Graco T-MAX 506 Manual
T-MAX™506/657
www.graco.com
START-UP
STAR-TUP Spray WITH Air <= 1.5 mm
Fill product hopper
with pre-mixed texture
product.
Turn pressure control
knob until steady stream
flows from product tube. Turn pump OFF.
Turn applicator OFF.
Turn ON/OFF switch
to ON.
Loosen nut on bottom
of pump
2-3 turns to
release pressure.
Turn pressure control to
maximum. To spray, aim
applicator at wall from
0.5 m distance wall and
open applicator.
To clean clogged tip, turn
applicator OFF, turn tip 180° to
CLEAN position, aim towards free
area, turn applicator ON. When
clog clears, turn applicator OFF
and tip to SPRAY postion.
Turn pressure
control off (0).
Aim applicator into
hopper.
Turn applicator ON.
2
DO NOT USE WITH
QUICK-SET MATERIALS
Pressure Relief
2
DO NOT USE WITH
QUICK-SET MATERIALS
Pressure
Relief
Use different
tip nozzle size
to adjust flow.
Install filter and tip
extension.
Connect applicator
to product tube.
Add water if thinning is
required. Mix thoroughly.
HDA531
HDA535
HDA541
HDA545
HDA651
HDA661
HDA671
mc03 m
c
52
Spray WITHOUT Air < .25 mm
Screw tip assembly
onto applicator.
Fill product hopper with
mixed texture product.
Place product tube into hopper, turn ON/OFF switch to ON.
Turn control knob to ‘green’ section and allow material to product 30 sec.
Turn pump control knob to
shut pump off.
Screw air hose and valve to applicator.
Connect product tube to gun.
Turn applicator valve OFF.
Insert air nozzle.
Hold applicator over
product hopper and turn
applicator ON.
Turn air compressor ON. Turn pump
control knob to ‘green’ section to
achieve desired product flow rate.
Regulate air valve for
proper atomization.
To stop spraying,
turn applicator OFF.
Quick Operator’s Guide
SET-UP
This procedure is for water-based paints and flushing agents. For solvent-based paints and flushing agents (i.e. mineral spirits), you must first
read the section on Fire and Explosion Hazards in the Operating Instructions. Please note this Quick Guide is at no means replacing the official
Graco manual. Graco can at no means be liable for any consequences of not following the safety regulations as stipulated in the official manual.
* Please check the Graco operations manual supplied with the unit for more details.
WARNING
Turn pump control off (0).
Plug electrical cord into grounded outlet.Connect pump module to hopper cart.
Remove pump plug.
Connect product tube to pump outlet.
PRESSURE RELEASE PROCESS
Turn pump control knob counter-clockwise,
to shut off pump.
Close applicator after pressure release.
Close air valve.
Scrape remaining product in
hopper into pump to be pumped
from sprayer.
Rotate pump control to
(0) to shut pump off.
Shut air compressor OFF if spraying with air.
Remove applicator from product tube.
Clean applicator.
Turn pump control
clockwise to start pump.
Turn pump control to (0) to
shut pump OFF.
Clean applicator, spray tips and
guard with brush.Set ON/OFF switch to OFF.
Turn pump control
clockwise to pump
unused texture product
out of product hopper
and tube.
Run pump until
cleaning ball exits
product hose.
Retrieve cleaning
ball. Repeat till water
comes out clear.
Insert moistened cleaning ball into pump.
Connect product tube to pump outlet.
Clean hardened product
from applicator nozzles
with air nozzle cleaner.
Remove drain plug from hopper.
Clean hopper with water, brush
and sponge. Insert drain plug.
Fill hopper with 1/3clear water.
GRACO DISTRIBUTION BVBA Industrieterrein Oude Bunders
Slakweidestraat 31 • B-3630 Maasmechelen
Tel: +32 (89) 770 700 • Fax: +32 (89) 770 777
www.graco.com
© 2018 GRACO DISTRIBUTION BVBA · Form No. 328033ENEU (revD)· 08/18 · Digital version only.
Graco is certified ISO 9001.
All information, illustrations, and specifications in this document are based on the latest product information available at the time of publication.
The right is reserved to make changes at any time without notice. For more information on Graco’s intellectual property, see www.graco.com/patent or www.graco.com/trademarks.
CHOOSE THE RIGHT TIP (HDA-XXX)
CLEAN-UP
XTRA LIGHT LIGHT MEDIUM HEAVY
HDA531 HDA541 HDA651 HDA671
HDA535 HDA545 HDA661 -
VERY FINE - 3 MM FINE - 4 MM MEDIUM - 6 MM MEDIUM HEAVY - 8 MM HEAVY - 10 MM
248888 248524 248525 248526 248527
Otros manuales para T-MAX 506
3
Este manual sirve para los siguientes modelos
1
Otros manuales de Pistola pulverizadora de pintura de Graco
Graco
Graco GTS-2500 B Series Manual de operación
Graco
Graco 17G807 Guía
Graco
Graco Contractor PC Guía
Graco
Graco GMax 233709 Manual de usuario
Graco
Graco Switch 3D Gun Manual de lista de piezas
Graco
Graco 232140 Manual de operación
Graco
Graco GMax 5900 Manual de instrucciones
Graco
Graco Reactor A-25 Manual de uso y cuidado
Graco
Graco King 96A388 Manual de usuario
Graco
Graco Xtreme XL 45 Manual de lista de piezas
Graco
Graco GH 200 Manual de instrucciones
Graco
Graco Mark V Premium Instrucciones de funcionamiento
Graco
Graco DURON Performance Max 395 Instrucciones de funcionamiento
Graco
Graco Field Lazer 248942 Manual de instrucciones
Graco
Graco Ultra 395 Manual de usuario
Graco
Graco EM 490 Manual de operación
Graco
Graco T Series Manual de operación
Graco
Graco T-MAX 506 Manual de uso y cuidado
Graco
Graco C Series Manual de usuario
Graco
Graco XPs-hf Series Manual de uso y cuidado
