GRAPHTEC FC8000 Series Manual de usuario

GRAPHTEC FC8000

CONTROL PANEL SETTINGS

IMPORTANT-If you are going to reset to factory defaults, make sure the operator has a list of CONDITIONS

settings [force, speed] written down for the different conditions they have been using so they can re-enter the

values. Also record Sensor Offset Values if they have previously been established.

RESET TO FACTORY DEFAULTS:

FC8000 series:

1. Power off the cutter

2. Press and hold UP arrow key while power back on

3. Release Up key, choose 1 Default Setting

4. Press 1 Set Default

5. Press 1 Continue

6. Press 3 Command

7. If using Flexisign, Photoprint or Wasatch choose HP-GL, if using Cutting Master choose

GP-GL, press ENTER to confirm.

8. Power off, a few seconds later power on to continue use

CONTROL PANEL SETUP

The following instructions explain how to properly set your plotter up when using Graphtec Type 2

Half-Inch Registration Marks in a Print and Cut Workflow. If setting is not specified leave it at the default.

Press the menu button to access if the icons are not showing. Use the left arrow directional key to

go back a screen. Use the Enter button to save a change.

1 TOOL - DOWN ARROW TO SCREEN 2/3

2 DATA SORTING>

AREA-OFF, TOOL-OFF

(BACK TO)

4CONDITION PRIORITY>PROGRAM – If you are setting the speed and pressure in the software.(Flexi)

>MANUAL to use the CONDITONS in the Cutter control panel (Wasatch - Flexi option

2 ARMS -SCREEN 1/4

3 MARK SCAN MODE

1 MARK SCAN MODE - ARMS

2 NUMBER OF POINTS -DEFAULT IS 2, CHANGE TO 4

SET MARK TYPE -DOWN ARROW TO SCREEN 2/4

1 MARK TYPE -DEFAULT IS TYPE 2

3 MARK SIZE -DEFAULT IS.787” -CHANGE TO 0.5” (13mm)

V ADV -SCREEN 1/3

3 LENGTH UNIT>INCH

^INTERFACE SCREEN 1/3

1COMMAND

3AUTO

- IF APPLICABLE FOR ETHERNET OPTION -DOWN ARROW TO SCREEN 2/3

LAN

GATEWAY

4 MEDIA -SCREEN 1/2

1PREFEED -3.3’

2AUTO PREFEED

1ON

2PAGE LENGTH 3.3FT

3PAGE LENGTH-1968.5”

4INITIAL FEED

1OFF

SENSOR OFFSET ADJUST

Per Graphtec we need to begin using “Sensor Offset Adjust” rather than “Axis Origin Offset.” Both methods

result in shifting the cut lines but, the Sensor Offset Adjust will NOT move the ORIGIN point.

REMEMBER: Increase the X and Y values shift the cut lines to the upper left (if you are standing in front of the

cutter.) Y = (right to left, positive values shift left) X = (down to up, positive values shift cut lines up)

The Sensor Offset Adjust is done by doing the following:

1.) Ensure the customer has “Ready” displayed on the screen.

2.) Hit the “ENTER” key.

3.) Hit number “2” for the ARMS menu.

4.) Arrow down to “Sensor Offset Adjust”

5.) Hit “1” for “Sensor Offset Adjust”

6.) Hit number “3=X” or “4=Y”

7.) Arrow up or down to increase or decrease the values.

8.) Once the values are set hit the “left arrow” or “Previous” then hit enter to confirm.

Otros manuales para FC8000 Series

Tabla de contenidos

Otros manuales de Cortador de GRAPHTEC

GRAPHTEC

GRAPHTEC CUTTING PRO FC3100-60 Manual de usuario

GRAPHTEC

GRAPHTEC FCX4000 SERIES Manual de usuario

GRAPHTEC

GRAPHTEC CE5000 SERIES Manual de usuario

GRAPHTEC

GRAPHTEC CE LITE-50 Guía del usuario

GRAPHTEC

GRAPHTEC FC5100-75 Manual de usuario

GRAPHTEC

GRAPHTEC FC4500 Manual de usuario

GRAPHTEC

GRAPHTEC FCX2000 SERIES Manual de usuario

GRAPHTEC

GRAPHTEC FC2240 Manual de usuario

GRAPHTEC

GRAPHTEC CB15U Manual de usuario

Manuales populares de Cortador de otras marcas

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manual de usuario

Makita

Makita DCS552 Manual de usuario

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manual de usuario

Makita

Makita 4112HS Manual de usuario

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manual de usuario

Hitachi

Hitachi CM 4SB2 Guía de solución de problemas

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manual de usuario

GCC Technologies

GCC Technologies AFJ-24S Manual de usuario

DeWalt

DeWalt XR LI-ION DCS350N Manual de usuario

Baudat

Baudat ES1 Manual de usuario

Mafell

Mafell ZAF 200 Guía

Makita

Makita 4100NH Manual de usuario

Formax

Formax FD 574 Manual de usuario

EINHELL

EINHELL TE-MA 1500 Manual de usuario

Husqvarna

Husqvarna Cut-n-Break K 760 Manual de usuario

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manual de usuario

TRI tool

TRI tool 301A Manual de usuario

Roller

Roller King 1 1/4 Manual de usuario