Greystone Energy Systems NDD Series Manual de usuario

NDD Series - NO2 Transmitter Installation Manual

Feb 2, 2016 NDD-INS-002 Page 1

Introduction

The NO2 Transmitter uses an electrochemical sensor to monitor the NO2

level and outputs a 4-20 mA signal. It features a 3-wire analog output and

an alarm relay .

Before Installation

Read these instructions carefully before installing and commissioning the

NO2 transmitter. Failure to follow these instructions may result in product

damage. Do not use in an explosive or hazardous environment, with

combustible or flammable gases, as a safety or emergency stop device or

in any other application where failure of the product could result in

personal injury. Take electrostatic discharge precautions during

installation and do not exceed the device ratings.

Operation

In normal operation the sensor will measure the NO2 level in the surrounding air and output a proportional value on the 4-20

mA output. The NO2 measurement range is 0 to 10 ppm. The relay can be used to indicate an alarm condition. The trip point

for the relay can be programmed to three different settings with an on-board jumper. If the NO2 level exceeds the trip point

then the relay is activated. The relay will remain activated until the NO2 level drops below the (trip level – hysteresis) where

hysteresis is 3%.

Start-up

Verify that the NO2 Transmitter is properly wired according to the wiring diagrams and all connections are tight. Apply

power to the device and the sensor will begin reading the NO2 level and output the analog signal.

Mounting

The NO2 enclosure should be mounted on a flat surface three to five feet from the floor of the area to be controlled. Do not

mount the sensor near doors, opening windows, supply air diffusers or other known air disturbances. Avoid areas with

vibrations or rapid temperature changes.

NDD Series - NO2 Transmitter Installation Manual

Feb 2, 2016 NDD-INS-002 Page 2

Wiring

Use 22 AWG shielded wire for all connections and do not locate the device wires in the same conduit with wiring used to

supply inductive loads such as motors. Disconnect the power supply before making any connections to prevent electrical

shock or equipment damage. Make all connections in accordance with national and local codes.

The product is a 3-wire sourcing. Follow the example wiring diagrams to determine the correct wiring for the product. All

models have the same terminal functions.

Connect either an AC or DC power supply to POWER and COMMON and the 4-20 mA signal is available on the

OUTPUT terminal with respect to COMMON. The current output operates in the Active mode and does not require a loop

power supply. This means the signal current is generated by the transmitter and must not be connected to a powered

input or device damage will result. This is the typical operating mode of a “three-wire device”. Check the controller Analog

Input to determine the proper connection before applying power.

Ensure the controller Analog Input (AI) matches the transmitter output signal type before power is applied. The current signal

has a maximum load that it will drive. Follow the ratings in the Specification section or inaccurate readings may result.

The relay output is available on the NO, NC and R.COM terminals. The relay R.COM terminal is NOT connected to the

signal or power supply COMMON terminal. The relay output is completely isolated and has both Normally Open (NO) and

Normally Closed (NC) signals. These signals can be used to directly control alarms, ventilation fans or may be connected to

digital inputs of the B.A.S. for status monitoring.

NDD Series - NO2 Transmitter Installation Manual

Feb 2, 2016 NDD-INS-002 Page 3

Calibration

The transmitter features a simple snap-mount sensor pcb that is pre-calibrated. This means that the entire sensor pcb can

simply be replaced with a new calibrated pcb if desired without having to remove the enclosure. This sensor swap requires no

tools and can be completed in seconds. Simply disconnect the device wiring, remove the old sensor pcb, snap in the new pcb

and reconnect the device power. There is no need to make any adjustments or apply gas to the transmitter using the sensor

swap method.

The device may also be calibrated or verified with NO2 gas if required. This requires a field calibration kit consisting of Zero

and Span of gases, Calibration adapter, Tubing with a calibration cap to cover to the sensor, a miniature screwdriver and a

digital multi-meter.

Verification can be done without removing the device cover. Simply apply Span gas using the calibration cap attached

directly to the port on the cover and monitor the output signal.

The device cover must be removed to perform an actual calibration. In this case, the gas calibration cap attaches to the sensor

fixture inside the enclosure. The sensor must be continuously powered for at least 1/2 hour prior to calibration. Calibrate the

sensor either in clean air or by applying Zero gas with a flow rate of 0.5 to 1 liters per minute. Wait 2 minutes and adjust the

ZERO pot on the sensor board until a 4 mA output is obtained.

Then attach the Span gas supply. Attach the cap to the fixture over the sensor. Slowly turn the valve knob on the regulator to

let the gas begin flowing. Calibrate the sensor either by applying Span gas with a flow rate of 0.5 to 1 liters per minute. Wait

2 minutes and adjust the Span pot on the sensor board until a 20 mA output is obtained. The Span gas need not be the full

scale concentration, but could be a fraction of this. A half scaled concentration, accordingly, should provide a 12 mA signal.

If the gas cap is too loose on the fixtures, simply place a wrap of electrical tape around the cap to tighten it up.

Verify With Cover In Place Calibrate With Cover Removed

NDD Series - NO2 Transmitter Installation Manual

Feb 2, 2016 NDD-INS-002 Page 4

Common Specifications

Measurement . . . . . . . . . . . . . . . . . Electrochemical

Sample Method . . . . . . . . . . . . . . . Diffusion

Measurement Range . . . . . . . . . . . 0-10 ppm

Accuracy . . . . . . . . . . . . . . . . . . . . 0.2 ppm or 5% of reading (whichever is greater)

Sensor Life Expectancy . . . . . . . . . > 2 years

Operating Temperature . . . . . . . . . -20-50 C (-4 -122 F),

Operating Humidity . . . . . . . . . . . . 15-90 %RH (0-99% intermittent)

Pressure . . . . . . . . . . . . . . . . . . . . . Atmospheric 10%

Typical Area Coverage . . . . . . . . . 700 m2(7500 ft2) or 15 m (50 ft) radius

Calibration Adjustments . . . . . . . . Zero and Span pots

Wiring Connections . . . . . . . . . . . Screw terminal block (14 to 22 AWG)

Enclosure . . . . . . . . . . . . . . . . . . . 2.8”w x 4.1”h x 1.9”d (71 x 104 x 48 mm)

Power Supply . . . . . . . . . . . . . . . . 24 Vdc ± 20% or 24 Vac ± 10% (non-isolated half-wave rectified)

Consumption . . . . . . . . . . . . . . . . . 50 mA max

Output Signal . . . . . . . . . . . . . . . . 4-20 mA sourcing

Output Drive Capability . . . . . . . . 550 ohms max @ 24 Vac/dc

Relay Contacts . . . . . . . . . . . . . . . SPDT, Form C contacts (N.O. and N.C.), 5 Amps @ 30 Vdc

Relay Trip Point . . . . . . . . . . . . . . Low = 1 ppm, Mid = 3 ppm or High = 5 ppm, jumper selectable

Relay Hysteresis . . . . . . . . . . . . . . 3%

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de Greystone Energy Systems

Greystone Energy Systems

Greystone Energy Systems TE500AD Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems CDD3B1 Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems CMD5B1000 Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems PS-2ADP Series Manual

Greystone Energy Systems

Greystone Energy Systems HRC Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems TE500AS Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems PMRMC Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems CD2DT Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems RH100B Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems HAHRC Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems CMD5B1 010 Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems CDD4A1 Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems TDAP Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems CD2RMC Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems CDD4B1 Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems HATXFL Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems HSOB Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems HATXOB Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems AVDT Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems CDD4 Manual de usuario

Greystone Energy Systems

Greystone Energy Systems ELP-S Manual de usuario

Greystone Energy Systems

Greystone Energy Systems GDT Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems CDD3A1 Series Manual de usuario

Greystone Energy Systems

Greystone Energy Systems HATXSO Series Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario