port.
➌ Plug in a CAT-6 UTP cable to the RJ-45 Gigabit LAN port, and connect the other end of
the cable to a switch that is connected to the network.
➍ Plug in the speaker to the audio output port if necessary.
➎ Connect the power cord to the AC power jack at the rear panel of the unit.
➏ The unit then auto powers on when the power cord is connected to power source.
➊
➊
➋
➌
➍
Power Button
Reset Button
➊
➎
Este manual sirve para los siguientes modelos
10
Tabla de contenidos
Otros manuales de DVR de GVD
