Girard Systems 98GC1102 Instrucciones de funcionamiento

IGNITION RETRACT & LOCK MODULE

98GC1102

INSTALLATION & PROGRAMMING GUIDE

REV.12312015

RV AWNING PRODUCTS

1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500

www.girardrv.com

Page 2of 7

Girard Systems awnings may be operated in light wind and rain

conditions. When periods of heavy rain and or high wind are expected

the awning must be closed. Never leave the awning open and

unattended.

Damage caused by wind and rain is not covered by warranty.

All awnings must be closed prior to moving the vehicle for any reason.

As an extra safety precaution a visual check that every awning is fully

closed is required.

Damage caused by failure to comply with these instructions is

not covered by warranty.

Before using your awning, ensure that the area into which the awning

will be deployed is free of obstructions (Trees, walls, pillars, posts,

other vehicles etc.)

Damage caused by collisions with any of the above or similar is

not covered by warranty.

Before using your awning make sure that all of your electrical circuits

are operating correctly. Recreational Vehicles can generate AC power

from three separate sources. The electrical system transfer switch in

your vehicle will select power for the awning as follows:

Shore Power – if connected;

Generator Power – if the generator is running;

Inverter Power – batteries must be charged for inverter operation.

Girard Systems awnings are supplied with an electric motor appropriate to the

product.

Page 3of 7

CONTENTS

Product Description …………………………………………………………………………. 4

Wiring Diagrams ……………………………………………………………………………… 5

Programming Procedure .…………………………………………………………………. 6

Programming the Delay…………….……………………………………………………… 7

THE G–LINK SYSTEM

The G-Link motors and control modules provided by Girard Systems communicate by

use of RF signals on a frequency of 433.92 MHZ. This eliminates the need for wiring

and the drilling of holes in the vehicle. These components must be electronically

matched, programmed or paired before use. This is usually done at the Girard Systems

factory. Should the need arise for the user to pair a device with the motor controller

they must refer to the appropriate manual for the devices applicable to their particular

installation.

WARNING

“To reduce the risk of electric shock the operator power is to be

provided from a weatherproof junction box in the case of permanent

wiring, as per 314.15 of the National Electrical Code, NFPA 70.”

To prevent the motor protector from tripping do not exceed 2

minutes of operation per hour.

Page 4of 7

PRODUCT DESCRIPTION

The 98GC1102 Ignition Retract and Lockout Module is designed to send a retract signal

to any electronically paired G-Link motor control modules installed on the Recreational

Vehicle, whenever the engine is turned on or the parking brake released (dependent

upon the installation). The 98GC1102 can be electronically paired with more than one

motor controller, but only electrically isolates power from the motor controller that it is

connected to. This being the case it is advised that each awning on the vehicle to have

its own Ignition Retract and Lockout Module

For installations that consist of more than one awning, a delay should be set for each

additional Ignition Retract and Lockout module using the procedure described in this

manual (see programming the delay).

The 98GC1102 will send the retract signal 3 times in the first 5 seconds of the Vehicle

engine starting or the parking brake being released, this will ensure that all

electronically paired awnings have been sent a retract signal before the vehicle moves.

90 seconds after sending a “Retract” signal, the 98GC1102 will isolate power from the

motor controller to which it is connected and the power will remain isolated until the

engine is turned off again, (or the parking brake engaged) this prevents the awning

from being accidentally extended while the vehicle is in motion.

The 98GC1102 has an AC Plug to enable connection to a 110v AC power supply, It is

recommended that this plug be removed and the power supply be connected through

an approved junction box to prevent the module being connected to an unsuitable

power source. The white cable with the rectangular plug connects to the motor control

module of the awning. To enable its function the 98GC1102 requires the Black and Red

wires coming from the module to be connected to the 12 Volt Vehicle ignition circuit or

the parking brake circuit (See the wiring diagrams on the next page).

Page 5of 7

Page 6of 7

PROGRAMMING PROCEDURE

Ensure that the vehicle ignition circuit is switched OFF or the parking brake is

engaged (whichever is applicable to the installation), and the awning is

extended before connecting the 98GC1102 to the 12v DC circuit.

a) Connect the 98GC1102 to a suitable 110v AC power supply.

b) Connect the 98GC1102 to the G-Link Motor controller using the white connector

(see figure 1).

Figure 1

c) Connect the 12v wires of the 98GC1102 to the 12v ignition circuit or parking

brake circuit of the vehicle.

Note; When carrying out this part of the procedure each step must be

executed within 10 seconds of the previous one or the module will revert to

factory settings. It is highly recommended that you read and understand the

following sequence before attempting to execute it.

d) Press the PROGRAM button on the MOTOR CONTROLLER, the Green LED will

start blinking.

e) Press STOP on the MOTOR CONTROLLER, the Green LED will stop blinking and

remain illuminated.

f) Turn ON the Ignition Switch (or release the parking brake according to the

installation). The green LED will turn off and the awning should retract. The

MOTOR CONTROLLER will be disabled after 90 seconds.

g) If the unit does not work as described above repeat d), e) and f) again.

THIS PLUG CONNECTS THE 98GC1102 MODULE

TO THE AWNING’S MOTOR CONTROL MODULE

Page 7of 7

PROGRAMMING THE DELAY

a) Remove the four screws on top of the 98GC1102 to open the Lid (See figure 2).

Figure 2

Note; When carrying out this part of the procedure each step must be

executed within 5 seconds of the previous one or the module will revert to

factory settings. It is highly recommended that you read and understand the

following sequence before attempting to execute it.

b) With the engine ON press the SET button (see Figure 2) on the Ignition lockout

for 6 seconds until you hear a beep.

c) Press the UP button shown in Figure 2 to change the delay. Each press will be

followed by a beep and it will increase the delay by one second.

NOTE: Make sure the delay is different from every other Ignition Lockout in

the coach.

For queries or assistance with programming any of your G-Link devices

please call Girard Systems TOLL FREE on 800–382–8442 between 7:30am

and 3:30pm P.S.T.

UP Button

SET Button

Tabla de contenidos

Otros manuales de Unidad de control de Girard Systems

Girard Systems

Girard Systems GC1149A Manual de usuario

Girard Systems

Girard Systems GC136 Manual de usuario

Girard Systems

Girard Systems GC274B Manual de usuario

Girard Systems

Girard Systems 98GCK-45DR Guía de instalación

Girard Systems

Girard Systems 98GCK-32B Manual de usuario

Girard Systems

Girard Systems 98GCK-36A Manual de usuario

Girard Systems

Girard Systems 98GCK-16 Manual de usuario

Girard Systems

Girard Systems GC946G Manual de usuario

Girard Systems

Girard Systems GC274C Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario