Global American Inc. 3307980 Manual de usuario
User’s Manual
3.5"xEmbeddedxController.
3307980
AMD Geode LX
Version 1.0
Copyrights
This manual is copyrighted and all rights are reserved. It does not allow any non authorization in
copied, photocopied, translated or reproduced to any electronic or machine readable form in
whole or in part without prior written consent from the manufacturer.
In general, the manufacturer will not be liable for any direct, indirect, special, incidental or
consequential damages arising from the use of inability to use the product or documentation, even
if advised of the possibility of such damages. The manufacturer keeps the rights in the subject to
change the contents of this manual without prior notices in order to improve the function design,
performance, quality and reliability. The author assumes no responsibility for any errors or
omissions, which may appear in this manual, nor does it make a commitment to update the
information contained herein.
Trademarks
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
All other trademarks, products and or product's name mentioned herein are mentioned for
identification purposes only, and may be trademarks and/or registered trademarks of their
respective companies or owners.
iii
Table of Contents
Introduction .......................................................1
Product Description.............................................................1
Checklist..............................................................................2
Specifications......................................................................3
Board Dimensions...............................................................4
Installations .......................................................5
Installing the Memory .........................................................6
Setting the Jumpers.............................................................7
Connectors on 3307980.....................................................10
Appendix ...........................................................19
A. I/O Port Address Map...................................................19
B. Interrupt Request Lines(IRQ)......................................20
C. Watchdog Timer Configuration....................................21
INTRODUCTION
1
Introduction
Product Description
The 33079803.5-inch disk size SBC incorporates the AMD Geode LX
processor with speeds of 433MHz (LX700) or 500MHz (LX800). It
comes with one DDR SO-DIMM socket that has a capacity of 1GB
system memory. The board supports one 10/100Mbps Ethernet, using a
Realtek RTL8100C controller. A 2D graphics controller comes
integrated on the board that supports CRT and TFT LCD displays.
Useful interface includes four USB 2.0 ports, 2 COM ports, and one
PCI-104 expansion slot. Other expansion options are available with the
Compact Flash socket and PCMCIA connector.
3307980
FEATURES:
-Embedded AMD Geode LX processor, 433MHz (LX700) /
500MHz (LX800)
-DDR SO-DIMM x 1, Max. 1GB
-Realtek RTL8100C 10/100Mbps Ethernet
-Integrated LX800/LX700 2D VGA controller, supports CRT
and TFT LCD display
-4 x USB 2.0, 2 x COM, CF socket, Watchdog timer, Digital I/O
-PCI-104 expansion, optional PCMCIA connector
-Dimensions: 145mm x 102mm (5.7” x 4”)
INTRODUCTION
2
3307980 User’s Manual
Checklist
Your 3307980package should include the items listed below.
•The 3307980AMD Geode LX 3.5-inch Disk Size SBC
•This User’s Manual
•1 CD containing chipset drivers and flash memory utility
•Optional cables
INTRODUCTION
3
Specifications
[
CPU AMD Geode LX CPU, 481-ball BGA
CPU Internal
Speed LX800 @500MHz
LX700 @433MHz
Power
Management APM
BIOS Award BIOS
Chipset AMD CS5536 I/O companion multi-function south bridge
Memory One DDR SO-DIMM socket, Max. up to 1GB
Graphic LX800/LX700 built-in high performance 2D graphic controller,
supports TFT, LVDS LCD & CRT display
LVDS 24-bit single channel LVDS
Ethernet Realtek RTL8100C-LF 10/100Mbps Ethernet chip
IDE CS5536 built-in one channel UDMA100 IDE
- 44-pin header x1
- Compact Flash (type II) connector x1
Audio Realtek ALC203 AC97 audio codec, supports 2-CH Line-Out,
Line-In & MIC
USB CS5536 built-in USB2.0 controller, support 4 ports
PCMCIA TI PCI1510 Card bus controller (3307980B only)
LPC I/O Winbond W83627HF: KB/Mouse controller, Parallel, IrDA,
Floppy, COM1, COM2 (RS232) & Hardware monitor (3 thermal
inputs, 4 voltage monitor inputs, VID0-4 & 2 Fan Headers)
PCI Arbiter AT209S PCI arbiter/clock buffer, extend PCI devices (master)
from 1 to 3
RTC CS5536 built-in, with on board Lithium battery
Edge Connectors DB-9 connector x1 for COM1 (RS232 only)
6-pins Mini-DIN connector x1 for PS/2 KB & Mouse (Y cable)
USB connector x1 for USB0
DB-15 connector x1 for CRT
RJ-45 connector x1 for LAN
Onboard Headers PCMCIA connector x1 for Card Bus (3307980B only)
DF13-20 header x1 for LVDS channel
Compact Flash Socket x1 for CF card
10-pin header x1 for COM2 (RS232 only)
4-pin header for USB1
10-pin header x1 for USB2, 3
26-pin header x1 for LPT port
44-pin header x1 for IDE
34-pin header x1 for FDD
12-pin header x1 for Audio
4-pin header x1 for IrDA
10-pin header x1 for Digital I/O
44-pin header x1 for TFT LCD panel
Expansion Slot PCI-104 w/ 4 mounting holes
Digital I/O Supports 4 In / 4 Out
Power +12V DC-in
Watchdog Timer Software programmable, supports 1~255 sec. system reset
RoHS Compliant Yes
Board Size 145 x 102mm
INTRODUCTION
4
3307980 User’s Manual
Board Dimensions
5
Installations
This section provides information on how to use the jumpers and
connectors on the 3307980 in order to set up a workable system. The topics
covered are:
Installing the Memory.................................................................. 6
Setting the Jumpers...................................................................... 7
Connectors on 3307980 ............................................................. 10
6
Installing the Memory
The 3307980 board supports one SODIMM DDR memory socket for a
maximum total memory. The memory module capacities supported are
128MB, 256MB, 512MB and 1GB.
Installing and Removing Memory Modules
To install the DDR modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR module so that the key of the DDR module align with
those on the memory slot. Insert the module into the socket at a slight
angle (approximately 30 degrees). Note that the socket and module
are both keyed, which means that the module can be installed only in
one direction.
2. To seat the memory module into the socket, apply firm and even
pressure to each end of the module until you feel it slip down into the
socket.
3. With the module properly seated in the socket, rotate the module
downward. Continue pressing downward until the clips at each end
lock into position.
4. To remove the DDR module, press the clips with both hands.
7
Setting the Jumpers
Jumpers are used on 3307980 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on 3307980 and their respective functions.
Jumper Locations on 3307980 ....................................................... 8
JP1: LVDS VDD Select (5V / 3.3V).............................................. 9
JP2: CF Connector master/Slave Setting........................................ 9
JP3: Clear CMOS Setting............................................................... 9
Tabla de contenidos
Otros manuales de Controladores de Global American Inc.
