GT GT8 Manual de usuario
Page 1
Version 1.1 January 2021
GT8 Terminal
User Guide
Disclaimer
Copyright © 2021, Grosvenor Technology Ltd. All rights reserved.
All brands, names, or trademarks appearing in this document are acknowledged as the trademarks of their
respective owners.
No part of this document may be reproduced in any form or by any means for any purpose without the
written permission of Grosvenor Technology.
Whilst we make every eort to ensure the accuracy of our publications, Grosvenor Technology assumes no
responsibility or liability for any errors or inaccuracies that may appear in this document.
www.gtclocks.com
Page 2
Contents
Preface 5
Certications 6
BatteryLife 6
Maintenance 6
Cleaning 6
InstallationSafety 6
WEEE 7
About the GT8 Terminal 7
About this Guide 7
RelatedDocuments 7
TechnicalSupport 7
Europe,MiddleEastandAfrica 7
NorthAmerica 7
Hardware Specication 8
Display 8
Processor 8
OperatingSystem 8
Input/Output 8
Memory 8
Internal Persistent Storage 8
HostConnectivity 8
Power 8
OperatingTemperature&Humidity 9
PlugandPlayDeployment 9
Integration 9
Sound 9
Camera 9
PhysicalSecurity 9
Page 3
Contents
Dimensions 9
Sustainability 9
Reader Modules 10
ExpansionModules 11
Comms Modules 11
BiometricModules 11
Software 12
Installation 13
Fitting the Terminal 13
Location: 13
Power Options 14
AC110-240VviaAdapter 14
DC 12V 14
PoweroverEthernetPoE 14
BatteryBackup 15
Installing Optional Modules 16
FrontPlate 16
FittingInternalFingerprintReaderModule 17
FittingProximityorCardSwipeReaderModules 18
FittingtheWi-FiModule 19
Page 4
Contents
System Start-up 20
TerminalSetupNavigation 20
Terminal Shut Down 21
Terminal Recovery 22
Software Reset 22
RecoveryMenu 22
Terminal Setup 23
AccessingtheTerminalSetup 23
ConguringNetworkSettings 24
EnableandCongureWi-Fi 24
CongureWiredNetworks 25
ConguringReaders 26
WiegandBitmask 27
ParityMask 27
Testing Card Readers 28
Testing the Camera 28
TestingBiometricReader 29
Terminal Health Information 30
Software Deployment 31
DeploymentfromUSBmemorydevice 31
ApplicationSetup 32
Care and Maintenance 33
MaintenanceInstructions 33
Page 5
Preface
Important Note:
Menus and options will vary depending on the hardware
options supplied and software version installed. Please
refer to additional instructions supplied with your terminal
for additional information.
Page 6
Preface
Certications
The GT8 has been certied for use in the following markets
Europe CE Certication
USA FCC, UL 62368-1
India BIS Certication
In addition, the clock has been certied to comply with the requirements of the CB certication authority
which may meet compliance requirements in their member countries. For further information regarding CB
certication please see www.iecee.org/dyn/www/f?p=106:40:0 , or discuss with Grosvenor Technology’s
professional services team.
If the GT8 is intended to be used in countries other than those listed above, please contact Grosvenor
Technology’s professional services team to discuss how we can assist with certication.
Battery Life
The GT8 terminal is tted with a Lithium-Ion battery which typically has a service life of between 3 and 5
years. In order to ensure the continued reliable operation of the back-up battery function we recommend
regularly checking the condition of the battery and replacing it when it has reached the end of its service life.
The GT8 is also tted with a button cell type battery on the main PCB to maintain the real-time clock (RTC)
of the device when power is removed. This battery typically has a service life of around 10 years. The
battery should only be replaced by suitably qualied engineers and care should be taken to avoid damage to
the PCB caused by ESD (ElectroStatic Discharge). Replacement batteries must be of the same type as the
original, and the old battery should be disposed of in accordance with local regulations.
Care should be taken when recycling the terminal to ensure that the batteries are removed and recycled in
accordance with local regulations/legislation.
Maintenance
The GT8 terminal does not require any regular maintenance during its service life.
It is however recommended that periodically (once every 6 months) the condition of the battery should be
checked to see if there are signs that it’s reaching the end of its life. Occasionally, the battery may start
to swell towards the end of its life, if this is noticed, the battery should be replaced (Part Number: EM-BB-
2HR-A).
Cleaning
Cleaning of the outside of the terminal can be undertaken at intervals appropriate to the environment
that it is being used and the frequency of use. In all cases it is recommended that the surface of the
clock is wiped with a lint free cloth that has been dampened with up to 70% isopropyl alcohol. We do not
recommend spraying liquids directly onto the surface of the clock as this could potentially cause damage to
the electronics. Particular care should be taken when cleaning the display and biometric devices to prevent
damage.
Installation Safety
The GT8 clock should be installed in accordance with the instructions documented in this user guide. The
clock should be installed in compliance with any Health and Safety legislation and it is recommended that
any electrical or network connections to the clock are undertaken by a suitably qualied engineer.
The GT8 clock is designed to be installed indoors only with a normal ambient operating temperature
between 0-35 Deg C (32-95 Deg F).
i
!
Page 7
Preface
About the GT8 Terminal
GT8 is more than just a next generation time and attendance terminal - it’s designed to open up a world of
possibilities for wider integration with Human Resources Management Systems (HRMS) and a myriad of
potential new applications beyond workforce management.
About this Guide
This User Guide is intended for users who will be responsible for installing and conguring the GT8 terminal.
This guide was written with the following rmware, application and optional modules installed.
Firmware: v2.0.0
Application: GTEasyClock v2.0.0
RM-LUM-M320-GT8 Fingerprint reader
RM-HID-B Prox/card reader
CM-WIFI-M2-22 Wi-Fi module
Related Documents
You should also refer to the following documents, available from Grosvenor Technology:
GT API Reference Manual - This document is targeted at software developers writing Android applications
for the GT8 terminal.
Application User Guide - Relevant to your application.
Technical Support
Technical Support can be obtained from Grosvenor Technology from the following points of contact:
Europe, Middle East and Africa
Phone: +44 (0)1202 627611
E-mail: HCM-EMEAsupport@grosvenortechnology.com
Website: www.grosvenortechnology.com
North America
Phone: +1 800.989.5197
E-mail: HCM-USsupport@grosvenortechnology.com
Website: www.gtclocks.com
Care should be taken when installing the clock to ensure that it does not present any possible hazards to
people or property within its vicinity. The clock should be installed at a height that ensures compliance with
any local disability legislation
WEEE
In accordance with EN 50419 the GT8 clock must be disposed at the end of its life by returning to a
designated recycling organisation for waste electrical and electronic equipment as dened within the WEEE
directive. The clock must not be disposed of in normal domestic waste.
Batteries should be carefully removed from the clock prior to disposal taking care to prevent short-circuits,
crushing or damage to the battery housing.
Page 8
HardwareSpecication
Display
8 inch full colour capacitive multi-touch display with toughened glass for use in high trac environments
16:10 aspect ratio, 1280 x 800 pixel resolution
A separate glass inlay, below the display, provides the capability to customise the terminal with backlit
corporate branding
Processor
1.6GHz Quad Core
Operating System
Android 10.0
Input / Output
4 + 2 Internal USB 2.0 ports
Facial recognition
A choice of optional input/output accessories are available, including:
Suprema SFM Slim
Lumidigm M320
Expanded ngerprint database of 10,000+ using fast matching on clock algorithm
Contactless smart card readers: Mifare, iClass SE, Feig and Multi-tech readers
Proximity card reader: supports a range of readers, including HID Prox 125kHz
Magnetic stripe card reader
Barcode reader or external scanner: multi-format, Visible and IR
I/O relay modules
Memory
3GB
Internal Persistent Storage
16GB high performance ash storage
Host Connectivity
Ethernet: 10/100/1000MHz
Wi-Fi: Intel dual band, dual stream 802.11ac (optional)
Bluetooth (optional)
Power
12VDC ±5%
Power over Ethernet Plus (POE+) 802.3at
Internal lithium ion battery, up to 2 hours backup
Page 9
HardwareSpecication
Operating Temperature & Humidity
0°C - 35°C (32ºF to 95ºF)
5-90% Non-condensing
Plug and Play Deployment
Fast easy installation
Easy to t reader modules and peripherals
VESA mount xings
Integration
Supports native Android and HTML 5 Apps
Software Development Kit available
Sound
Integrated stereo speakers
Integrated microphone
Camera
5 Megapixel with front illumination; supports photo and video
Physical Security
Metal wall-mount bracket with optional security xing
Optical tamper detection
Dimensions
216mm (H) x 206mm (W) x 78mm (D)
8.5 inches (H) x 8.1 inches (W) x 3.8 inches (D)
Weight: 1.5Kg (3.3Lbs)
Sustainability
7-year design life
Minimal footprint with industry-leading aesthetics
Page 10
HardwareSpecication
Subject Illumination
Visible and IR lighting
Camera
Customisable Inlay
Congurable back lighting
Prox Reader Module
Or custom logo with illumination
Touch Screen
Lumidigm or SF Slim Bio
Module with illumination
Swipe Reader Module
Mag, Barcode Visible & IR
The GT8 Terminal can be customised by tting a range of optional modules.
Reader Modules
125KHz Reader Module RM-HID-B
iClass SE Reader Module RM-ICLSE-B
Elatec MultiTech Reader Module RM-ELATEC-B
Feig HI Reader Module RM-FEIG-HI-B
Feig FC Reader Module RM-FEIG-FC-B
Barcode Visible Red Reader Module RM-BARV-B
Barcode Infra Red Reader Module RM-BAR-B
Magnetic Stripe Reader Module RM-MAG-B
RFIdeas MultiTech Reader Module RM-RFID-B
Tabla de contenidos
