Goldair GCV440 Manual de usuario

Operating Instructions

Model: GCV440

2300W Convector Heater with WiFi

CAUTION: In order to avoid a hazard due to inadvertent resetting of the

thermal cut-out, this appliance must not be supplied through an external

switching device, such as a timer, or connected to a circuit that is regularly

switched on and off by the utility.

•This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities or lack of experience and

knowledge, unless they are supervised or have been given instruction

concerning the use of the appliance by a person responsible for their safety.

•Children should be supervised to ensure that they do not play with the

appliance.

•If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

WARNING: You must not cover this appliance. Covering this appliance

presents fire risk and will activate the safety fuse; permanently disabling the

unit.

WARNING: Do not use this appliance in small rooms when they are

occupied by persons not capable of leaving the room on their own, unless

constant supervision is provided.

WARNING: To reduce the risk of fire, keep textiles, curtains, or any

flammable material a minimum distance of 1 metre from the air outlet.

General Care and Safety Guide

•Use only the voltage specified on the rating label of the appliance.

•Keep all objects at least 1 metre from the front, sides and rear of the

appliance.

•This appliance is intended for household use only and not for commercial or

industrial use.

•Indoor use only.

•Use this appliance only as described in this manual. Any other use is not

recommended by the manufacturer and may cause fire, electric shock or

injury.

•Do not use the appliance if it has been dropped or damaged.

•The common cause of overheating is deposits of dust or fluff in the appliance.

Ensure these deposits are removed regularly by unplugging the appliance and

vacuum cleaning the air vents and grills.

YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE

INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.

•Never use the appliance to dry clothes.

•Always unplug appliance when not in use.

•When the appliance has been unpacked, check it for transport damage and

ensure all parts have been delivered. If parts are missing or the appliance has

been damaged, contact the Customer Services Team.

•Do not use if there are visible signs of damage to the appliance.

•Do not connect the appliance to mains supply until completely assembled and

adjusted.

•Ensure hands are dry before handling the plug or main unit.

•Ensure appliance is on a flat, stable, heat-resistant surface.

•Do not operate with cord set coiled up as a heat build up is likely, which could

be sufficient to become a hazard.

•Carry out regular checks of the supply cord to ensure no damage is evident

•Do not operate this appliance with a damaged cord, plug or after the appliance

malfunctions or has been dropped or damaged in any manner. Take to a

qualified electrical person for examination, electrical service or repair.

•Do not twist, kink or wrap the cord around the appliance, as this may cause the

insulation to weaken and split. Always ensure that all cord has been removed

from any cord storage area and is unrolled before use.

•It is recommended that this appliance is plugged directly into the wall socket.

Power boards are not rated to supply power to high wattage appliances.

•A correctly specified, undamaged extension cord may be used with this

appliance provided it is used in a safe manner.

•Do not remove plug from power socket until the appliance has been switched

off.

•Do not remove plug from power socket by pulling cord; always grip plug.

•Do not place cord under carpet or cover with rugs or furniture. Arrange the cord

so it cannot be tripped over.

•Don’t place appliance on bedding or on thick & long carpet where the openings

may get blocked.

•Switch off and use handle provided when moving

•Do not place appliance close to radiant heat source.

•Do not insert or allow foreign objects to enter any ventilation or exhaust

opening, as this may cause an electric shock, fire or damage to the appliance.

•Do not sit on the appliance.

•Do not use abrasive cleaning products on this appliance. Clean with a damp

cloth (not wet) rinsed in hot soapy water only. Always remove plug from the

mains supply before cleaning.

•Do not operate in areas where petrol, paint or other flammable liquids are used

or stored.

•Do not use this appliance in the immediate surrounds of a bath, a shower, or a

swimming pool or other liquids.

General Care and Safety Guide

•The appliance must not be immersed in any liquids.

•There are no user serviceable parts installed in the unit.

•Do not place the unit in wardrobes or other enclosed spaces as this may cause

fire hazards.

•This unit is not supposed to be used in or around locations where foodstuffs,

works of art or delicate articles of science, etc. are stored.

•If your appliance does not work, or is not working properly, contact the place of

purchase or the Customer Services Team.

General Care and Safety Guide

The remote control supplied with this appliance uses a CR2032 coin type

battery.

DANGER IF SWALLOWED OR PLACED INSIDE ANY PART

OF THE BODY

WARNING!

Button/Coin Cell Batteries are hazardous and must be kept out of reach of

children at all times, whether the battery is new or used. These batteries

can cause severe or fatal injuries in 2 hours or less if swallowed or placed

inside any part of the body. Dispose of used batteries immediately.

If it is suspected a button/coin cell battery has been swallowed or placed

inside any part of the body, seek medical attention immediately or for 24/7

fast, expert advice, contact

Australian Poisons Information Centre on 13 11 26

New Zealand National Poisons Information Centre on 0800 764 766

THIS PRODUCT CONTAINS

BUTTON/COIN CELL BATTERIES

KEEP OUT OF REACH

OF CHILDREN

Components

ASSEMBLY

Before using the heater, the feet (supplied separately in the carton), must be fitted to the unit. The

screw pack to attach the feet to your heater will be taped to either one of the feet for your heater or

taped to the plug.

Carefully turn the Main Body upside-down on a scratch-free and

stable surface. Be careful to prevent damage to the cosmetic finish

or your floor surfacing.

Before the appliance can be used, the feet must be screwed on as

follows:

1. Unpack the appliance from the packaging.

2. Remove the transport packaging.

3. Check that the appliance shows no signs of damage.

4. Slide the feet from the outside into the corresponding supports

on the underside of the heater.

5. Secure the feet firmly using the screws supplied.

WARNING: Operate the heater in the normal upright position only with the feet

attached to the bottom. Any other position could create a hazardous situation.

WARNING: Heater must not be used without the feet fitted.

This appliance has been supplied with ‘1 way screws’ for permanent installation of the feet.

This is a safety requirement for the New Zealand and Australian market.

Operating Your Heater

Always choose a safe location for the heater, keeping in mind the safety precautions

outlined. Ensure all packaging has been removed from the unit before use. Please

follow the below instructions.

WARNING: In order to avoid overheating or fire, do not cover the heater.

WARNING: Keep all objects at least 1 metre from the front, sides and rear

of the appliance.

WARNING: Do not use this heater with a programmer, separate timer,

remote-control system or any other device that switches the heater on

automatically, since a fire risk exists if the heater is covered or positioned

incorrectly.

WARNING:Never leave this heater unattended when in use.

Ensure heater is on a flat, stable, heat-resistant surface.

Once the heater is in a safe operating position and all switches are in the off

position, insert the power plug into the mains outlet and switch on.

CAUTION: Ensure the power cord is not tight because if pulled it may

partially pull the plug from the socket. A partially inserted plug will overheat

the plug and socket and could result in fire.

Note: When the appliance is turned on for the first time, it may release a

slight odour or smoke. This odour or smoke is a normal occurrence caused by

the initial heating of the internal heating elements and should not occur

again.

POWER

Switch the main power button on which is located on the end of the heater.

After the power is turned on, the computer board emits a ‘click’ and the screen displays the

current room temperature.

Press the On\Off key once to enter the standby state.

HEAT SETTING

Press the ‘Heat Setting’ button to adjust the heat setting from 1000W to 1300W to 2300W & ANTI-

FROST.

In anti-frost: If the heater is in standby and the room temperature is lower than 5°C, the heater will

automatically turn on to HIGH heating mode. When the room temperature reaches 9°C, the

heating is turned back to standby. This cycle will repeat as required.

TEMPERATURE

The set temperature is displayed every time the appliance is power up.The temperature can be set

when the appliance is in stand-by or heating.

Press the ‘+’ or ‘-’buttons to set the desired room temperature.

The temperature range is 5°C-37°C.

The appliance can hold the last temperature setting in its memory. This temperature will be shown

at each start-up.

TIMER

Press the timer button, each time the time is increased by 1 hour up to 24 hours. Once the timer is

set, the timer countdown starts after 5 seconds. When the set time has elapsed, the heater will go

back into standby mode.

To cancel the timer, press the timer button until the display read 0h 00m.

Operating your Heater

1. Selected heating level display

2. ‘Fan’ symbol

3. ‘Frost protection’ symbol

4. Selected unit of measurement display

5. Fan button

6. Increase temperature

7. Reduce temperature

8. Timer button

9. Running time display

10. Set temperature display

11. Measured temperature display

12. On/Off button

13. Infrared receiver for remote control

14. Wi-Fi button

15. Heat Setting Button

16. Wi-Fi indicator lamp

FAN

Press the fan button to turn the fan on. Press it again to turn the fan off. The fan symbol will appear

on the screen.

WiFi –Downloading and Setting up APP

This APP is supported only on 2.4GHz Wi-Fi channels. Please ensure your phone is

2.4GHz capable

Note this device will only work within your home WIFI system.

This does not operate on 3G or 4G internet connections.

You will need a connection to your home Wi-Fi.

•Tap REGISTER near the bottom of the screen.

•Read and agree to the Privacy Policy.

•Add your email address.

•Tap 'Obtain verification code'

You will then receive an email with a verification

code.

Download Goldair mobile APP

•Open the APP Store or Google Play on your mobile phone.

•Open 'Search' and enter 'Goldair'

•Click 'GET' and begin to download and install.

Once downloaded to your phone open the APP

•Enter the verification code from your email.

•Create a password.

•Then tap confirm.

If you haven't received a verification code via

email, tap the resend button and when the

verification code is received follow above steps.

Your APP is now registered and ready for pairing

to your device.

Pairing APP to Device

Details for pairing this heater to the Goldair App can be found at the below website link.

Either scan the QR code below or enter the website into your browser.

https://www.goldair.co.nz/

goldair-app

New Zealand Products

https://www.goldair.com.au/

goldair-app

Australia Products

Pairing Mode

To connect to the Goldair app you must ensure that your device is in

pairing mode which is where the Wifi Icon is flashing.

Most products will be in pairing mode after switching the device on

but if it is not:

- Put device on STAND-BY mode (ON at the wall but device is OFF)

- Hold down the small black button on the back of the heater for

around 5 seconds or until the Wifi icon begins to flash.

SUPPORT AND TECHNICAL ADVICE

Goldair –New Zealand

Monday –Friday 8am-5pm

Phone +64 (0)9 917 4000

Phone 0800 232 633

[email protected]

Goldair –Australia

Monday –Friday 8am-5pm

Phone +61 (0)3 9365 5100

Phone 1300 465 324

info@cdbgoldair.com.au

PROOF OF PURCHASE

To receive warranty retain receipt as proof of purchase.

Operating Your Heater

SAFETY DEVICES

This appliance has three protection devices:

•Tilt Switch - this will automatically turn the appliance off if the appliance is not in

the correct operating position.

•Resettable Thermal Link - this will automatically disconnect the power to the

appliance at a pre-set overheat temperature. After cooling down it will reset and

power on again. If this occurs, investigate what is causing the appliance to

overheat.

CAUTION: The appliance generates heat during use. Precautions must be

taken to prevent the risk of burns, scalds, fires or other damage to persons.

CARE AND CLEANING

•The heater requires regular cleaning to ensure trouble free operation:

•Unplug the heater from the mains supply before cleaning.

•Ensure that the heater has been allowed to cool down completely before cleaning.

•The common cause of overheating is deposits of dust or fluff in the appliance.

Ensure these deposits are removed regularly by unplugging the appliance and

vacuum cleaning the air vents and grills.

•Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and

dirt.

•Never use solutions such as petrol, thinners or polishing agents.

•Ensure the heater is dry before plugging back into the mains supply.

•Do not attempt to dismantle the appliance.

•There are no user serviceable parts. For service or repair, contact an authorised

electrical service technician

Tabla de contenidos

Otros manuales de Calentador de Goldair

Goldair

Goldair GFH150 Manual de usuario

Goldair

Goldair GCH250B Manual de usuario

Goldair

Goldair PLATINUM GPTF480 Manual de usuario

Goldair

Goldair 3514TC Manual de usuario

Goldair

Goldair GOC207TH Hoja de instrucciones

Goldair

Goldair GCT325R Manual de usuario

Goldair

Goldair Select GSCH250R Manual de usuario

Goldair

Goldair GFH530 Manual de usuario

Goldair

Goldair GCV280 Manual de usuario

Goldair

Goldair GGPH224B Manual de usuario

Goldair

Goldair GSFH210 Manual de usuario

Goldair

Goldair Platinum GPPH610 Manual de usuario

Goldair

Goldair GCT430 Manual de usuario

Goldair

Goldair GCH320 Manual de usuario

Goldair

Goldair GCH255B Manual de usuario

Goldair

Goldair Platinum GPOC407 Manual de usuario

Goldair

Goldair GPCT440 Manual de usuario

Goldair

Goldair GFH230 Manual de usuario

Goldair

Goldair Platinum GPPH220 Manual de usuario

Goldair

Goldair Select GSCH215 Manual de usuario

Goldair

Goldair GMH220 Manual de usuario

Goldair

Goldair GMH230 Manual de usuario

Goldair

Goldair GCW220 Manual de usuario

Goldair

Goldair PLATINUM GPCW100 Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario