GRAPHTEC JS500 Manual de usuario
JS500
INKJET PRINTER
USER’S MANUAL
MANUAL NO. JS500-UM-151
i
To Ensure Safe and Correct Use
· To ensure the safe and correct use of your printer, read this manual thoroughly prior to use.
· After reading this manual, store it in a safe place for reference as necessary.
· Do not allow small children to touch the printer.
· The following describes important points for safe operation. Be sure to observe them strictly.
Conventions Used in This Manual
To ensure the safe and correct use of the printer as well as to prevent human injury and property damage, the
safety precautions provided in this manual are ranked in the three categories described below. Be sure to gain
a full understanding of the difference between each of the categories before reading the Manual.
This category provides information that, if ignored, is highly likely to cause fatal or
serious injury to the operator.
This category provides information that, if ignored, is likely to cause fatal or serious
injury to the operator.
This category provides information that, if ignored, could cause injury to the operator
or damage to the printer.
Description of Safety Symbols
The symbol indicates information that requires careful attention (including
warnings). The specic point requiring attention is described by an illustration or
text within or next to the symbol.
The symbol indicates an action that is prohibited. Such prohibited action is
described by an illustration or text within or next to the symbol.
The symbol indicates an action that must be performed. Such imperative action
is described by an illustration or text within or next to the symbol.
DANGER
WARNING
CAUTION
ii
Safety Precautions
To ensure the safe and correct use of your printer, be sure to observe the following points.
■ Installation Precautions
WARNING
Do not install the printer in the vicinity of volatile solvents such as
alcohol or thinner.
● A volatile solvent coming into contact with any of the internal electrical
components may result in a re hazard or electric shock.
Do not place objects such as those listed below on top of the printer.
● Objects such as these coming into contact with any of the internal electrical
components may result in a re hazard or electric shock.
• Metallic objects such as necklaces
• Objects such as glasses, vases, houseplants, etc. that contain water or
other uids.
If any of these objects does come into contact with the internal electrical
components immediately turn off the power, remove the plug from the power
outlet, and either contact the store where you purchased your printer or your
nearest Graphtec representative.
CAUTION
Do not use the printer in an unstable location such as on a slope or
a location that is subject to a lot of vibration.
● Such locations may cause the printer to tip over and cause injuries.
Do not place heavy objects on top of the printer.
● Such objects may tip over or fall off, causing injuries.
If the printer is mounted on its dedicated stand, be sure to use the
caster stoppers to x the stand in place and prevent it from moving
while the printer is being used.
● If the stand is not xed in place, the printer may tip over and cause injuries.
Prohibited
Shock hazard
Don’t use
around water
Prohibited
Prohibited
Prohibited
iii
Avoid using the printer in the following locations.
● Use in such locations may result in a re hazard or electric shock.
• Excessively humid or dusty locations
• Locations exposed to direct sunlight
• Locations exposed to high temperatures
• Locations near ames or moisture
● Use at the following places may result in malfunction or failure.
• Near equipment which generate a strong magnetic force or magnetic eld.
● Use this printer in places where the ambient temperature is between 20 to 28°C
centigrade and humidity is between 40 to 70% (non-condensing).
Leave plenty of space around the printer.
● Leave sufcient space for operations in front of and behind the printer.
Prohibited
Approx. 3 m
(front side)
Approx. 2 mApprox. 2 m
Approx. 3 m
iv
Be careful of the following when connecting a ground wire.
● [Items which allow connection to a ground wire]
• Ground terminals of electric outlets
• Ground terminals after completion of grounding work (type D)
● [Items which do not allow connection to a ground wire]
• Water pipes
Water pipes may have plastic parts in the middle which do not serve as grounding.
It is possible to connect a ground wire to water pipes which are approved by the waterworks department to
use for grounding.
• Gas pipes
They may cause explosions or res.
• Ground terminals for telephone lines and lightning conductors
These may get a high-voltage current from lightning which may cause res or electric shocks.
■ Power Supply Precautions
WARNING
Do not damage the power cable, or modify it in any way. Moreover,
do not place heavy objects on the power cable, pull on the cable, or
bend it excessively.
● There may be current leakage from the damaged parts, resulting in a re
hazard or electric shock.
● Do not unplug or plug in the power cable when your hands are wet, such
action may result in electric shock.
Do not connect multiple devices to the same power outlet.
● Use of the printer in such a condition may result in a re hazard or electric
shock.
Do not bundle or tie-wrap the power cable.
● Use of a bundled power cable may result in a re hazard or electric shock.
Make sure that the power cable is rmly inserted into the power
outlet.
● Use of a power cable when the plug is not completely inserted into the power
outlet may result in a re hazard or electric shock.
Do not use a power cable other than the one supplied with your
printer.
● Use of a different power cable may result in a re hazard or electric shock.
Prohibited
Prohibited
Prohibited
Prohibited
v
CAUTION
The rated voltage for this printer is AC 200 - 240 V. Use an appropri-
ate power source and voltage for the specications of this printer.
●
Using this printer with a power source and voltage which are not compatible
with the specications may result in a re or an electric shock.
●
The operating conditions of this printer are as follows. Use a power source
which meets these conditions.
Power source and voltage: AC 200 - 240 V
Power supply frequency: 50/60Hz
When disconnecting the power cable, be sure to hold on to the plug,
and not pull on the cable itself.
●
Pulling on the cable will expose the core wires, or cause damage such as
broken wires. Current leakage from the exposed or damaged areas may result
in a re hazard or electric shock.
As a general rule, do not use an extension cord.
●
Use of an extension cord may result in a re hazard or electric shock. If you
must use an extension cord, unbundle it, and make sure that the power plug is
rmly inserted into the extension cord socket.
Make sure that the power plug can be readily unplugged at any time,
and that there are no objects placed in its vicinity.
● Objects placed in the vicinity of the power plug will prevent its removal in an
emergency.
Be sure to ground the earth terminal.
●
Electric leaks which occur when no grounding wire is connected may lead to
res or electric shocks.
●
Be sure to have a ground connection.
●
Be sure to have a ground connection before connecting a power plug to a
power source. Be sure to remove a ground connection after disconnecting a
power plug from a power source.
Grounding
wire required
vi
■ Handling Precautions
WARNING
Do not disassemble or modify the printer.
●
Such actions may result in a re hazard or electric shock.
If the printer makes an unusual noise, generates smoke, overheats,
emits a strange odor, or otherwise functions abnormally,
immediately turn off the power, remove the plug from the power
outlet, and either contact the store where you purchased your
printer or your nearest Graphtec representative.
●
Use of the printer in such a condition may result in a re hazard or electric
shock.
Do not use ammable aerosols or similar products in the vicinity of
the printer.
●
The gas contained in the spray may cause a re hazard or electric shock if it
comes into contact with the printer's internal electrical components.
Before moving the printer, make sure that the power switch is in the
"off" position and that the power plug has been removed from the
power outlet.
●
If the printer is moved while it is still plugged into the power outlet, he power
cable may be damaged and cause a re hazard or electric shock.
Disassembly
prohibited
Prohibited
vii
CAUTION
Take care not to drop metallic items such as paper clips or staples,
or spill water, other uids or ammable solvents (alcohol, benzene,
thinner, etc.) inside the printer.
●
Metallic items or uids coming into contact with the internal electrical
components may result in a re hazard or electric shock. If such items or uids
fall or are spilled inside the printer, immediately turn off the power, remove
the power plug from the power outlet and either contact the store where you
purchased the printer or your nearest Graphtec representative.
Do not insert your hands inside the printer during a printing
operation or when paper is being loaded.
●
Moving parts inside the printer may cause injuries.
Prohibited
Appropriately connect interface cable.
●
Connecting cables in the wrong direction may result in failure.
viii
■ Maintenance and Inspection Precautions
WARNING
Be sure to turn off the power and remove the power plug from the
power outlet before performing any cleaning operations.
●
Failure to do so may result in a re hazard or electric shock. Moreover, there
is a risk of injury if the printer starts to move during a cleaning operation.
To clean the printer, use a cloth that has been dampened with
neutral detergent and then well wrung out. Do not use volatile
solvents such as alcohol, benzene or thinner to clean the printer.
●
A volatile solvent coming into contact with any of the internal electrical
components may result in a re hazard or electric shock.
CAUTION
At least once a year, remove the power plug from the power outlet and clean the prongs and
surrounding areas.
●
A build-up of dust may result in a re hazard.
Do not apply any lubricant to mechanical sections of this printer.
●
This may deteriorate the performance of this printer which may lead to
malfunction or failure.
●
Subsequent short circuits or heat generation may result in a re or an electric
shock.
When cleaning or checking the inside of the printer, make sure that a metallic object such as
a necklace or bracelet does not come into contact with any of the internal components.
●
Such actions may result in injuries or an electric shock.
When replacing roll paper, loading paper, or removing paper that has become jammed in the
printer, take care not to cut yourself on the edges of the paper.
●
Sharp paper edges may cause injuries.
Prohibited
Prohibited
When removing paper that is jammed inside the printer, take care not to get ink from the
paper on your clothing or hands.
●
Ink may adhere to your clothing or hands.
Otros manuales para JS500
1
Tabla de contenidos
Otros manuales de Impresora de GRAPHTEC
GRAPHTEC
GRAPHTEC JS500 Manual de usuario
GRAPHTEC
GRAPHTEC JW220-06 Manual de usuario
GRAPHTEC
GRAPHTEC SignJet JS310 Series Manual de usuario
GRAPHTEC
GRAPHTEC DP-581H Manual de lista de piezas
GRAPHTEC
GRAPHTEC SignJet JS310-25ES Manual de usuario
GRAPHTEC
GRAPHTEC Craft ROBO CC100-20 Manual de usuario
GRAPHTEC
GRAPHTEC SignJet JS310 Series Manual de instalación y operación
