Guardian Fall Protection 10947 Manual de usuario

Product Name: G-Link SRL

Instruction Manual

Part #: 10947; 10993; 10994; 10995; 10996; 10997; 10998

Do not throw away these instructions!

Read and understand these instructions before using equipment!

Introduction 1

Applicable Safety Standards 1

Worker Classifications 1

Safety Information 6

Product Specific Applications 2

Limitations 2-3

Components and Specifications 3

Maintenance, Cleaning, and Storage 4

Inspection 5

Installation and Use 4

Inspection Log 5

Labels 7

Introduction

Thank you for purchasing a Guardian Fall

Protection G-Link SRL. This manual must be

read and understood in its entirety, and

used as part of an employee training

program as required by OSHA or any

applicable state agency.

This and any other included instructions

must be made available to the user of the

equipment. The user must understand how

to safely and effectively use the G-Link SRL,

and all fall safety equipment used in

combination with the G-Link SRL.

User Information

Date of First Use:

Serial #:

Trainer:

User:

Applicable Safety Standards

When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926

Subpart M, OSHA 1910, ANSI Z359.14-2014, and ANSI A10.32-2012 standards for fall protection. Applicable

standards and regulations depend on the type of work being done, and also might include state-specific

regulations. Consult regulatory agencies for more information on fall protection systems and associated

components.

Worker Classifications

CAUTION

Understand the following definitions of those who

work near or who may be exposed to fall hazards.

Qualified Person: A person with an accredited degree or certification, and with extensive experience or

sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall

protection and rescue systems.

Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be

responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,

and application. A person who is proficient in identifying existing and predictable fall hazards, and who has

the authority to stop work in order to eliminate hazards.

Authorized Person: A person who is assigned by their employer to work around or be subject to potential or

existing fall hazards.

It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all

applicable safety regulations are complied with.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Product Specific Applications

Personal Fall Arrest: G-Link SRL may be used to support a MAXIMUM 1 Personal Fall Arrest System

(PFAS) for use in Fall Arrest applications. Structure must withstand loads applied in the directions

permitted by the system of at least 5,000 lbs. No free fall is permitted. Applicable D-ring: Dorsal.

Restraint: G-Link SRL may be used in Restraint applications. Restraint systems prevent workers

from reaching the leading edge of a fall hazard. Always account for fully deployed length of

lanyard/SRL. Structure must withstand loads applied in the directions permitted by the system of

at least 1,000 lbs. No free fall is permitted. Restraint systems may only be used on surfaces with

slopes up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal, Chest, Side, Shoulder.

WARNING

Use of equipment in unintended applications may result in serious

injury or death. Maximum 1 attachment per connection point.

For all applications: worker weight capacity range

(including all clothing, tools, and equipment) is 130-310 lbs.*

* Maximum capacity may be increased to 420 lbs. if used in combination

with Guardian Shock Absorber Extension (part # 01205).

Limitations

Fall Clearance: There must be

sufficient clearance below the

anchorage connector to arrest

a fall before the user strikes

the ground or an obstruction.

When calculating fall clearance,

account for a MINIMUM 3’

safety factor, deceleration

distance, user height, length

of lanyard/SRL, harness stretch,

and all other applicable factors.

Diagram shown is an example

fall clearance calculation ONLY.

Swing Falls: Prior to installation

or use, make considerations for

eliminating or minimizing all

swing fall hazards. Swing falls

occur when the anchor is not

directly above the location

where a fall occurs. Always

work as close to in line with

the anchor point as possible.

Swing falls significantly increase

the likelihood of serious injury

or death in the event of a fall.

Fall clearance calculation shown based on standing worker falling

directly in-line with anchor point. Always consider potential swing fall

and other hazards when calculating fall clearance.

*Eliminate Swing Fall whenever possible!

If Swing Fall exists, always account

for additional fall clearance.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Components and Specifications

Compatibility: When making connections with G-Link SRL, eliminate all possibility of roll-out. Roll-out occurs

when interference between a hook and the attachment point causes the hook gate to unintentionally open

and release. All connections must be selected and deemed compatible with G-Link SRL by a Competent Person.

All connector gates must be self-closing and self-locking, and withstand minimum loads of 3,600 lbs. See the

following for examples of compatible/incompatible connections:

Connector

closed and

locked to

D-ring. OK.

Two or more

snap hooks or

carabiners

connected to

each other. NO.

Two connectors

to same

D-ring. NO.

Connector

directly to

horizontal

lifeline. NO.

Connector

to integral

lanyard.

NO.

Connector

directly to

webbing.

NO.

Incompatible

or irregular

application,

which may

increase risk

of roll-out. NO.

Materials: Nylon, stainless steel, and aluminum.

Part # Length Description

10993

10994

6’

11’

G-Link Dual 6’ Retractable System With Aluminum Snap Hooks

G-Link Dual 11’ Retractable System With Aluminum Snap Hooks

10995

10996

10997

11’

6’

11’

G-Link Dual 11’ Retractable System With Steel Rebar Hooks

G-Link Dual 6’ Retractable System With Steel Rebar Hooks

G-Link Dual 11’ Retractable System With Aluminum Rebar Hooks

10998 6’ G-Link Dual 6’ Retractable System With Aluminum Rebar Hooks

n/a G-Link Connector Bracket w/High Strength Carabiner10947

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Maintenance, Cleaning, and Storage

If G-Link SRL fails inspection in any way, immediately remove it from service, and contact Guardian to

inquire about its return or repair.

Cleaning after use is important for maintaining the safety and longevity of G-Link SRL. Remove all dirt,

corrosives, and contaminants from G-Link SRL before and after each use. If G-Link SRL cannot be cleaned

with plain water, use mild soap and water, then rinse and wipe dry. NEVER clean G-Link SRL with corrosive

substances.

When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,

or other degrading elements.

Installation and Use

G-Link SRL MUST NEVER be used in Leading Edge (LE) applications.

No free fall is allowed.

ALWAYS avoid lifeline contact with sharp or abrasive edges and surfaces.

In Fall Arrest applications, SRL must always be positioned at

or above harness dorsal D-ring AND at or below anchor point.

1. All components of the personal fall arrest system must be selected and deemed compatible with G-Link by

a Competent Person.

2. Ensure structure to which SRL is to be attached, and on which work is to be performed, is free of all

hazards, including, but not limited to, debris, rot, rust, sharp or abrasive edges and surfaces, and hazardous

materials.

3. G-Links are primarily intended for use in mobile applications. Use a compatible carabiner to connect G-Link

Carabiner Connection Point to user harness dorsal D-ring. NEVER attach G-Link snap hooks or rebar hooks to

harness when used in this manner.

4. Attach G-Link snap hook or rebar hook to a compatible anchorage connector. NEVER make connections to

anchorages that will allow harness dorsal D-ring to be positioned above anchor point.

*If using SRL with rebar hook configuration, rebar hooks must ONLY be connected to compatible

structural rebar.

5. Ensure 100% tie-off will be maintained at all times; ALWAYS attach disengaged snap hook or rebar hook to

a compatible anchorage connector prior to unhooking engaged snap hook or rebar hook.

* G-Links configured with snap hooks may also be used in stationary applications, with the Carabiner

Connection Point attached with a compatible carabiner to an anchorage connector at or above the harness

dorsal D-ring. The snap hook of one lifeline leg may then be attached to a harness D-ring compatible with the

application. NEVER attach both lifeline legs to the harness. NEVER attach rebar hooks to the harness at any

time. G-Link for MAXIMUM 1 worker ONLY.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Inspection

Inspection Log

If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE.

Date of First Use: __________________.

Product lifetime is indefinite, as long as product passes all inspection requirements. User must inspect

prior to EACH use. Competent Person other than user must complete formal inspection at least every

6 months. Competent Person to inspect and initial.

This inspection log must be specific to one G-Link SRL. Separate inspection logs must be used for

each G-Link SRL. All inspection records must be made visible and available to all users at all times.

KEEP INSTRUCTIONS AVAILABLE FOR REFERENCE. Record Date of First Use.

Prior to EACH use, inspect G-Link SRLs for deficiencies, including, but not limited to, corrosion, deformation,

pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, broken

stitching, fraying, bird-caging, and missing or illegible labels. Inspect full length of lifeline. IMMEDIATELY

remove G-Link SRL from service if defects or damage are found, or if exposed to forces of fall arrest.

Prior to EACH use, check G-Link SRL lifeline retraction by pulling out a minimum 4’ and allowing it to retract

under light tension; lifeline must retract completely. Pull lifeline sharply to test braking function; brakes must

engage. Check shock pack for signs of deployment and/or fall arrest indicator for signs of activation.

IMMEDIATELY remove from service if G-Link SRL does not function properly, or if any evidence of exposure to

forces of fall arrest exists.

Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot, rust, decay,

cracking, and hazardous materials. Ensure that selected work area will support the application-specific

minimum loads set forth in this instruction manual. Work area MUST be stable.

Every 6 months, a Competent Person other than the user must inspect G-Link SRLs. Competent Person

inspections MUST be recorded in inspection log in instruction manual and on equipment inspection

grid label. The Competent Person must sign their initials in the box corresponding to the month and

year the inspection took place.

During inspection, consider all applications and hazards G-Link SRLs have been subjected to.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

Safety Information

Failure to understand and comply with safety regulations may result in

serious injury or death. Regulations included herein are not all-inclusive,

are for reference only, and are not intended to replace a Competent

Person’s judgment or knowledge of federal or state standards.

WARNING

Do not alter equipment. Do not misuse equipment.

Workplace conditions, including, but not limited to, flame, corrosive chemicals, electrical shock, sharp objects,

machinery, abrasive substances, weather conditions, and uneven surfaces, must be assessed by a Competent

Person before fall protection equipment is selected.

The analysis of the workplace must anticipate where workers will be performing their duties, the routes they

will take to reach their work, and the potential and existing fall hazards they may be exposed to. Fall

protection equipment must be chosen by a Competent Person. Selections must account for all potential

hazardous workplace conditions. All fall protection equipment should be purchased new and in an unused

condition.

Fall protection systems must be selected and installed under the supervision of a Competent Person, and used

in a compliant manner. Fall protection systems must be designed in a manner compliant with all federal, state,

and safety regulations. Forces applied to anchors must be calculated by a Competent Person.

Unless explicitly stated otherwise, the maximum allowable free fall distance for lanyards must not exceed 6’.

No free fall allowed for non-LE SRLs. Class A SRLs must arrest falls within 24”; Class B SRLs must arrest falls

within 54”.

Harnesses and connectors selected must be compliant with manufacturer’s instructions, and must be of

compatible size and configuration. Snap hooks, carabiners, and other connectors must be selected and applied

in a compatible fashion. All risk of disengagement must be eliminated. All snap hooks and carabiners must be

self-locking and self-closing, and must never be connected to each other.

A pre-planned rescue procedure in the case of a fall is required. The rescue plan must be project-specific. The

rescue plan must allow for employees to rescue themselves, or provide an alternative means for their prompt

rescue. Store rescue equipment in an easily accessible and clearly marked area.

Training of Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use equipment

must be provided by a Competent Person. Training must include the ability to recognize fall hazards, minimize

the likelihood of fall hazards, and the correct use of personal fall arrest systems.

NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or equipment, unless

explicitly certified for such use.

Equipment subjected to forces of fall arrest must immediately be removed from use.

Age, fitness, and health conditions can seriously affect the worker should a fall occur. Consult a doctor if there

is any reason to doubt a user’s ability to withstand and safely absorb fall arrest forces or perform set-up of

equipment. Pregnant women and minors must not use this equipment.

Physical harm may still occur even if fall safety equipment functions correctly. Sustained post-fall suspension

may result in serious injury or death. Use trauma relief straps to reduce the effects of suspension trauma.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com

785077 (Rev. F)

Labels

G-Link

SRL Attachment SRL Attachment

FALL ARREST

ATTACHMENT.

ONLY USE ANSI

Z359.12-09

CARABINER. 800-466-6385

6305 S. 231st St.

Kent, WA 98032

DO NOT REMOVE LABELS

Part #: 10947; 10993; 10994; 10995; 10996; 10997; 10998

ANSI Z359.1-07,

ANSI A10.32-12

OSHA 1926 Subpart M,

OSHA 1910

90061 (Rev. B)

COMPETENT

PERSON MUST

ENSURE

COMPATIBILITY OF

ALL COMPONENTS.

READ AND FULLY

UNDERSTAND

ALL INSTRUCTIONS

BEFORE USE; FAILURE TO

DO SO MAY RESULT IN SERIOUS INJURY OR DEATH! ATTACH

RETRACTABLES DIRECTLY TO THIS BRACKET. DO NOT USE ANY

COMPONENT BETWEEN THE RETRACTABLE AND THIS BRACKET.

Capacity:

1 person,

130-310 lbs.

(including all

equipment), or up

to 420 lbs.

*see instructions.

Bracket Material:

Zinc-Plated Steel

WARNING

WARNING: Manufacturer's

instructions supplied with this

product at time of shipment

must be read prior to use.

Instructions must be followed

for proper use, maintenance, and

inspection. Alterations or misuse of

this product, or failure to follow instructions,

may result in serious injury or death.

NOT REPAIRABLE.

DO NOT REMOVE THIS LABEL.

USE: No free fall is allowed. SRL must always be

positioned at or above harness D-ring. Avoid

lifeline contact with sharp edges. For use by trained

persons only. This device is only for use by

one person as a fall arrester. Ensure

connection to anchorage is secured

properly before use. Not suitable for

horizontal use. May be used as a

component of a PFAS in HLL applications.

Design, installation, and utilization of HLLs

must be supervised by a Qualified Person.

Serial #Part #

Mfg. Date (mo/yr)

_____/_____

Date of First Use

INSPECTION: Prior to each

use, inspect device per user

manual, including locking

function (pull sharply to test),

retraction function, legibility of

labels, evidence of defects,

damage, or missing parts, and

condition of connectors, housing, fasteners, and

lifeline (inspect full length). Inspection by

Competent Person required at least every 6

months. Immediately remove from service if

evidence of shock pack deployment is found.

SPECIFICATIONS:

Average arresting force: 900 lbs.

Max. arresting distance: 54”

Max. capacity: 130 - 310 lbs.

Webbing: 11’ Dyneema, 1" width

Class B SRL

STANDARDS:

OSHA 1910 & OSHA 1926 Subpart M

ANSI Z359.14-2014 & ANSI A10.32-2012

Made in Taiwan

90001 (Rev. F)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de seguridad de Guardian Fall Protection

Guardian Fall Protection

Guardian Fall Protection 30800 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 00691 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection G-Lok Guía

Guardian Fall Protection

Guardian Fall Protection CB-18 Anchor Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 10974 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 01500 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Halo SRL-LE Manual de usuario

Guardian Fall Protection

Guardian Fall Protection GR6 Tie-Back SRL Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 10829 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Edge Series Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Rapid Deployment Rescue Ladder Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 10733 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Armadillo Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 53221 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 01520 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 00260 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Diablo 2.0 Tie-Back SRL Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 10920CSA Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Halo Web SRL Manual de usuario

Guardian Fall Protection

Guardian Fall Protection C-Slab Grabber Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 00370 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 00484 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection 10705 Manual de usuario

Guardian Fall Protection

Guardian Fall Protection Cable LE Lanyard Manual de usuario

Manuales populares de Equipo de seguridad de otras marcas

Innova

Innova Xtirpa Manual de instrucciones

bolle SAFETY

bolle SAFETY B810 Manual de usuario

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manual de usuario

Hiltron security

Hiltron security POWER8E Guía

Hatco

Hatco B-950P Manual de usuario

Sitec

Sitec TX MATIC Manual de usuario

TEUFELBERGER

TEUFELBERGER GRIP 12 Manual de usuario

MSA

MSA PremAire System Manual de usuario

AMC

AMC 1022M Series Manual de usuario

Trinity

Trinity CASS S3 Manual de usuario

CMC

CMC Helitack HotSeat Manual de usuario

Force

Force P-35 Manual de usuario

ACM

ACM SAFETY D200 Manual del producto

Honeywell

Honeywell Miller H-Design DuraFlex Manual del operador

ROCK

ROCK P-451 AS Manual de usuario

Power first

Power first 2XYR7A Manual de servicio

SCHUBERTH

SCHUBERTH SHP 28-C Manual de usuario

Trango

Trango CINCH Manual de usuario