Grundfos CIM 260 Manual de usuario
CIM 260 and CIM 280
Cellular modules
Installation and operating instructions
CIM 260/280
Installation and operating instructions
Other languages
http://net.grundfos.com/qr/i/99440283
GRUNDFOS INSTRUCTIONS
CIM 260 and CIM 280
English (GB)
Installation and operating instructions ..................................4
Deutsch (DE)
Montage- und Betriebsanleitung .....................................15
Dansk (DK)
Monterings- og driftsinstruktion ......................................27
Español (ES)
Instrucciones de instalación y funcionamiento............................38
Suomi (FI)
Asennus- ja käyttöohjeet ..........................................50
Français (FR)
Notice d'installation et de fonctionnement...............................61
Italiano (IT)
Istruzioni di installazione e funzionamento ..............................72
Português (PT)
Instruções de instalação e funcionamento ..............................84
한국어 (KO)
설치 및 작동 지침 ...............................................95
Appendix A..................................................105
EU declaration of conformity .....................................106
UK declaration of conformity.....................................109
3
Table of contents
English (GB) Installation and operating instructions
Original installation and operating instructions
Table of contents
1. General information ............. 4
1.1 Hazard statements .............. 4
1.2 Notes ..................... 4
2. Product introduction ............ 5
2.1 Applications .................. 5
2.2 LEDs ..................... 6
3. Receiving the product............ 7
3.1 Inspecting the product ............ 7
4. Installation requirements .......... 7
4.1 Security .................... 7
4.2 RF safety ................... 8
4.3 Antenna requirements ............ 8
4.4 Radio frequency radiation exposure
information (for Canada and US only) .... 8
4.5 EMC statements for USA ........... 9
5. Mechanical installation ........... 9
5.1 Fitting a cellular antenna ........... 9
5.2 Inserting the SIM card ............10
6. Electrical connection ............10
6.1 Connecting the battery and power supply ..10
6.2 Connecting the battery ............10
6.3 Connecting the power supply.........11
7. Fault finding .................12
7.1 CIM 260 or CIM 280 fitted in a Grundfos
product ....................12
7.2 CIM 260 or 280 fitted in the CIU unit .....13
8. Technical data ................14
9. Disposing of the product ..........14
1. General information
Read this document before you install the
product. Installation and operation must
comply with local regulations and accepted
codes of good practice.
1.1 Hazard statements
The symbols and hazard statements below may
appear in Grundfos installation and operating
instructions, safety instructions and service
instructions.
DANGER
Indicates a hazardous situation which, if
not avoided, will result in death or serious
personal injury.
WARNING
Indicates a hazardous situation which, if
not avoided, could result in death or
serious personal injury.
CAUTION
Indicates a hazardous situation which, if
not avoided, could result in minor or
moderate personal injury.
The hazard statements are structured in the following
way:
SIGNAL WORD
Description of the hazard
Consequence of ignoring the warning
• Action to avoid the hazard.
1.2 Notes
The symbols and notes below may appear in
Grundfos installation and operating instructions,
safety instructions and service instructions.
Observe these instructions for explosion-
proof products.
A blue or grey circle with a white graphical
symbol indicates that an action must be
taken.
A red or grey circle with a diagonal bar,
possibly with a black graphical symbol,
indicates that an action must not be taken
or must be stopped.
If these instructions are not observed, it
may result in malfunction or damage to the
equipment.
Tips and advice that make the work easier.
4
English (GB)
2. Product introduction
2.1 Applications
CIM 260 or CIM 280 cellular module (CIM =
Communication Interface Module) enable data
transmission between a cellular network and a
Grundfos product.
CIM 260 communicates using Modbus TCP via
cellular data transmission to a SCADA system or
SMS communication to mobile phones.
CIM 280 communicates via cellular network to the
related cloud, for example, Grundfos iSolutions
Cloud, (requires a Grundfos contract).
In the following, "Grundfos product" means one or
more Grundfos products, depending on the actual
application.
CIM 260 and CIM 280 cellular module make it
possible to control and monitor a Grundfos product in
several ways:
• From a SCADA system via a data connection.
• From a mobile phone via SMS messages. See the
manual "CIM 260 SMS commands".
• From Grundfos iSolutions Cloud or the related
cloud where control takes place via a central
server. This is not described in this document.
CIM 260 or CIM 280 is supplied separately and must
be fitted in the product to be communicated with or in
a CIU unit (CIU = Communication Interface Unit).
Retrofitting of CIM 260 or CIM 280 is described in the
installation and operating instructions of the Grundfos
product.
If you want CIM 280 to connect to another
cloud than Grundfos iSolutions Cloud, for
example, Grundfos Remote Management,
it can take 3-4 minutes until the interface
reconnects at first communication process.
2.1.1 CIM 260 or CIM 280 cellular module
2
1
3 4 5 7 6
TM084023
CIM 260 or CIM 280 cellular module
5
English (GB)
Pos. Designation Description
1 Battery socket
2 SIM card holder
3Secondary SMA connection for cellular antenna1)
4Primary SMA connection for cellular antenna.
This antenna must always be connected.
5 LED1 Yellow and green status LED for cellular communication.
6 LED2 Red and green status LED for internal communication between CIM 260 or CIM 280
and the Grundfos product.
7 SW1
For CIM 260:
To reset to factory settings, press and hold for at least 5 seconds.
For CIM 280:
To reset CIM 280, press and hold for 1 second.
To reset to factory settings, press and hold for at least 5 seconds.
1) Only use this antenna connection if required by the telecom company.
2.2 LEDs
CIM 260 and CIM 280 cellular module have two
LEDs.
• Yellow and green status LED (LED1) for cellular
communication
• Red and green status LED (LED2) for internal
communication between CIM 260 or CIM 280 and
the Grundfos product.
LED1 (yellow and green)
1
2
3
4
1 second
3 seconds
A B
TM084022
LED1 status
Pos. Description
1 Searching for cellular network
2 Cellular network active
3Data exchanged via data connection2)
4 Sending SMS message
A Yellow
B Green
2) Only applies to CIM 260.
LED1 status
Pos. LED1 status Description for CIM 260 Description for CIM 280
1 Flashing yellow. Searching for a cellular network. Searching for a cellular network.
2 Pulsating yellow (single pulse). Connection to the cellular
network has been established.
Connection to the cellular
network has been established.
3 Pulsating green (single pulse). Data are exchanged via data
connection. -
4 Green (3 sec.). Sending an SMS message. Sending an SMS message.
LED2 status
6
English (GB)
LED2 status Description for CIM 260 Description for CIM 280
Off CIM 260 has been switched off. CIM 280 has been switched off.
Flashing red.
No internal communication
between CIM 260 and the Grundfos
product.
After commissioning, the LED2 will flash red if the
communication to the Grundfos product is lost.
Permanently red. CIM 260 does not support the
Grundfos product.
The product driver is not downloaded from Grundfos
Remote Management (GRM) or Grundfos iSolutions
Cloud (GiC) yet. When the CIM 280 is switched on, the
LED2 may turn green for one minute before it turns
permanently red.
Permanently
green.
Internal communication between
CIM 260 and the Grundfos product
is OK.
Internal communication between CIM 280 and the
Grundfos product is OK.
During startup, it may take up to 5 seconds
to update the LED2 status.
Related information
2.1.1 CIM 260 or CIM 280 cellular module
3. Receiving the product
3.1 Inspecting the product
Before installing the product, do the following:
1. Check that the product is as ordered.
2. Check that no visible parts have been damaged.
3. If parts are damaged or missing, contact your
local Grundfos sales company.
4. Installation requirements
WARNING
Electric shock
Death or serious personal injury
‐Before starting any work on the
product, make sure that the power
supply has been switched off and that
it cannot be accidentally switched on.
‐SELV wires must not come into contact
with other wires with higher voltages.
QR99462331
QR code for the CIU quick guide
4.1 Security
Grundfos connected products must be behind a
firewall or connected to a private network.
If a firewall or private network is not in place, the
Grundfos product may be subject to a cyber-security
risk and becomes vulnerable to an attack or
compromise.
Follow the highly recommended configuration
requirements below. If in doubt, consult an IT
Infrastructure Specialist.
4.1.1 CIM 260, cellular
The CIM 260 modules are cellular-based modules
and require cellular connectivity through a private
Access Point Name (APN) to be securely connected
7
English (GB)
to the Internet. Any basic cellular connectivity solution
is not recommended, only private APNs are
recommended.
The private APN must be purchased from your mobile
network operator. The mobile network operator will
guide you through the setup process.
23
5
41
TM077057
Secure connectivity for CIM 260
Pos. Description
1 Grundfos device
2 Private APN
3 Private mobile network
4 Firewall
5 Internet
4.2 RF safety
Installers and end users must be provided
with these installation and operating
instructions and operating conditions for
satisfying RF exposure compliance.
WARNING
Radiation
Minor or moderate personal injury
‐The antenna used for the product in
which the CIM module is fitted must be
installed to provide a separation
distance of at least 20 cm (0.66 feet)
from persons and must not be co-
located or operated in conjunction with
any other antenna or transmitter.
Interference of other electronic equipment may occur
if the equipment is inadequately protected.
4.3 Antenna requirements
WARNING
Radiation
Death or serious personal injury
‐The combined gain of the cable-
antenna solution used for this product
must not exceed 2.0 dBi (800, 900,
1800, 2100, 2600 MHz).
4.4 Radio frequency radiation exposure
information (for Canada and US only)
This equipment complies with FCC and ISED
radiation exposure limits set forth for an uncontrolled
environment. This equipment must be installed and
operated with a minimum distance of 20 cm (0.66
feet) between the radiator and your body.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
Model: CIM 280-US
TM071660
The host product needs to be labelled
with:
HMN name:______________________
Contains FCC ID: OG3-CIM2X0-3G-4G
Contains IC: 10447A-CIM2X034G.
The enclosed FCC label must be attached near the
barcode label on the product in which the CIM
module is installed. Remember to write the host
marketing name (HMN) on the label according to the
table.
Type on the product
nameplate
HMN name for the FCC
label
MAGNA3 MAGNA3 Z
MLE71 MLE71 Z
MLE80 MLE80 Z
MLE90 MLE90 Z
8
English (GB)
Type on the product
nameplate
HMN name for the FCC
label
MLE100 MLE100 Z
MLE112 MLE112 Z
MLE132 MLE132 Z
MLE160 MLE160 Z
This device complies with Part 15 of the
FCC Rules.
Operation is subject to the following two
conditions:
1. This device may not cause harmful interference,
and
2. This device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications made to this
equipment not expressly approved by
Grundfos may void the FCC authorisation
to operate this equipment.
4.5 EMC statements for USA
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
5. Mechanical installation
5.1 Fitting a cellular antenna
The antenna for CIM 260 or CIM 280 must be
connected to the module to establish connection to
the cellular network.
Connect the antenna cable to the SMA connection
(pos. 1) of CIM 260 or CIM 280. The antenna must be
installed outside the control cabinet in a position with
good reception conditions. If required by the telecom
company, connect an additional antenna.
1
2
TM084024
Fitting an external cellular antenna
Pos. Description
1
Primary SMA connection for the cellular
antenna.
This antenna must always be connected.
2Secondary SMA connection for the cellular
antenna3)
3) Only use this antenna connection if required by the telecom
company.
9
English (GB)
5.2 Inserting the SIM card
Before inserting the SIM card into CIM 260 or CIM
280, remove the PIN code, or set it to "4321".
1. Insert the SIM card into a mobile phone.
2. Remove the PIN code from the SIM card, or set it
to "4321". See the manual of the mobile phone.
3. For CIM 280, you must have a SIM
card subscription with international
SMS roaming activated.
Insert the SIM card into CIM 260 or CIM 280.
The slanted edge of the SIM card must
point downwards.
1
2
TM084025
Inserting the SIM card
Pos. Description
1 SIM card holder
2 SIM card
6. Electrical connection
6.1 Connecting the battery and power
supply
WARNING
Electric shock
Death or serious personal injury
‐Connect CIM only to a Grundfos host
product with a dedicated CIM interface.
‐Installation must be carried out by
qualified and trained experts.
WARNING
Flammable material
Death or serious personal injury
‐The safety precautions listed below
must be observed carefully as
improper handling of the lithium-ion
battery may result in injury or damage
from electrolyte leakage, heating
ignition or explosion.
These safety precautions must be observed:
• Only insert the approved Grundfos battery pack
(99465650).
• Never use this battery pack in other battery
chargers.
• Do not dismantle or modify the battery.
• Do not heat or incinerate the battery.
• Do not pierce, crush or cause mechanical damage
to the battery.
• Do not short circuit the battery.
• Do not allow the battery to get wet or be
immersed in water.
• Do not strike or throw the battery.
• For long periods of storage, the storage
temperature should be below +35 °C.
6.2 Connecting the battery
The CIM 260 and CIM 280 cellular module can be
fitted with a lithium-ion battery, part number
99465650. It is secured by a velcro strap which
absorbs vibrations and makes it easier to replace the
battery. Connect the battery to CIM 260 or CIM 280
as shown below. See the CIU quick guide for
placement of the battery on the CIU cover.
If the battery is not connected, the user will
not receive any information in case of a
power cut.
10
English (GB)
Otros manuales para CIM 260
5
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Unidad de control de Grundfos
Grundfos
Grundfos CIM 150 PROFIBUS DP Manual de usuario
Grundfos
Grundfos PC Tool CU 300 Manual de usuario
Grundfos
Grundfos PM TWIN Manual de usuario
Grundfos
Grundfos CIM 200 Manual de usuario
Grundfos
Grundfos LC 107 Manual de usuario
Grundfos
Grundfos CIM 500 Manual de usuario
Grundfos
Grundfos PM 1 Manual de usuario
Grundfos
Grundfos CIM 290-MA LPWAN GiC Manual de usuario
Grundfos
Grundfos CIM 2 Series Manual de usuario
Grundfos
Grundfos CU 301 Manual de usuario
Grundfos
Grundfos MC 80 Manual de usuario
Grundfos
Grundfos Unilift AP12 Manual de usuario
Grundfos
Grundfos IO 242 Manual de usuario
Grundfos
Grundfos BM Manual de usuario
Grundfos
Grundfos ALPHA1 B Manual de usuario
Grundfos
Grundfos SA-SPM Manual de usuario
Grundfos
Grundfos Vaccuperm VGS -141 Manual de usuario
Grundfos
Grundfos OHJEET CIM 500 Manual de usuario
Grundfos
Grundfos CIM 500 Manual de usuario
Grundfos
Grundfos IO 111 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
