GSM Activate ADRV11 Manual de usuario

GSM AUTO DIALER

Remote monitoring & Control using your mobile phone

www.gsm-activate.co.uk

PAGE 1

MODEL NUMBER - ADRV11

PAGE 2

Product Information

Our GSM Auto-Dialer is a versatile unit which can be attached to many of your

electronic devices in your homes; work, gardens or wherever you may need it.

It will alert you using GSM technology and send you a text message or

make a call to your mobile phone or land line so you are aware if there is a

problem, failure or status change wherever you are in the world.

Our GSM Auto-Dialer is set apart from other models on the market by being

quad band frequency meaning it an be used worldwide and we frequently ship

models all over Europe, USA and Australia with excellent feedback.

The unit is also enclosed in a IP65 rated box which means it is perfectly weathered for

outside installation and has passed testing in high temperature and below

freezing conditions.

Specification

. GSM Frequency: Quad band fre 850/900/1800/1900 Mhz.

· Power Supply Voltage: 9 - 24 volts DC - 1 Amp Max

· Current used in standby mode: 25mA Max

· IP 65 Enclosure rating for outside installation

· 2 inputs: Negative or Positive Triggered

· 10 Amp Relay Output

· Standard 2G Simcard

· No land line required

· Dimensions - L150 x W90 x H45mm

· Dimensions PCB Only - L125 x W67mm

· Sim Active Function

· Input 1: SMS Text Alert Max 3 numbers

· Input 2: Dial Out Call Alert Max 3 numbers

· Operating Temperature: -10...+40°C

· Programmed by Text / SMS Message

· Text for signal strength

INSTRUCTIONS

IMPORTANT - PLEASE READ

PLEASE MAKE SURE YOU DISCONNECT THE POWER WHEN YOU FIT THE SIM

CARD THEN PLACE THE SIM CARD WITH THE CLIPPED CORNER

FACING OUT WARDS. PLEASE SEE PICTURE ABOVE.

SIGNAL STRENGTH:

To help make sure that you place the unit in a suitable position you can text the unit to see

how much signal strength the dialler is receiving, by texting the command #SIGNAL#

The dialler will perform a test on the signal strength.

You will receive a text telling you a signal strength score between 0 up to 30 we strongly

recommend that you place the unit where you can receive a signal strength score of at least

10. You will find that with a score of less than 10 the unit will be unreliable.

You can purchase a 3 metre antenna booster from the website www.gsm-activate.co.uk to

give the unit better signal strength.

1. Slide back the sim door and lift it up.

2. Slide the simcard into the door making sure that the clipped corner of

the simcard lines up with the clipped corner of the simcard holder.

3. Close the sim door.

4. Slide the sim door to lock the simcard in place.

—------------------------------------------------------------------------------

When you first switch the unit on the red and blue led will come on for 3 seconds.

The blue led will then go out leaving just the red led on.

When the unit finds a signal the red led will go out and the blue will come on and

must stay on before you can operate the unit.

PAGE 3

Ho w to p ro g ra m th e c o n ta c t n u mb e r.

After inserting your simcard into the Auto-Dialer turn the unit on and wait until you receive

a steady blue light, this will indicate that you have a mobile signal.

You will now need to send a text with the contact number

Note - To avoid confusion we have colour coded the hash (#) and the equals (=) symbols.

Ex a mp le : (h a s h ) (1 o r 2 o r 3) (e q u a ls ) (p h o n e n u mb e r) (h a s h )

#1=01798865555# then send this as a text to the simcard

#2= 07748434444# then send this as a text to the simcard

#3= 07754063333# then send this as a text to the simcard

If you wish to cancel a number follow this example

Ex a mp le : (h a s h ) (DELETE) (e q u a ls) (1 o r 2 o r 3) (h a s h )

#DELETE=1# then send this as a text to the simcard

PLEASE SEND ONE MESSAGE AT A TIME AND WAIT FOR THE AUTO-DIALER TO SEND

YOU BACK THE TEXT ACKNOWLEDGEMENT

“NUMBER STORED” BEFORE YOU TRY TO ADD ANOTHER NUMBER

Below is a notepad to help you remember the numbers that you have saved to your

simcard in the event you need to modify or delete in the future.

#1=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #

#2= _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #

#3=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #

PAGE 4

How to program the SMS text message

You can now change the alarm message to one of your own choosing.

To change the message send the text command as follows.

#MESSAGE= YOUR MESSAGE #

This will change the message to “YOUR MESSAGE”

The default message is ALARM

PAGE 5

FACTO R Y R ES ET:

To p e r f or m a q u ic k f ac t or y r ese t wh i c h w i l l d el e t e AL L sto red n u mb e r s

an d c u st om m e s sa g es p l ea s e us e t e x t c o m m and #RESET?#

The RED LED will flash 6 times to indicate that the reset has been successful.

How does the Auto-Dialer work?

The Auto-Dialer has two alarm inputs and one 10 amp relay output. When an input is

activated the blue led will start to flash 6x times this indicates that alarm signal has been

triggered.

INPUT 1: (te x t mode ) When activated it will automatically send a text message to 3 pre-

programmed numbers that you have programmed into your Auto-Dialer. The text message

will say (“ALARM”).

INPUT 2: (Ph o n e c a ll mo d e ) When activated it will automatically dial out to 3 pre-

programmed numbers. After dialling the numbers it will hang up after 6 ring tones. This will

prevent any call charges being made to the simcard.

AUTO RESET:

This will happen automatically when the input trigger is reset. The Auto-Dialer will then be

ready for the next trigger input.

*You will receive a text acknowledgement “MESSAGE

STORED” once the unit has changed the message.

NOTE

You can only use a maximum of 30 characters including spaces for your

customised message.

RELAY OUTPUT:

This unit has a 10 amp relay output which can be used to turn on external equipment

such as an alarm bell or lighting. The relay is programmed to come on when the Auto-

Dialer has been triggered for a period of 30 seconds.

Note

Please make sure you have credit on your simcard to receive text messages and

acknowledgments.

Depending on how busy your telephone network is at the time it may take some time to

receive a text acknowledgement.

The unit has a “sim active” function which monitors the activity on the simcard. If it has

been inactive for 6 weeks it sends a text to a pre-recorded number. This will then

eliminate any issues of the simcard getting shut down if they are unused for 3 months.

New SIM cards will need registering before they can be used. Full details of how this is

done can normally be found in the SIM card pack. It will normally require that the SIM

card is inserted into a mobile phone, a number dialled and instructions followed. Details

of how to do this can be found on the SIM card provider’s web site or by calling their

customer services. Please use one of the following SIM card providers (Vodafone,

TMobile, O2 or Orange).

We do not recommend using 3 at this present time

PAGE 6

PAGE 7

Quick Reference

SEND TEXT OPERATION ACKNOWLEDGEMENT

#SIGNAL# Check Signal Strength 0 - 30

#1=number# To Store Number Number Stored

#Delete=1# To Delete Number Number Stored

#MESSAGE=yourmessage# Change Default Message Message Stored

#Reset?# Factory Reset Red Light Flashes X6

Typical Application of Product

● Security alarm system applications

● Supervision and monitoring alarm systems

● Automatic monitoring system

● Vending machines security protection

● Pumping stations; tanks, oil or water levels

● Buildings and real estate

● Weather stations

● River monitoring and flood control

● Fridges/Fish Tanks

● Farming equipment and security

INPUT 1+2

As you can see in the circuit diagram above the inputs are relays and can be activated by

supplying 9v to 24v volts across the input terminals for 4 seconds. This will activate the

input.

Re la y Ou tp u t

The relay has Common, Normally Open and Normally C losed contacts which are

capable of 10 Amp loads. This is suitable for turning on or off electrical equipment.

Alternatively it can be used for resetting your alarm system.

PAGE 8

NOTE - Please make sure you supply a 9 - 24 volts DC from the battery terminals via a 2

amp fuse (for alarm panel installations)

29/05/17 - AD

For more technical support please browse the FAQ’s on our website www.gsm-activate.co.uk

Alternatively email our technical support team at technica[email protected] and we will

do our best to reply within 24 hours Monday - Friday.

Tabla de contenidos

Otros manuales de Sistema de seguridad de GSM Activate

GSM Activate

GSM Activate 2G RF BEAM Manual de usuario

GSM Activate

GSM Activate e-CO Series Manual de usuario

GSM Activate

GSM Activate 3G RF DOOR Manual de usuario

GSM Activate

GSM Activate Alarm Pro 20 Manual de usuario

GSM Activate

GSM Activate ECO Series Manual de usuario

GSM Activate

GSM Activate GSM PT100 Manual de usuario

GSM Activate

GSM Activate 2G RF PIR Manual de usuario

GSM Activate

GSM Activate ECO-BEAM Manual de usuario

GSM Activate

GSM Activate GSM 4G AUTO DIALLER PLUS Manual de usuario

GSM Activate

GSM Activate AD-SD Manual de usuario

GSM Activate

GSM Activate ECO-BEAM Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario