GMI PS500 Guía de instalación

Detection,Protection, Innovation

PS500 USER TRAINING

Iss.A

Detection,Protection, Innovation

•Single Button User Operation

•Integral Impact Resistant Housing

•Graphic Display with Screen Light

•4 Gases Detected Simultaneously

•High Intensity Audible / Visual Alarms

•Datalogging

•Infrared interface for data download

•Rechargeable battery

Detection,Protection, Innovation

•Certification

Hazardous areas –flammable atmospheres:

−ATEX -required for all member countries of the EU

−UL - allows use in America

Performance testing:

−MED (Ships’ Wheelmark) -EU Marine Equipment Directive

Detection,Protection, Innovation

•Ranges of Operation

–4 gases are monitored:

•0-100% LEL propane

•0-25% Oxygen (O2)

•0-1000 ppm Carbon Monoxide (CO)

•0-5% Carbon Dioxide (CO2)

•NB: this slideshow shows pics of 5 gas version

–Gases displayed simultaneously

Detection,Protection, Innovation

•Operating Procedure

–Check the Following Before Use:

•instrument is clean and in good condition

•battery is fully charged and fitted correctly

•Sensor gas inlets are clean and in good condition

•all gas ranges are operational and the instrument is zeroed

•instrument is within the calibration period

–Switch on in Fresh Air / No Faults Displayed

Detection,Protection, Innovation

•Switching the Instrument On

−Press and Hold right button for 1 s.

−Instrument begins warm-up routine. During 30 second

warm-up a countdown timer appears on the screen

−The instrument display identifies the model, serial number,

software version, datalogging option and battery status

during warm-up.

Detection,Protection, Innovation

•Warm-up Information

−Time and Date

•The time and date from the instrument’s built-in clock is displayed

−Calibration Required

•If the display below appears (audible / visual alarms are also

activated), the instrument has detected a fault in the calibration

memory. It must be switched off.

Detection,Protection, Innovation

•Warm-up Information

–Calibration Due Date

•The calibration due date is shown on the display

•If the calibration due date has expired, the audible and visual alarm

activates

•Press right Button once to acknowledge overdue calibration due date,

cancel alarms and continue with warm-up

Detection,Protection, Innovation

•Warm-up Information

–Sensor Confirmation Check

•A diamond symbol appears above each sensor to confirm

that the sensor

–has been recognised

–is working correctly

–is being zeroed

•When sensors are zeroed correctly a tick appears above each

sensor

Detection,Protection, Innovation

•Warm-up Information

–Sensor Check Failure

•If sensor(s) fail the zero check at the end of warm-up, the audible and visual

alarms activate. The instrument display will show a spanner symbol.

•To acknowledge the alarm, press the right button. This clears the audible / visual

alarm. The instrument display will show a flashing spanner symbol alternating with

the faulty sensor zero reading.

alternating

with

Otros manuales para PS500

Tabla de contenidos

Otros manuales de Instrumento de medición de GMI

GMI

GMI PS200 series Instrucciones de funcionamiento

GMI

GMI PS200 series Guía del usuario

GMI

GMI GDUnet Manual de instrucciones

GMI

GMI PS200 series Manual de instrucciones

GMI

GMI PS1 Manual de instrucciones

GMI

GMI First Responder Manual de instrucciones

GMI

GMI GT series Manual de usuario

GMI

GMI GT series Manual de instrucciones

GMI

GMI Gasurveyor 6 - 500 Manual de instrucciones

GMI

GMI PS200 series Manual de usuario

GMI

GMI PS1 Guía del usuario

GMI

GMI V!SA Manual de instrucciones

GMI

GMI GT series Manual de instrucciones

GMI

GMI PS241 Manual de instrucciones

GMI

GMI PS200 series Manual de usuario

GMI

GMI Gasurveyor 500 Series Guía de instalación

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario