Grundfos CIM 260 Manual de usuario

CIM 260 and CIM 280 cellular modules

Installation and operating instructions

GRUNDFOS INSTRUCTIONS

Installation and operating instructions

Other languages

net.grundfos.com/qr/i/99440283

Table of contents

CIM 260 and CIM 280 cellular modules

(QJOLVK*%

Installation and operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

'HXWVFK'(

Montage- und Betriebsanleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

'DQVN'.

Monterings- og driftsinstruktion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

(VSD³RO(6

Instrucciones de instalación y funcionamiento . . . . . . . . . . . . . . . . . . . . . . . . . 33

6XRPL),

Asennus- ja käyttöohjeet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

)UDQ©DLV)5

Notice d'installation et de fonctionnement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

,WDOLDQR,7

Istruzioni di installazione e funzionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

3RUWXJX¬V37

Instruções de instalação e funcionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Ɋɭɫɫɤɢɣ (RU)

Ɋɭɤɨɜɨɞɫɬɜɨ ɩɨ ɦɨɧɬɚɠɭ ɢɷɤɫɩɥɭɚɬɚɰɢɢ . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

₼㠖&1

Пቯߦ඲ᄊฌ୞෢ 

穢剳檺ͼ΀

昪獞愕沗壟滆獮 

Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

English (GB)

(QJOLVK*%

Installation and operating instructions

Original installation and operating instructions

These installation and operating instructions

describe Grundfos CIM 260 and CIM 280 cellular

modules.

Sections 1-2 give the information necessary to be

able to install and start up the products in a safe way.

Sections 3-6 give important information about

operating the setup, as well as information about

fault finding and disposal of the product.

CONTENTS Page

1. General information

1.1 Hazard statements

The symbols and hazard statements below may

appear in Grundfos installation and operating

instructions, safety instructions and service

instructions.

The hazard statements are structured in the

following way:

1.2 Notes

The symbols and notes below may appear in

Grundfos installation and operating instructions,

safety instructions and service instructions.

1. General information 3

1.1 Hazard statements 3

1.2 Notes 3

2. Installing the product 4

2.1 Security 4

2.2 RF safety 4

2.3 Antenna precautions 4

2.4 Radio frequency radiation exposure

information 4

2.5 Fitting a cellular antenna 5

2.6 Inserting the SIM card 5

2.7 Connecting the battery and power supply 6

3. Product introduction 7

3.1 Applications 7

3.2 LEDs 8

4. Fault finding the product 10

5. Technical data 12

6. Disposal 12

Read this document before installing the

product. Installation and operation must

comply with local regulations and accepted

codes of good practice.

DANGER

Indicates a hazardous situation which, if

not avoided, will result in death or serious

personal injury.

WARNING

Indicates a hazardous situation which, if

not avoided, could result in death or

serious personal injury.

CAUTION

Indicates a hazardous situation which, if

not avoided, could result in minor or

moderate personal injury.

SIGNAL WORD

Description of hazard

Consequence of ignoring the warning.

- Action to avoid the hazard.

Observe these instructions for explosion-

proof products.

A blue or grey circle with a white graphical

symbol indicates that an action must be

taken.

A red or grey circle with a diagonal bar,

possibly with a black graphical symbol,

indicates that an action must not be taken

or must be stopped.

If these instructions are not observed, it

may result in malfunction or damage to the

equipment.

Tips and advice that make the work easier.

English (GB)

2. Installing the product

Fig. 1 QR code for the CIU quick guide

2.1 Security

Grundfos connected products must be behind a

firewall or connected to a private network.

If a firewall or private network is not in place, the

Grundfos product may be subject to a cyber-security

risk and becomes vulnerable to an attack or

compromise.

Follow the highly recommended configuration

requirements below. If in doubt, consult an IT

Infrastructure Specialist.

2.1.1 CIM 260, cellular

The CIM 260 modules are cellular-based modules

and require cellular connectivity through a private

Access Point Name (APN) to be securely connected

to the Internet. Any basic cellular connectivity

solution is not recommended, only private APNs are

recommended.

The private APN must be purchased from your

mobile network operator. The mobile network

operator will guide you through the setup process.

Fig. 2 Secure connectivity for CIM 260

2.2 RF safety

The antenna used for the product in which the CIM

260 or CIM 280 is fitted must be installed to provide

a separation distance of at least 20 cm from persons

and must not be co-located or operated in

conjunction with any other antenna or transmitter.

Interference of other electronic equipment may occur

if the equipment is inadequately protected.

2.3 Antenna precautions

The combined gain of the cable-antenna solution

used for this product must not exceed 2.0 dBi (800,

900, 1800, 2100, 2600 MHz).

2.4 Radio frequency radiation exposure

information

FCC ID: OG3-CIM2X0-3G-4G

IC: 10447A-CIM2X034G

Model: CIM 260-US or CIM 280-US

This equipment complies with FCC and ISED

radiation exposure limits set forth for an uncontrolled

environment. This equipment must be installed and

operated with a minimum distance of 20 cm between

the radiator and your body.

This transmitter must not be co-located or operated

in conjunction with any other antenna or transmitter.

WARNING

Electric shock

Death or serious personal injury

- Before starting any work on the product,

make sure that the power supply has

been switched off and that it cannot be

accidentally switched on.

- SELV wires must not come into contact

with other wires with higher voltages.

TM07 4227 1119

Internet

Firewall

Grundfos

device

Private APN

Private mobile

network

Installers and end users must be provided

with these installation and operating

instructions and operating conditions for

satisfying RF exposure compliance.

The enclosed FCC label must be placed

visibly on the product in which the CIM

module is installed.

The host product needs to be labelled

with:

Contains FCC ID: OG3-CIM2X0-3G-4G

Contains IC: 10447A-CIM2X034G.

TM07 1660 2418

English (GB)

2.5 Fitting a cellular antenna

The antenna for the CIM 260 or CIM 280 must be

connected to the module to establish connection to

the cellular network.

External antenna

See fig. 3.

Connect the antenna cable to the SMA connection

(pos. 1) of the CIM 260 or CIM 280. The antenna

must be installed outside the control cabinet in a

position with good reception conditions. If required

by the telecom company, connect an additional

antenna.

Fig. 3 Fitting an external cellular antenna

* Only use this antenna connection if required by

the telecom company.

2.6 Inserting the SIM card

Before inserting the SIM card into the CIM 260 or

CIM 280, remove the PIN code, or set it to "4321".

Procedure

1. Insert the SIM card into a mobile phone.

2. Remove the PIN code from the SIM card, or set it

to "4321". See the manual of the mobile phone.

3. Insert the SIM card into the CIM 260 or CIM 280.

See fig. 4.

Fig. 4 Inserting the SIM card

This device complies with Part 15 of the

FCC Rules and with RSS-Gen of

Innovation, Science & Economic

Development Canada.

Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference, and

2. This device must accept any

interference received, including

interference that may cause undesired

operation.

Changes or modifications made to this

equipment not expressly approved by

Grundfos may void the FCC authorisation

to operate this equipment.

TM07 1662 2418

Pos. Description

Primary SMA connection for the cellular

antenna.

This antenna must always be connected.

2Secondary SMA connection for the cellular

antenna*

For CIM 280, you must have a SIM card

subscription with international SMS

roaming activated.

The slanted edge of the SIM card must

point downwards. See fig. 4.

TM07 1663 2018

Pos. Description

1 SIM card holder

2 SIM card

English (GB)

2.7 Connecting the battery and power

supply

These safety precautions must be observed:

• Only insert the approved Grundfos battery pack

(99465650).

• Never use this battery pack in other battery

chargers.

•Do not dismantle or modify the battery.

• Do not heat or incinerate the battery.

• Do not pierce, crush or cause mechanical

damage to the battery.

• Do not short circuit the battery.

• Do not allow the battery to get wet or be

immersed in water.

• Do not strike or throw the battery.

• For long periods of storage, the storage

temperature should be below +35 °C.

2.7.1 Connecting the battery

The CIM 260 and CIM 280 cellular module can be

fitted with a lithium-ion battery, part number

99465650. It is secured by a velcro strap which

absorbs vibrations and makes it easier to replace the

battery. Connect the battery to the CIM 260 or CIM

280 as shown in fig. 5. See the CIU quick guide for

placement of the battery on the CIU cover.

Fig. 5 Connecting the battery

2.7.2 Connecting the power supply

Switch on the power supply. The CIM 260 and CIM

280 are powered either by the Grundfos product in

which it is fitted or by the battery in case of a power

cut.

The LED1 is flashing yellow (searching for cellular

network). When the connection to the cellular

network has been established, the LED1 will pulsate

yellow (cellular network active). See fig. 7.

The LED2 is permanently green (internal

communication between the CIM 260 and the

Grundfos product is OK).

The CIM 260 is now ready for initialisation. See the

manual "CIM 260 SMS commands" and for

Dedicated Controls, see the manual with software

descriptions.

When installed from factory, the LED2 on CIM 280 is

permanently red until the product driver is installed.

See section 3.2 LEDs for more information.

WARNING

Electric shock

Death or serious personal injury

- The CIM 260 and CIM 280 must only be

connected to SELV circuits.

WARNING

Flammable material

Death or serious personal injury

- The safety precautions listed below

must be observed carefully as improper

handling of the lithium-ion battery may

result in injury or damage from

electrolyte leakage, heating ignition or

explosion.

If the battery is not connected, the user will

not receive any information in case of a

power cut.

TM07 1664 2418

The battery will only be charged if the

battery temperature is within 0 °C to +45

°C.

English (GB)

3. Product introduction

3.1 Applications

The CIM 260 or CIM 280 cellular module (CIM =

Communication Interface Module) enable data

transmission between a cellular network and a

Grundfos product.

The CIM 260 communicates using Modbus TCP via

cellular data transmission to a SCADA system or

SMS communication to mobile phones.

The CIM 280 communicates via cellular network to

Grundfos iSolution Cloud (requires a Grundfos

contract).

In the following, "Grundfos product" means one or

more Grundfos products, depending on the actual

application.

The CIM 260 and CIM 280 cellular module make it

possible to control and monitor a Grundfos product in

several ways:

• From a SCADA system via a data connection.

• From a SCADA system via a call-up connection.

• From a mobile phone via SMS messages.

See the manual "CIM 260 SMS commands".

• From Grundfos Remote Management or

Grundfos iSolution Cloud (GiC) where control

takes place via a central server. This is not

described in this booklet. See the installation and

operating instructions for Grundfos Remote

Management.

The CIM 260 or CIM 280 is supplied separately and

must be fitted in the product to be communicated

with or in a CIU unit (CIU = Communication Interface

Unit).

Retrofitting of the CIM 260 or CIM 280 is described

in the installation and operating instructions of the

Grundfos product.

3.1.1 CIM 260 or CIM 280 cellular module

Fig. 6 CIM 260 or CIM 280 cellular module

* Only use this antenna connection if required by

the telecom company.

TM07 1661 2018

Pos. Designation Description

1 Battery socket

2 SIM card holder

3Secondary SMA connection

for cellular antenna*

Primary SMA connection for

cellular antenna.

This antenna must always

be connected.

5LED1 Yellow and green status LED

for cellular communication.

6LED2

Red and green status LED

for internal communication

between the CIM 260 or CIM

280 and the Grundfos

product.

7SW1

For CIM 260:

To reset to factory settings,

press and hold for at least 5

seconds.

For CIM 280:

To reset the CIM 280, press

and hold for 1 second.

To reset to factory settings,

press and hold for at least 5

seconds.

23 456

English (GB)

3.2 LEDs

The CIM 260 and CIM 280 cellular module have two

LEDs.

See fig. 1.

• Yellow and green status LED (LED1) for cellular

communication

• Red and green status LED (LED2) for internal

communication between the CIM 260 or CIM 280

and the Grundfos product.

LED1 (yellow and green)

Fig. 7 LED1 status

LED1 status

TM04 2646 2808

Searching for cellular

network

Call-up connection

established*

Data exchanged via

data connection*

Data exchanged via

call-up connection*

Sending SMS

message 1 sec.

3 sec.

Yellow Green

Cellular network active

*Only applies to

CIM 260.

Pos. LED1 status Description for CIM 260 Description for CIM 280

1 Flashing yellow. Searching for a cellular network. Searching for a cellular network.

2Pulsating yellow

(single pulse).

Connection to the cellular network

has been established.

Connection to the cellular network

has been established.

3 Permanently yellow. Call-up connection has been

established. -

4Pulsating green

(single pulse).

Data are exchanged via data

connection. -

5Pulsating green

(double pulse).

Data are exchanged via call-up

connection. -

6 Green (3 sec.). Sending an SMS message. Sending an SMS message.

English (GB)

LED2 status

LED2 status Description for CIM 260 Description for CIM 280

Off The CIM 260 has been switched off. The CIM 280 has been switched off.

Flashing red.

No internal communication between

the CIM 260 and the Grundfos

product.

After commissioning, the LED2 will

flash red if the communication to the

Grundfos product is lost.

Permanently red. The CIM 260 does not support the

Grundfos product.

The product driver is not downloaded

from Grundfos Remote Management

(GRM) or Grundfos iSolution Cloud

(GiC) yet. When the CIM 280 is

switched on, the LED2 may turn

green for one minute before it turns

permanently red.

Permanently green.

Internal communication between the

CIM 260 and the Grundfos product is

OK.

Internal communication between the

CIM 280 and the Grundfos product is

OK.

During startup, it may take up to 5 seconds

to update the LED2 status.

English (GB)

4. Fault finding the product

Faults in a CIM 260 or CIM 280 cellular module can

be detected by observing the status of the two

communication LEDs. See the table below and

section 3.2 LEDs.

CIM 260 or CIM 280 fitted in a Grundfos product

DANGER

Electric shock

Death or serious personal injury

- Before starting any work on the product,

make sure that the power supply has

been switched off and that it cannot be

accidentally switched on.

Fault (LED status) Possible cause Remedy

1. Both LEDs (LED1 and LED2)

remain off when the power

supply is connected.

a) The CIM module is fitted

incorrectly in the Grundfos

product.

Check that the CIM module is

fitted correctly in the Grundfos

product.

b) The CIM module is defective. Replace the CIM module.

2. The LED for internal

communication (LED2) is

flashing red.

a) No internal communication

between the CIM module and

the Grundfos product.

Check that the CIM module is

fitted correctly in the Grundfos

product.

3. The LED for internal

communication (LED2) is

permanently red.

a) The CIM module does not

support the Grundfos product.

Contact the nearest Grundfos

company.

b) The CIM 280 is not

configured. The product driver

is not downloaded from

Grundfos Remote

Management (GRM) or

Grundfos iSolution Cloud

(GiC) yet. When the CIM 280

is switched on, the LED2 may

turn green for one minute

before it turns permanently

red.

Run the set-up process in GRM or

GiC. Contact the nearest Grundfos

company.

4. LED1 is flashing yellow. a) The SIM card has not been

inserted.

Insert the SIM card. See section

2.6 Inserting the SIM card.

b) The SIM card has not been

inserted correctly.

Insert the SIM card. See section

2.6 Inserting the SIM card.

c) The PIN code of the SIM card

has not been removed or set

to 4321.

Remove the PIN code, or set it to

4321 with a mobile phone. See

section 2.6 Inserting the SIM card.

d) No connection to the cellular

network.

•Check the connection to the

antenna.

•Check the cellular coverage of

the area with for instance a

mobile phone.

• Experiment with the position of

the external antenna.

• In some cases, adding an

additional antenna to the

second SMA connector may

improve the signal. See fig. 3.

5. LED1 is pulsating yellow with

single pulse, but the CIM 260

cannot send or receive SMS

messages.

a) The CIM 260 has not been

initialised.

Initialise the CIM 260 with the

command INIT. See section

2.6 Inserting the SIM card in the

manual "CIM 260 SMS

commands".

Otros manuales para CIM 260

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unidad de control de Grundfos

Grundfos

Grundfos CIM 500 Ethernet for PROFINET IO Manual de usuario

Grundfos

Grundfos DID Series Manual de usuario

Grundfos

Grundfos CIM 500 Manual de usuario

Grundfos

Grundfos CIM 500 Manual de usuario

Grundfos

Grundfos CIM 500 Manual de usuario

Grundfos

Grundfos CU 242 Manual de usuario

Grundfos

Grundfos CU 100 Manual de usuario

Grundfos

Grundfos IO 112 Manual de usuario

Grundfos

Grundfos CIM 260 Manual de usuario

Grundfos

Grundfos MFV Manual de usuario

Grundfos

Grundfos UP-ZV Series Guía de inicio rápido

Grundfos

Grundfos CMB-SP Booster PM2 Manual de usuario

Grundfos

Grundfos PC Tool CU 300 Manual de usuario

Grundfos

Grundfos MP 204 Manual de usuario

Grundfos

Grundfos G 401 Manual de usuario

Grundfos

Grundfos MFV Manual de usuario

Grundfos

Grundfos MAGNA 2000 Series Manual de usuario

Grundfos

Grundfos MP 204 Manual de usuario

Grundfos

Grundfos KJ1 GU02 Manual de usuario

Grundfos

Grundfos CIM 200 Manual de usuario

Grundfos

Grundfos MP 204 Manual de usuario

Grundfos

Grundfos COMFORT PM Series Manual de usuario

Grundfos

Grundfos Vaccuperm VGS -141 Manual de usuario

Grundfos

Grundfos MC 40/60 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario