Godex G500 Manual de usuario
USER MANUAL
G500 SERIES
User Manual
Version
Issue Date
P/N
: G500 series
: Rev 1.3
: 2012.11.07
: 920-014011-00
附錄
產品規格
G500 Series
機種 G500 G530
列印模式 熱感式/熱轉式兩用
解析度 203 dpi (8 dot/mm) 300 dpi (12 dot/mm)
列印速度 5 IPS (127 mm/s) 4 IPS (102 mm/s)
列印寬度 4.25” (108 mm) 4.16” (105.7 mm)
列印長度
Min. 0.16” (4 mm)**
Max. 68” (1727 mm)
Min. 0.39” (10 mm)
Max. 30” (762 mm)
記憶體
8MB Flash (使用者可用容量為4MB)
16MB SDRAM
感應器形式 反射式感應器: 可移動式; 透光式感應器: 中置型固定式
紙張規格
紙張類型
連續紙、間距標籤紙、黑線標記紙或打孔紙等，標籤長度可自動偵測或手動命令強制
控制。
紙張寬度 1” (25.4 mm) Min. - 4.64” (118 mm) Max.
紙張厚度 0.003” (0.06 mm) Min. - 0.01” (0.25 mm) Max
紙捲外徑 Max. 5” (127 mm)
紙捲軸芯 1”, 1.5”, 3” (25.4 mm, 38.1 mm, 76.2 mm)
碳帶規格
材質 一般蠟質型、混合型、抗刮樹脂型
長度 981’ (300 m)
寬度 1.18” Min - 4.33” (30 mm - 110 mm) Max
最大外徑 2.67“ (68 mm)
軸芯 1” (25.4 mm)
程式語言
隨機搭贈軟體
標籤排版軟體
Driver 支援Windows 2000, XP, Vista, 7, Windows Server 2003 & 2008
附錄_產品規格
039
DLL 支援Windows 2000, XP and Vista
處理器 32 Bit RISC CPU
EZPL, GEPL, GZPL auto switch
GoLabel (for EZPL only)
SAFETY INSTRUCTIONS Please read the following instructions carefully.
Keep the equipment away from humidity.
Before you connect the equipment to the power outlet, please check the voltage of the power
source.
Make sure the printer is off before plugging the power connector into the power jack.
It is recommended that you connect the printer to a surge protector to prevent possible
transient overvoltage damage.
Be careful not to get liquid on the equipment to avoid electrical shock.
For safety and warranty reasons, ONLY qualified service personnel should open the equipment.
Do not repair or adjust energized equipment under any circumstances.
G500 Series
Safety Instructions
P/N : 920-014011-00
1
Barcode Printer
001
1 Barcode Printer
G500 Series
Box Content
Please check that all of the following items are included with your printer.
Barcode Printer
Power Cord
AC Adapter
USB Cable
Ribbon
Label Stock
1-1
Ribbon Hubs ( set of 2 )
Empty Ribbon Core
Label Supply Hub
Label Guide Plates ( set of 2 )
Quick Reference Guide
CD ( with QLabel software / user manual )
2
1 Barcode Printer
G500 Series
Getting To Know Your Printer
Device Overview
Front View
Rear View
1-2
TOP COVER
COVER OPEN BUTTONS
Release buttons for opening the printer cover
FRONT COVER
SERIAL PORT ( RS-232 )*
POWER SWITCH
- ON
- OFF
FAN-FOLD LABEL INSERT
Feed slot for external label feeding
POWER JACK
USB PORT
Barcode Printer
002
OPERATION PANEL
The combination of connection ports may vary with printer model.
NOTICE
ETHERNET PORT*
3
1 Barcode Printer
G500 Series
Open The Printer Cover
Open The Printing Mechanism
ADJUSTMENT SCREW ( LEFT )
Screw for adjusting the print head pressure
ADJUSTMENT SCREW ( RIGHT )
Screw for adjusting the print head pressure
LABEL SUPPLY MODULE
- LABEL SUPPLY HUB
- LABEL GUIDE PLATES ( SET of 2 )
RIBBON MODULE
- RIBBON FEED MECHANISM
- RIBBON HUB
- EMPTY RIBBON CORE
LABEL GUIDE ( RIGHT )
RELEASE CATCH ( RIGHT )
RIBBON SUPPLY HUB
RELEASE CATCH ( LEFT )
LABEL GUIDE ( LEFT )
PRINTING MECHANISM
PLATEN
LABEL SENSOR
Movable
ADJUSTMENT SCREW
Screw for adjusting
the print line
Barcode Printer
003
4
2 Printer Setup
G500 Series
Open The Printer Cover
Pressing The Cover Open Buttons
Place the printer on a flat surface. Open the printer cover by pressing the release buttons on both sides of the
printer housing and lift the cover.
Open The Printing Mechanism
Pressing The Release Catches
Release and lift the printing mechanism.
2-1
Pressing the button
COVER OPEN BUTTONS
Release buttons for opening the printer cover.
Pressing the button
Lift the printer cover backward
Lift the printing mechanism
Pressing
Pressing
RELEASE CATCHES
2-2
Printer Setup
004
5
2 Printer Setup
G500 Series
Loading The Ribbon
A New Ribbon Module Installation
Place the new ribbon on the hub which forms a ribbon supply hub.
Place the empty ribbon core on the hub which forms a ribbon rewind hub.
Stick the ribbon supply hub on the ribbon rewind hub and wind the rewind hub 2~3 circles.
2-3
RIBBON SUPPLY HUB
Place on the hub
RIBBON HUB NEW RIBBON
Place on the hub
EMPTY RIBBON CORERIBBON HUB
RIBBON FEED MODULE
Printer Setup
005
Wind the ribbon around the core
6
2 Printer Setup
G500 Series
Install The Ribbon On The Printer
Place the ribbon supply hub at the back of the printing mechanism.
Pass the ribbon supply hub under the print head.
Insert the ribbon rewind hub on the ribbon feed mechanism.
Close the printing mechanism, making sure that it clicks into place.
Place on the printing mechanism
RIBBON FEED MECHANISM
Wind to the back
Insert into the printing mechanism
Printer Setup
006
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Lector de código de barras de Godex
Godex
Godex EZ-1100Plus Manual de usuario
Godex
Godex EZ-2000 PLUS Manual de usuario
Godex
Godex RT700i Manual de usuario
Godex
Godex GS500 Instrucciones de funcionamiento y mantenimiento
Godex
Godex ZX1200i Manual de usuario
Godex
Godex EZ-1105 Manual de usuario
Godex
Godex GS220 Manual de usuario
Godex
Godex RT800i Series Manual de usuario
Godex
Godex ZX1200i Manual de usuario
Godex
Godex RT800i Series Manual de usuario
Godex
Godex EZ2050 Manual de usuario
Godex
Godex EZ100 Series Manual de usuario
Godex
Godex RT200i Manual de usuario
Godex
Godex GS550 Manual de usuario
Godex
Godex EZ-1105 Manual de usuario
Godex
Godex GS220 Manual de usuario
Godex
Godex G525 Manual de usuario
Godex
Godex BP300 Manual de usuario
Godex
Godex GS550 Manual de usuario
Godex
Godex AP16-F Manual de usuario
