Guardian Fall Protection 61133 Manual de usuario

Product Name: Universal Guardrail Post

Instruction Manual

Part #: 61133; 61135; 61136

Do not throw away these instructions!

Read and understand these instructions before using equipment!

Introduction 1

Applicable Safety Standards 1

Worker Classifications 1

Safety Information 5

Product Specific Applications 2

Components and Specifications 2

Maintenance, Cleaning, and Storage 4

Inspection 4

Installation and Use 3

Inspection Log 4

Labels 6

Introduction

Thank you for purchasing a Guardian Fall

Protection Universal Guardrail Post. This

manual must be read and understood in

its entirety, and used as part of an

employee training program as required

by OSHA or any applicable state agency.

This and any other included instructions

must be made available to the user of the

equipment. The user must understand how

to safely and effectively use the Universal

Guardrail Post, and all fall safety equipment

used in combination with the Universal

Guardrail Post.

User Information

Date of First Use:

Serial #:

Trainer:

User:

Applicable Safety Standards

When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926

Subpart M and OSHA 1910 standards for fall protection. Applicable standards and regulations depend on the

type of work being done, and also might include state-specific regulations. Consult regulatory agencies for

more information on fall protection systems and associated components.

Worker Classifications

CAUTION

Understand the following definitions of those who

work near or who may be exposed to fall hazards.

Qualified Person: A person with an accredited degree or certification, and with extensive experience or

sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall

protection and rescue systems.

Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be

responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,

and application. A person who is proficient in identifying existing and predictable fall hazards, and who has

the authority to stop work in order to eliminate hazards.

Authorized Person: A person who is assigned by their employer to work around or be subject to potential or

existing fall hazards.

It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all

applicable safety regulations are complied with.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Components and Specifications

Product Specific Applications

Use of equipment in unintended applications may result in serious

injury or death. NEVER make any connections to guardrail systems.

WARNING

NEVER lean or climb on guardrail systems.

WARNING

Surfaces more than 6’ above lower levels require the use

of a Fall Prevention or Fall Protection system.

Materials: powder-coated steel.

Part # Size Description

61133

61135

61136

52”

65”

74”

Universal Guardrail Post

Fall Prevention: Universal Guardrail Post may be used in Fall Prevention applications ONLY. Fall

Prevention Systems are placed around the leading edges of any and all fall hazards to prevent a

worker from going over an edge, and may be used in substitute of Fall Protection or safety

netting systems. Installation requirements for Universal Guardrail Posts set forth in this manual

MUST be adhered to. Personal Fall Arrest, Work Positioning, Climbing, Rescue, and any other

systems must NEVER be connected to Fall Prevention Systems.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Installation and Use

Prior to use, plan your system:

1. All leading edges of fall hazards must be blocked, or a supplemental Fall Protection system MUST be used

in combination with, but never connected to, the applicable Fall Prevention system.

2. Selected work area must be free of all hazards, including, but not limited to, debris, rot, decay, cracking,

and hazardous materials. NEVER install guardrail system on top of gravel or other loose or slippery surfaces.

3. Lay out the job by measuring and spacing the location of Universal Guardrail Posts on the work surface.

Failure to properly measure and plan ahead may result in having to move and reinstall system components.

Universal Guardrail Post rungs must face in towards work surface.

4. Universal Guardrail Posts may be spaced a MAXIMUM of 8’ apart. Guardrail systems must be installed a

MINIMUM 10’ from power lines and all other electrical hazards.

5. All Universal Guardrail Posts, guardrails, baseplates/guardrail receivers, and all other equipment must be

selected and deemed compatible by a Competent Person. All guardrails MUST be compatible 2” x 4“ or 2” x 6“

construction grade lumber, compatible snap-on metal rails, or compatible galvanized steel cable. Lumber

guardrails must overlap a minimum 12” on each end.

6. Toprails must be 42” (+/- 3”) above the work surface or, if used in stilt work applications, 42” plus height

of stilts. Toprails must withstand a minimum 200 lb. downward or outward force.

7. Midrails must be halfway between the top edge of the guardrail system and the working level (not the

toeboard). Midrails must withstand a minimum 150 lb. downward or outward force.

8. All intermediary rails (not the toprail or the midrail) must not allow for gaps greater than 19”.

9. Toeboards are REQUIRED on surfaces with slopes more than 4/12 (vertical/horizontal), and/or if a risk

exists for tools, equipment, materials, or other substances to fall down to a lower level. Toeboards must be a

minimum 3½” from their top edge to the work surface, and must not have greater than ¼” clearance

between their bottom edge and the work surface. Toeboards must withstand a minimum 50 lb. downward or

outward force.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Maintenance, Cleaning, and Storage

If Universal Guardrail Post fails inspection in any way, immediately remove it from service, and contact

Guardian to inquire about its return or repair.

Cleaning after use is important for maintaining the safety and longevity of Universal Guardrail Post. Remove

all dirt, corrosives, and contaminants from Universal Guardrail Post before and after each use. If Universal

Guardrail Post cannot be cleaned with plain water, use mild soap and water, then rinse and wipe dry. NEVER

clean Universal Guardrail Post with corrosive substances.

When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,

or other degrading elements.

Prior to EACH use, inspect Universal Guardrail Post for deficiencies, including, but not limited to, corrosion,

deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating,

alteration, and missing or illegible labels. IMMEDIATELY remove Universal Guardrail Post from service if defects

or damage are found, or if exposed to forces of fall arrest.

Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot, rust, decay,

cracking, and hazardous materials. Ensure that selected work area will support the application-specific

minimum loads set forth in this instruction manual. Work area MUST be stable.

At least every 6 months, a Competent Person other than the user must inspect Universal Guardrail Post.

Competent Person inspections MUST be recorded in inspection log in instruction manual and on

equipment inspection grid label. The Competent Person must sign their initials in the box

corresponding to the month and year the inspection took place.

During inspection, consider all applications and hazards Universal Guardrail Post has been subjected to.

Inspection

Inspection Log

If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE.

Date of First Use: __________________.

Product lifetime is indefinite, as long as it passes pre-use and Competent Person inspections. User must

inspect prior to EACH use. Competent Person other than user must complete formal inspection at least

every 6 months. Competent Person to inspect and initial.

This inspection log must be specific to one Universal Guardrail Post. Separate inspection logs must be

used for each Universal Guardrail Post. All inspection records must be made visible and available to all

users at all times.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Safety Information

Failure to understand and comply with safety regulations may result in

serious injury or death. Regulations included herein are not all-inclusive,

are for reference only, and are not intended to replace a Competent

Person’s judgment or knowledge of federal or state standards.

WARNING

Do not alter equipment. Do not misuse equipment.

Workplace conditions, including, but not limited to, flame, corrosive chemicals, electrical shock, sharp objects,

machinery, abrasive substances, weather conditions, and uneven surfaces, must be assessed by a Competent

Person before fall protection equipment is selected.

The analysis of the workplace must anticipate where workers will be performing their duties, the routes they

will take to reach their work, and the potential and existing fall hazards they may be exposed to. Fall

protection equipment must be chosen by a Competent Person. Selections must account for all potential

hazardous workplace conditions. All fall protection equipment should be purchased new and in an unused

condition.

Fall protection systems must be selected and installed under the supervision of a Competent Person, and used

in a compliant manner. Fall protection systems must be designed in a manner compliant with all federal, state,

and safety regulations. Forces applied to anchors must be calculated by a Competent Person.

Unless explicitly stated otherwise, the maximum allowable free fall distance for lanyards must not exceed 6’.

No free fall allowed for non-LE SRLs. Class A SRLs must arrest falls within 24”; Class B SRLs must arrest falls

within 54”.

Harnesses and connectors selected must be compliant with manufacturer’s instructions, and must be of

compatible size and configuration. Snap hooks, carabiners, and other connectors must be selected and applied

in a compatible fashion. All risk of disengagement must be eliminated. All snap hooks and carabiners must be

self-locking and self-closing, and must never be connected to each other.

A pre-planned rescue procedure in the case of a fall is required. The rescue plan must be project-specific. The

rescue plan must allow for employees to rescue themselves, or provide an alternative means for their prompt

rescue. Store rescue equipment in an easily accessible and clearly marked area.

Training of Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use equipment

must be provided by a Competent Person. Training must include the ability to recognize fall hazards, minimize

the likelihood of fall hazards, and the correct use of personal fall arrest systems.

NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or equipment, unless

explicitly certified for such use.

Equipment subjected to forces of fall arrest must immediately be removed from use.

Age, fitness, and health conditions can seriously affect the worker should a fall occur. Consult a doctor if there

is any reason to doubt a user’s ability to withstand and safely absorb fall arrest forces or perform set-up of

equipment. Pregnant women and minors must not use this equipment.

Physical harm may still occur even if fall safety equipment functions correctly. Sustained post-fall suspension

may result in serious injury or death. Use trauma relief straps to reduce the effects of suspension trauma.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

685247 (Rev. B)

Labels

Compliant with

OSHA 1910

and 1926

regulations.

Universal

Guardrail Post

6305 S. 231st St.

Kent, WA 98032

1-800-466-6385

Date of

manufacture:

Made in China

Follow the

manufacturer’s

instructions

included with

equipment

at time of

shipment.

WARNING

Guardrail rungs

MUST face in

toward work

surface.

Lumber

guardrails

MUST overlap

a MINIMUM

of 12”.

90450 (Rev. A)

Part #:

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de seguridad de Guardian Fall Protection

Guardian Fall Protection

Guardian Fall Protection 00370 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection G-Lok Guía

Guardian Fall Protection

Guardian Fall Protection SSMR G-Rail Base Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 30800 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Arc-O-Pod Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 00432 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 00260 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Snappy Anchor 00710 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Halo Web SRL Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 15026 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection EcoAnchor Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 00691 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 01500 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 00342 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Edge Angel SRL Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Diablo 2.0 Tie-Back SRL Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 10947 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Edge Series Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 10920CSA Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 10829 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 00484 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 10733 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Bull Ring Anchor Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Armadillo Manual de usuario

Manuales populares de Equipo de seguridad de otras marcas

Innova

Innova Xtirpa Manual de instrucciones

bolle SAFETY

bolle SAFETY B810 Manual de usuario

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manual de usuario

Hiltron security

Hiltron security POWER8E Guía

Hatco

Hatco B-950P Manual de usuario

Sitec

Sitec TX MATIC Manual de usuario

TEUFELBERGER

TEUFELBERGER GRIP 12 Manual de usuario

MSA

MSA PremAire System Manual de usuario

AMC

AMC 1022M Series Manual de usuario

Trinity

Trinity CASS S3 Manual de usuario

CMC

CMC Helitack HotSeat Manual de usuario

Force

Force P-35 Manual de usuario

ACM

ACM SAFETY D200 Manual del producto

Honeywell

Honeywell Miller H-Design DuraFlex Manual del operador

ROCK

ROCK P-451 AS Manual de usuario

Power first

Power first 2XYR7A Manual de servicio

SCHUBERTH

SCHUBERTH SHP 28-C Manual de usuario

Trango

Trango CINCH Manual de usuario