C mpleting the Installati n
1. After the initial installation, be sure to check the pump operation by filling the
sump with water and observing the pump through one full cycle. When using the
Ultimate Sensor, the pump should run for 10 seconds after the water level reaches
the bottom of the sensor rod.
2. Replace the pit cover making sure not to pinch or crimp the pump wire with the
cover. The pit cover either has a ‘hole punch’ that will allow the cord to be
passed through it, or a hole can be drilled in the cover.
Understanding the Warnings & Alarms
AC p wer is ut
There are several causes for power
failure. The most common causes are
a power outage by the electric
company or a tripped circuit breaker.
Although the Ultimate Controller can
not run the pump, it will sound an
alarm indicating the loss of power.
This will allow the homeowner to
address the problem.
If this warning light and alarm are
on, the control box is not receiving
AC power for one of many reasons:
1. The control box is not plugged in
2. The power to the house is out
3. The circuit breaker to that outlet
has been tripped
4. The ground fault interrupter on
that outlet has been tripped
5. A power brownout is taking place
P wer Failure Alarm slide switch
When the controller is not receiving
AC power, the monitoring features
and the audible alarms are powered
by the 9-volt battery. This type of battery will power the controller for many hours,
but not indefinitely. nce the source of the AC power alarm is determined, it is
suggested that the Power Failure Alarm slide switch be turned to the OFF position
until the power is restored. This will preserve the battery and silence the alarm.
When AC power is restored, slide this switch back to the ON position.
Note: If the AC ower is restored and the slide switch is in the OFF osition, the alarm
and light for the 9-volt battery warning will activate, even if the battery is good. This
is a reminder to reset the alarm. Slide the switch to the ON osition. If the battery is
good, the light will go out. If the alarm continues to sound, re lace the battery.
The system is perating
This light should be ON and flashing at all times. It is included to indicate that the
system is monitoring the sump conditions. This light will not illuminate when:
1. The power is out and the Power Failure Alarm slide switch is in the OFF position
2. The power is out and the 9V battery is discharged
3. The controller is not functioning. Contact the Glentronics service department
The 9-v lt battery is l w
1. The 9-volt battery located in the top of the control box is coming to the end of
its useful life. Replace it with a new 9-volt alkaline battery.
2. The Power Failure Alarm switch is in the OFF position. It must be in the ON
position at all times, except when silencing an actual power failure condition.
Pump r sens r pr blem
This key feature monitors the time that the sensor has been activated. It is unusual
for a pump to run for 10 or more minutes continuously. This can occur for many
different reasons. Either the sensor has a large amount of debris stuck to it, there is
a mechanical problem with the pump, or there is a problem with the plumbing
connections. Please refer to the Troubleshooting Guide.
C ntr ller has l st signal fr m sens r
This alarm will sound if the controller has detected a weak signal or has lost the
signal from the sensor. Check for a secure connection between controller and sensor
wire or clean the sensor rod.
Ultimate Sens r
The Ultimate Sensor uses a unique, patented, smart sensor that has
no moving floats. A single 3.5” corrosion proof, stainless steel,
sensor rod will detect virtually any liquid. It’s imbedded smart
sensing software adjusts to the harshest conditions regardless of any
accumulated coating. The ball shaped sensor has a 10’ cord that
includes a connector that can be separated from the controller when
the cord needs to be threaded through small openings.
Note: When mounting the Ultimate Sensor, osition the bottom of the
sensor rod at the height you want the um to activate.
Installing the Ultimate Sens r
The PHCC Pro Series Ultimate Sensor is easy to install by using the
enclosed stainless steel hose clamp.
1. Hold the ball shaped sensor to
the discharge pipe so that the
sensor rod is below the ball.
2. Secure the sensor rod to the pipe
with the enclosed hose clamp,
but do not completely tighten
the clamp at this time. Be sure
to place the drive mechanism of
the clamp on the opposite side of
the sensor. This will allow the
extra material of the clamp to be
as close as possible to the sensor
once it is completely tightened.
3. Position the sensor to a level
where the bottom of the sensor
rod is no lower than 3” above the
bottom of the pump. To avoid
debris pouring onto the sensor, it
should be positioned on the side
opposite the drain tile.
Note: It is im ortant to mount
the sensor below the drain tile
that em ties into the it.
Mounting it above the drain tile
would allow water to fill the drain
tile before the um is activated
to um out the water.
4. nce the sensor is in the desired position, tighten the clamp. Do not over
tighten.
Note: Do not attem t to use sensors or float switches other than the Ultimate Sensor
with this controller.
The Ultimate S lid State C ntr ller M del # USC3
The benefit of this controller is that it will sound an alarm when problems exist or
maintenance is needed. The controller will also run the pump once a week for
approximately four (4) seconds. This test will exercise the pump and help ensure the
pump is working properly.
The PHCC Pro Series Ultimate Solid State Controller features a series of warnings
(audible and visual) that pinpoint potential problems with the pump, sensor and
power conditions. The controller will sound an alarm when power has been
interrupted, when the pump has run for more than 10 minutes continuously, when
the 9V battery is low or if the controller detects a weak or no signal from the sensor.
The 9V battery (sold separately) runs the controller during a power outage, allowing
it to sound an alarm if the circuit breaker trips, the controller is not plugged in
securely, or the home’s power is interrupted.
Note: The 9V battery will only ower the controller, not the um .
Installing the Ultimate S lid State C ntr ller
1. Mount the controller to the wall through the 2 holes on the cabinet using the
proper mounting hardware for the application. The controller should be mounted
at least 4⬘from the floor and within 4’ of the outlet.
2. pen the plastic door on the top of the unit and using a flat head screwdriver
adjust the dial to select the number of seconds that the pump will run after the
water falls below the sensor. The timer can be adjusted from 5-45 seconds. The
manufacturer default is about 10 seconds. Install a 9V alkaline battery and
replace the plastic door.
3. Plug the control box into a properly grounded, 3-prong receptacle (preferably
with ground fault circuit interrupt). Then, plug the pump into the receptacle on
the control box. Do not use an extension cord.
4. Make sure the Power Failure Alarm slide switch is in the N position.
Installati n Instructi ns
USC3 Ultimate S lid State C ntr ller
with Ultimate Sensr
Glentronics, Inc.
Lincolnshire, IL 60069
800-991-0466
www.st pfl ding.c m
1806078 04/2011
