GVD M1142 Manual de usuario
GVD
Mobile NVR M1142
Quick Start Guide
Mobile NVR M1142 Quick Start Guide i
Contents
Contents ....................................................................... i
Preface .........................................................................ii
About this Document ......................................................... ii
Declaration of Conformity.................................................. ii
Copyright and Trademarks ................................................ ii
Hardware Requirements..............................................iii
Introduction.................................................................. 1
Accessories ................................................................. 2
Take a Tour .................................................................. 4
Front I/O Ports...................................................................4
Rear I/O Ports ...................................................................7
Onboard I/O Ports ...........................................................10
Install Hardware......................................................... 13
Open Pet Door ................................................................13
Install Internal SATA HDD/SSD .......................................14
Hot-swap a SATA HDD/SSD ...........................................16
Remove Bottom Cover ....................................................17
Install a WiFi Module .......................................................19
Install a SIM Card............................................................23
Install a 3G or 4G plus GPS Module (Optional) ..............24
Mount the Mobile NVR .............................................. 28
Wire DC-in Power Source ......................................... 30
Manage Ignition Power.............................................. 32
Wire Ignition Signal .........................................................32
Select Ignition Power Mode.............................................33
Set up Windows®...................................................... 34
Initialize HDDs........................................................... 35
Launch & Log in......................................................... 36
Use Installation Wizard.............................................. 37
Congure Network Parameters ................................. 44
Create Storage Volumes ........................................... 45
Auto-add a Camera ................................................... 46
Appendix. Install WiFi Device Driver & Connect WiFi
Network for the 1st Time............................................ 48
Appendix. Install 3G/4G Device Driver & Connect Mobile
Network for the 1st Time............................................ 51
Mobile NVR M1142 Quick Start Guide
ii
Preface
About this Document
This document is meant for the experienced users and integrators with hardware knowledge of personal
computers. If you are not sure about the description herein, consult your vendor before further handling.
We recommend that you keep one copy of this document for the quick reference for any necessary
maintenance in the future. Thank you for choosing GVD products.
Declaration of Conformity
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
CE
The product(s) described in this manual complies with all applicable European Union (CE) directives.
For computers systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE
compliance also requires proper cable and cabling techniques.
Copyright and Trademarks
This document contains proprietary information protected by copyright. All rights are reserved. No part
of this document may be reproduced by any mechanical, electronic, or other means in any form without
prior written permission of the manufacturer. Company/product names mentioned herein are used
for identification purposes only and are trademarks and/or registered trademarks of their respective
companies.
Mobile NVR M1142 Quick Start Guide iii
Hardware Requirements
Recording data is one of the most important parts for video surveillance, and hard disk drives are one of
the most important components to safely store the recording data.
It is always recommended that you use the hard disk drives certified by GVD. Find the list of the GVD-
certified hard disk drives at the link below:
http://www.gvdigital.com/gvdweb/html/document/Support_Lists/Certified%20HDD%20List.pdf
NOTE:
* GVD does not guarantee the system performance if a HDD model that is not certified by GVD is used.
* GVD recommends that you always use enterprise-level SATA hard drives for GVD enterprise NVR, Failover Server, Backup Server,
Extended Storage because it supports TLER (Time Limited Error Recovery), higher MTBF, higher Duty Cycles and typically include a
sensor for rotation and vibration.
Mobile NVR M1142 Quick Start Guide
iv
Mobile NVR M1142 Quick Start Guide 1
Introduction
Thank you for choosing GVD products. The M1142 is the mobile NVR
that comes in the rightful size among M1 Series, GVD's brand new line
of mobile NVRs. Powered by Intel®Celeron™ 1020E, the M1142 is a
fanless NVR to deliver fair CPU calculation with low power consumption.
The integrated Intel®HD Graphics 4000 Controller that brings DirectX11 also allows the NVRs to deliver
superb video and audio.
The M1142 comes with rich data connection including 3G/4G
and WiFi to stay tethered with the control center all the time. The
intelligent power management prevents startup failure and allows
the control center to watch over the car battery usage through 3G,
4G or WiFi. Isolated DIO on the other hand keeps the mobile NVR
connected with other in-vehicle devices such as a car door sensor,
and the change of DIO states can be sent to the control center.
If you opt for a GPS (plus 3G or 4G) module to go inside the mobile NVR, the control center can instantly
locate the vehicle that carries the mobile NVR on the map. Also on option is a G-sensor to measure the
vibration every couple of minutes and feed the data back to the control center. On the other hand the
mobile NVR is verified to be anti-shock and anti-vibration to guarantee more protection to the hard disk
drives onboard and ensures reliable video recording.
Four PoE LAN ports are featured on the M1142. Each port delivers power up to 25.5W and simultaneously
transfers data up to 1000 Mbps over a single CAT-6 cable. The
highly integrated mechanical design on the other hand allows
the M1142 to efficiently distribute the heat generated by the PoE
circuit and therefore makes the M1142 a very stable fanless NVR
with PoEs. The mechanical design is also modular to make the
NVR easy-to-install and maintain.
The simple and sturdy design makes the M1142 ideal for all kinds
of vehicles. It is your best choice for IP video surveillance on the
go.
Product Highlights
■Power over Ethernet
■Anti-shock / anti-vibration
■Rich data connections
■Intelligent power management
■Isolated DIO
Mobile NVR M1142 Quick Start Guide
2
Accessories
Driver CD &
User's Manual
DRIVERS
User’s
Manual
Terminal
Block
1 x 3-pin male terminal block
for 8~35VDC output
WiFi Module Kit
SparkLAN WPER-172GN 802.11b/g/n USB Half Mini Card
■802.11b/g/n ISM Band: 2.400 ~ 2.4835GHz
■Antenna: 2 x U.FL connectors (diversity antenna), 1T1R
1 x External Antenna
■RP-SMA male body & female inner contact
A few screws to x the module
■Stainless-steel round philips screws
Wall-mount Kit
■1 wall-mount bracket
■8 x rubber bumpers
■8 x M4 screws
Thermal Pad
One piece of thermal pad for internal SATA
HDD/SSD
Power Adapter (Optional)
24V/6.67A 160W AC/DC adapter
(for +8~35VDC output)
Internal HDD/SSD Screws
A number of screws to x the internal HDD/SSD
■Stainless-steel round philips screws
Outside-accessible HDD/SSD Keys
Two keys to the door to the outside-accessible and hot-swappable HDD/SSD SATA port
Mobile NVR M1142 Quick Start Guide 3
Accessories
Region Module (w/ GPS capability) & Wire External Antenna
4G+GPS
Module Kit
(Optional)
Southeast
Asia, Middle
East & partly
India (1800
MHz only)
Sierra Wireless® AirPrime™ MC7304
w/ 15cm internal wire
■LTE-FDD / HSPA+ (B1, B2, B3, B5,
B7, B8, B20)
1 x 3G or 4G External
Antenna
■RP-SMA male body & male
inner contact
1 x GPS External Antenna
■Length: 300cm
■RP-SMA male body & male
inner contact
A few screws to x the
module
■Stainless-steel round philips
screws
North America
& Latin
America
Sierra Wireless® AirPrime™ MC7354
w/ 15cm internal wire
■LTE-FDD, HSPA+, GSM/GPRS/EDGE,
GSM/GPRS/EDGE, CDMA (B1, B2,
B4, B5, B8, B13, B17, B25, BC0, BC1,
BC10)
3G+GPS
Module Kit
(Optional) All regions
HUAWEI MU609 Mini-PCIe
■HSPA+/UMTS quad-band
850/900/1900/2100 MHz
■GSM/GPRS quad-band
850/900/1800/1900 MHz
Sierra Wireless® AirPrime™ MC8705
w/ 15cm internal wire
■Operational bands: WCDMA 850,
WCDMA 900, WCDMA 1900, WCDMA
2100
Mobile NVR M1142 Quick Start Guide
4
Take a Tour
Front I/O Ports
Power
button DVI-I
connector
Hot-
swappable
HDD slot
Line-out
Reset
button
Status
LEDs COM2
Wireless
Status LEDs
USB 3.0
ports
COM1
Mic-in
Title Description
Power button
Turns on/off the system. Hit this button to turn on the system. Hit this button again to power off the system. Press-
and-hold this button to force system shutdown.
There must be no less than 5 seconds between each power on/off.
The PWR status LED lights green when the system is powered on.
Reset button
Restarts the system without turning off the power.
To prevent false trigger, this button is recessed in the front panel. Use an object with a pointed end to hit this
button.
Status LEDs
Deliver the states of some system parts:
Printed Text Color Description
PWR Green Lights when the system is powered on.
HDD Red Lights when the SATA HDD is being accessed.
WDT Yellow Blinks when the watchdog timer is started.
IGN Green Lights when ignition signal is received.
Tabla de contenidos
Otros manuales de DVR de GVD
