Grace Grace 901 Manual de usuario

Model 901

HEADPHONE AMPLIFIER

OWNERS MANUAL

PO Box 204 Boulder, CO 80306

tel: 303.443.7454 fax: 303.444.4634

email: [email protected] web: www.gracedesign.com

Thank you for purchasing the Model 901 headphone amplifier. It is

designed to be completely reliable and easy to use.However, we ask that you

take the time to familiarize yourself with some of the more important operation

instructions in this manual to avoid most common user problems.

The Model 901 amplifier is an ultra high fidelity monitoring device.By

revealing all of the contents of your signal,we hope it helps you achieve a new

level of excellence in your audio recordings.

Feel free to check out our internet web page for the latest information

regarding your amplifier. You can always find the latest owners manuals and

other technical documents at:

http://www.gracedesign.com/documents/docs.html

MODEL 901 FEATURES

•Balanced XLR analog inputs

•Unbalanced RCA analog inputs

•AES, SPDIF and TOS LINK digital inputs

•High current output amplifier drives 8 Ohm loads

•24 position level attenuator with .05dB channel matching

•Internal linear power supply

•High current, low noise torroidal power transformer

•No electrolytic capacitors in the signal path

•Highest quality metal film resistors

•Ultra low distortion 24 bit DAC accepts sample rates up to 96kHz

•Automatic digital de-emphasis filter

•10dB gain boost switch for -10 sources

•Fast, musical transipedance output amplifiers

•Precision instrumentation balanced input amplifiers

•Sealed gold contact relays for input select and gain boost switching

FRONT PANEL CONTROLS

LEVEL CONTROL The 901 level control is assembled with an ultra precision

24 position gold contact switch. Using low inductance surface mount metal

film resistors this switch is the ultimate attenuator for sonic fidelity and level

accuracy. Left-right channel balance is maintained to within 0.05dB at any

setting. The attenuation curve is shown in the table below.

POSITION ATTENUATION POSITION ATTENUATION POSITION ATTENUATION

24 016 -16 8-32

23 -215 -18 7-34

22 -414 -20 6-38

21 -613 -22 5-42

20 -812 -24 4-46

19 -10 11 -26 3-50

18 -12 10 -28 2-60

17 -14 9-30 1-∞

GAIN RANGE The gain range switch provides an extra 10dB of gain for

monitoring –10dB signals or use with low sensitivity headphones. With the

LEVEL CONTROL at maximum, the LOWgain position provides +10dB overall

gain when using the analog inputs. When using the digital input, this setting

will yield +20dBu out at 0dBFS. When the GAIN RANGE switch is depressed

the overall gain is +20dB

LEVEL CONTROL SAMPLE RATE

INDICATOR POWER SWITCH

GAIN RANGE INPUT SELECT OUTPUT JACK

INPUT SELECT This switch selects the input source. With the switch out the

analog inputs are selected. XLR balanced and RCA unbalanced connectors

are provided on the rear panel. When the INPUT SELECT switch is depressed

the digital inputs are selected. AES3, S/PDIF and optical inputs are provided

on the rear panel. A toggle switch on the rear panel selects between the AES

and S/PDIF-optical inputs.

SAMPLE RATE INDICATORSThe LED sample rate indicators display the

digital input signal sample rate. The sample rate is determined by a frequency

comparator, not by the sample rate bits in the digital data. This ensures that

the proper DAC filter settings are used even ifthere are erroneous sample rate

bits in the signal. Sample rates of 44.1, 48, 88.2 and 96kHz are directly

indicated. 32kHz is indicated when the 44.1 and 96 LEDs are both illuminated.

OUTPUT JACK The two output jacks are wired in parallel so that two sets of

headphones can be used simultaneously. They are wired left channel to the

tip, right channel to the ring and ground to the sleeve.

POWER SWITCH The power switch connects power from the AC input

module to the preamplifier circuitry. When depressed, the POWER SWITCH

will illuminate.

REAR PANEL CONTROLS

AC INLET The 901 accommodates a standard IEC power cable. The IEC inlet

contains a built in RFI filter.

LINE VOLTAGE SELECTOR To change the line voltage use a small screwdriver to pry

open the voltage select door. Carefully remove the voltage select cam and insert with the

desired voltage showing. Use the table below for voltage settings and fuse values.

CAM SETTING LINE VOLTAGE FUSE VALUE

110Vac 100Vac 120Vac .25A SLOW

220Vac 220Vac 230Vac 240Vac .125A SLOW

WARNING: The Model 901 is capable of delivering over .5 Amperes of

current to the headphone jack. The nature of the TRS jack allows for the ring

to be shorted to the sleeve when the plug is partially inserted. If the plug is

left partially inserted andthere is a high amplitude signal on the output of the

amplifier the line fuse will blow. Always replace the line fuse with the proper

type fuse or damage to the amplifier can occur. Note that this fault condition

will not harm your headphones.

DIGITAL IN SELECTOR The digital input selector switch selects either AES or S/PDIF and

optical signals. When the switch is set in the S/PDIF/optical position either input can be

used but only one can be used at a time.

ANALOG INPUTS The 901 provides both balanced and unbalanced inputs. Input

connections are made using the female XLR connector on the rear panel. These

connectorsare wired with pin 2 positive, pin 3 negative and pin 1 ground. The unbalanced

phono type jacks are wired in parallel with pin 2 of the XLR balanced jacks. Connecting

unbalanced and balanced signals simultaneously is not recommended.

Model 901 Specifications

GAIN

Normal Mode -∞to +10dB

Boost Mode -∞to +20dB

FREQUENCY RESPONSE

@ 0dBu out +/-.25dB 22Hz -120kHz

@ 0dBu out +/-.5dB 12Hz -260kHz

@ 0dBu out +/-3dB 4Hz -600kHz

MAXIMUM OUTPUT LEVEL

@ 1kHz, 50 Ohm load +23dBu (10.9Vrms, 30.8V p-p)

INPUT IMPEDANCE

40K Ohms balanced

20K Ohms unbalanced

OUTPUT IMPEDANCE

5 Ohms

DYNAMIC RANGE

@ 0dB gain, 50 Ohm load 116dB

@ -10dB gain, 50 Ohm load 121dB

CMRR

3.5Vrms in, 10dB gain >75dB

DISTORTION

THD+N

10dB gain, +10dBu out, 50 Ohm load 0.0051%

SMPTE

4:1 10dB gain, +10dBu out, 50 Ohm load <0.012%

ATTENUATOR CHANNEL MATCHING <0.05dB

D\A SPECIFICATIONS

Input sample rate 44.1, 48, 88.2, 96kHz

Input word length 16 to 24 bits

THD+N

44.1kHz, 24bit, 1kHz, +20dBu out 0.0016%

NOISE FLOOR

0dB gain, 22-22kHz -95dBu

0dB gain, A-weighted -102dBu

POWER REQUIREMENTS

115VAC .16A

230VAC .08A

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario