GReddy 12529003 Manual de usuario
Instruction Manual P/N: 12529003
Make: Nissan Model: 370z Year: 2009-2012 Engine: V6-3.7L
Label Qty. Description Part Number
A 1 Air Filter (Pro DRY S) 61-90127
B 1 Tube #1 Passenger side 05-T3017P1
C 1 Tube #2 Driver’s side 05-T3017P2
D 2 Tube #3 05-T3017P3
E 2 Coupling: Elbow 2-3/4” ID x 45 Deg 05-01190
F 2 Coupling: Straight 2-3/4” ID x 1-3/4”L 05-01107
G 8 Clamp, 044 03-50019
H 2 Hose, 5/8” (2 inches) 05-00069
I 4 Screw, M4 x .7 x 8 03-50034
J 4 Screw, Hex Hd: M6 x 1 x 12 03-50032
K 1 Nut, Hex: M6 x 1 03-50059
L 5 Washer, Flat: 1/4” 03-50043
Installation will require the following tools:
Phillips screw driver, 10mm socket, Extention, Ratchet, Pliers & 5/16 nut driver.
Note: Legal in California for use on race vehicles only. The use of this device on vehicles used on public
streets or highways is strictly prohibited in California and others states that have adopted California
emission regulations.
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 949-588-8300.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Disconnect the negative battery terminal before proceeding.
• Retain factory parts for future use.
Page 2
Label Qty. Description Part Number
A 1 Air Filter (Pro DRY S) 61-90127
B 1 Tube #1 Passenger side 05-T3017P1
C 1 Tube #2 Driver’s side 05-T3017P2
D 2 Tube #3 05-T3017P3
E 2 Coupling: Elbow 2-3/4” ID x 45 Deg 05-01190
F 2 Coupling: Straight 2-3/4” ID x 1-3/4”L 05-01107
G 8 Clamp, 044 03-50019
H 2 Hose, 5/8” (2 inches) 05-00069
I 4 Screw, M4 x .7 x 8 03-50034
J 4 Screw, Hex Hd: M6 x 1 x 12 03-50032
K 1 Nut, Hex: M6 x 1 03-50059
L 5 Washer, Flat: 1/4” 03-50043
GReddy.com
D
C
E
F
Page 3
H
J
A
B
D
E
F
G
G
GG
H
II
J
K
L
L
L
Refer to Figure A for step 1-2
Step 1: Begin removing the engine strut brace by removing the two nuts and one bolt from both the
passenger and driverside strut towers 1 .
Step 2: Remove the plastic cover located under the windshield wipers 2 and remove the two nuts
securing the strut brace to the vehicle, then remove the strut brace.
REMOVAL
Page 4
1
2
1
Figure A
Refer to Figure B for steps 3-6
Step 3: Remove the five mounting nuts from the engine cover and lift the cover out of the vehicle 3 .
Step 4: Disconnect the crank case ventilation from the intake tubes 4 .
Step 5: Disconnect both intake tubes from the throttle bodies by loosening the clamps 5 .
Step 6: Unplug the mass air flow sensor harnesses from the intake tubes and disconnect the plastic
retainer clips securing the wire harness to the air boxs 6 .
REMOVAL
GReddy.com
Page 5
3
4
3
33
4
3
5
5
6
6
66
Figure B
Refer to Figure C for steps 7-8
Step 7: Loosen and remove the air box mounting bolts from both the passenger and driverside 7
air box.
Step 8: Remove the complete air box and intake tubes out of the vehicle.
Figure C
REMOVAL
Page 6
7
Refer to Figure D for steps 9-12
Step 9: Remove the 7 (white circles) retaining clips from the splash guard and remove it.
Step 10: Remove the 7 (black circles) retaining clips from the bumper.
Step 11: Remove the two 10mm bolts that connect the bumper to the fenders.
Step 12: Remove the bolts that are located underneath the car that connects the bumper to the belly
pan then carefully remove bumper from vehicle.
Figure D
REMOVAL
GReddy.com
Page 7
Page 8
Page left blank intentionally
Refer to Figure E for step 13-14
Step 13: Insert both supplied silicone couplings through the radiator support passage 8 .
Step 14: Remove the three factory screws for the bumper support brace and replace with the supplied
hex head screws and washers 9 .
Figure E
INSTALL
Page
88
999
Page 9
L
J
Page left blank intentionally
GReddy.com
Refer to Figure F for steps 15-19
Step 15: Place the supplied straight couplings onto the throttle bodies with the clamps provided 10 .
Step 16: Install a clamp on each side of the elbow couplings going through the radiator support.
Step 17: Install the supplied crank case vent hoses on factory crank case chambers 11 .
Step 18: Remove both mass air flow sensors & gaskets from your factory intake tubes and install them
carefully onto your new upper intake tubes with the screws provided. (Do not mix up sensors)
Step 19: Install both upper intake tubes into position and attach the crank case vent hoses 12 .
Figure F
INSTALL
Page
10 10
11 11
12 12
Page 10
Page left blank intentionally
Refer to Figure G for step 20-25
Step 20: Position the lower intake tubes into the elbow couplings 13 .
Step 21: Guide the intake tubes into the supplied air filter and adjust the intake tubes to line up with the
air filters mount 14 and tighten with the supplied hardware.
Step 22: Tighten all clamps and connections then plug in the mass air flow sensors harnesses.
Step 23: Re-install bumper in reverse order.
Step 24: Re-install engine cover and strut brace in reverse order.
Step 25: Verify all connections are secure, your installation is now complete.
Figure G
INSTALL
13 13
14
Otros manuales de Accesorios para automóviles de GReddy
GReddy
GReddy Intercooler Kit Manual de usuario
GReddy
GReddy 12559101 Manual de usuario
GReddy
GReddy AERO KIT Manual de usuario
GReddy
GReddy Type-RS BRS-HGC20 Manual de usuario
GReddy
GReddy BRS-503 Manual de usuario
GReddy
GReddy Turbo Kit Manual de usuario
GReddy
GReddy Profec Manual de usuario
GReddy
GReddy Turbo Kit Manual de usuario
GReddy
GReddy Supercharger Kit Manual de usuario
GReddy
GReddy TYPE-RS BRS-313 CT9A Manual de usuario
GReddy
GReddy 12569001 Manual de usuario
GReddy
GReddy TYPE-RS BRS-112 JZA80 Manual de usuario
GReddy
GReddy 12519101 Manual de usuario
GReddy
GReddy TYPE-RS BRS-307 D32 Manual de usuario
GReddy
GReddy Turbo Kit Manual de usuario
GReddy
GReddy Turbo Kit Manual de usuario
GReddy
GReddy Turbo Kit Emanage Ultimate Manual de usuario
GReddy
GReddy Turbo Kit Manual de usuario
GReddy
GReddy SW-20 Manual de usuario
GReddy
GReddy e-manage ultimate Manual de usuario
