To set te porary override progra te perature:
his function allows you to temporarily override the C
temperature from the E temperature settings, until next C
setting (or vice versa).
Program temperature setting until next E setting.
he unit is running at C program period. Press to change from
C to E setting (until the next C program period).
he unit is running at E program hour. Press to change from
E to C setting (until next E program hour).
To set vacation or per anent override Te perature:
his function allows you to set your vacation temperature from
1to 99 days or to set a permanent override temperature forever.
Press key the two bars “ ” will flash under “SA SU” Press
or key to select the number of days for your vacation period.
he maximum selection is up to 99 days. If you choose the
period will be permanent override. Press key to confirm the
vacation period.
Press or key to select temperature. Press key to confirm
the override setting.
To cancel anual, te porary, vacation or per anent
override:
Press or key to return into running mode. Or press key to
turn off the unit.
To switch the unit ON and OFF:
Press key to turn off from on. Press key to turn on from off.
To reset the unit:
Press the Reset key to reset the unit into initial clock setting mode.
All previous programs will reset to factory preset settings.
Sensor:
his thermostat ( HP1-C) uses the most advance temperature
sensing element located on the lower right side of the cast under
the grill. If the sensor is touched accidentally you must allow few
minutes for sensor to come back to normal temperature.
he temperature is measured every minute.
WES ROAD, HARLOW
ESSEX, CM20 2BG, UK
www.greenbrook.co.uk
Issue no: 702034
Mode Air-conditioning Heating
23oc 20oc
28oc 17oc
DIP SWI CH 1 - SWING CYCLE - ON = 0.2OC
OFF = 0.5OC
DIP SWI CH 2 - HEA ING OR AIR-CONDI IONING
System setting
ON = AIR CONDI IONING
OFF = HEA ING
I portant
Note: Do not set the beginning and end of the program to 0:00
due to the thermostat needing this time for its reference use.
Therefore you must set the beginning or end time at 23:00 or
01:00.
To view and change or te perature:
he C and E temperature is preset to the temperatures in the
below table for heating and air-conditioning mode:
Press key to view C and E temperature mode.
Press to change the viewing of C setting from E setting
or press key to change the viewing of E setting from C
setting. he temperature is flashing at this moment. Press or
key to change C or E setting. Press key to confirm the
setting and return to running mode.
To set te porary anual override te perature:
his function allows you to change the present temperature
setting to a temporary temperature setting from next 1hour up
to 48 hours. Press or to enter the manual override
temperature mode and temperature is flashing.
Press or key to select override temperature. Press key
to confirm temperature setting.
H1will be flashing.
Press or key to select hours for overriding time.
he maximum hours are 48. Press key to confirm setting.
Note: he first hour of override (H1) will only run for maximum
45 minutes. However from the second hour onwards will run
for full hour timing. e.g. If you select 2hours override the
maximum time of override will be 1hour and 45 minutes.
Press key. he Monday preset program at 0.00 is on display.
Press or key the display will show the temperature setting
in each hour. e.g. Monday program show 0:00 -5:59 and 8:00 -
15:59 are set at Economy temp.,6:00 -7:59 and 16:00 -22:59 is
set at C (Comfort temp). Note 23:00 -0:00 is set at E
(Economy temp).
Press key the next day preset program is displayed. Again
Press or key. his will show the temperature setting at each
hour. Repeat above steps, each preset program will display until
Sunday. Once Sunday program has been reviewed. Press key.
he display will return into running mode.
To change preset progra :
he preset program may not be suitable for some families but
the program may be adjusted to suit your living life style.
he following instructions will allow you to change the preset
program.
Press key to enter into program viewing mode.
Press key to select the day of program to make a change.
Press or key to select the hour to make change. Press or
to select the temperature to make change. e.g. o change
Saturday 12:00 -16:59 from C to 12:00 -16:59 E .
1. Press key to enter into program viewing mode.
2. Press key to select the day to Saturday program.
3. Press key until 12:00 with C setting.
4. Press key to change C period to E period.
5. Repeat step 3&4to change 13:00 -14:00 from C period to
E period.
6. Press key to confirm setting. Press key to return into
running mode.
TECHNICAL DATA
Temperature range: 5-30oC
Differential: +/- 0.5oC from set temperature.
Temperature accuracy: +/- 0.5oC
Batteries: 2x AA (1.5VDC) size batteries
Receiver Rated switching 230V, 50Hz AC resistive load,
power: 5A Inductive load
Minimum on time in
heating mode: 1minute
Minimum off time in
air-conditioning mode: 3minutes
RF Frequency: 433MHz
User Optional Selection:
Lever off the the back panel to reaveal the circuit board, the DIP
SWI CH is where the user can select following option:
Fig 4.2
