Gira Observer 70 Manual de usuario

Observer 70 white

0831 02

Observer 70 anthr.

0831 10

1 Safety instructions

Electrical equipment may only be installed and fitted by electrically skilled persons.

Failure to observe the instructions may cause damage to the device and result in fire and

other hazards.

Danger of electric shock. Device is not suitable for disconnection from supply voltage.

Danger of electric shock. Always disconnect before carrying out work on the devise or

load. At the same time, take into account all circuit breakers that supply dangerous

voltage to the device or load.

Do not press on the sensor window. Device can be damaged.

The device is not suitable for use as a burglar alarm or other alarm.

These instructions are an integral part of the product, and must remain with the end

customer.

2 Device components

(1) Sensor window

(2) Rear device panel

(3) Central screw

3 Function

Intended use

- Automatic switching of lighting depending on the heat motion and ambient brightness.

- Surface-mounting in indoor and outdoor areas

Product characteristics

- Variable installation position

- Protected against spray water

1/8

82523522 19.05.2011

Observer 70

- Follow-up time and brightness value settable

- Test operation for checking the detection area

- Range can be set in three levels

- Parallel connection of multiple motion detectors possible

- Manual switch-on possible with installation button, NC contact

Automatic operation

The controller detects heat motions of people, animals and objects.

- The light is switched on if a person enters the detection area and the brightness is below

the set threshold.

- The light is switched off if no more movement is detected in the detection area and the

follow-up time has elapsed.

In order to avoid light oscillations due to the cooling of a bulb, the controller does not evaluate

any signals for approx. 3 seconds after switch-off.

2: Detection area, motion detector

4 Operation

Switching the light on manually

Optional installation button, NC contact is installed (connect the motion detector).

o Press the installation button for at least 1 second.

Light is switched on independently of the brightness for the set follow-up time.

When motions are detected, the delay time is restarted.

5 Information for electrically skilled persons

5.1 Fitting and electrical connection

Electrical shock when live parts are touched.

Electrical shocks can be fatal.

Before carrying out work on the device or load, disengage all the

corresponding circuit breakers. Cover up live parts in the working environment.

82523522 19.05.2011 2/8

Observer 70

Heat radiation too high.

Destruction of the sensors.

Align the device so that no direct sunshine hits the sensor window.

Do not place the device in the sun.

3: Installation laterally to the direction of movement

Selecting the installation location

At an installation height of 2.4 m ( 2), the optimum range of the motion detector is achieved

transversely to the direction of movement ( 3).

The range is reduced in the case of:

- The land slopes upwards away from the motion detector

- Internal housing in middle or lower lock ( 6)

- Low temperature difference

- Installation height less than 2.4 m

- Effects of weather, e.g. rain, fog or snow

The range is increased in the case of:

- The land slopes downwards away from the motion detector

- High temperature difference

- Installation height greater than 2.4 m

o Select a vibration-free installation location; vibrations can lead to unwanted switching.

o Avoid interference sources in the detection area. Interference sources, e.g. heaters,

ventilation, air conditioners, or cooling light bulbs can lead to unwanted switching.

o Take direction of motion into account.

o Determine installation height.

i To achieve a rapid response from the motion detector on leaving the building, install the

device at a height of less than 2.4 m, centrally above the door.

Installing the motion detector

o Slacken central screw (3) ( 1).

o Remove the housing cover.

82523522 19.05.2011 3/8

Observer 70

4: Rear housing panel and installation frame

i To prevent the ingress of moisture, we recommend inserting the cables from below (10).

o When the cables enter below, use an installation frame (9). Insert the rear housing panel

(7) into the installation frame.

o Do not use an installation frame for surface cable entry from the side or from above, but

instead penetrate one of the the thinner areas of the rear housing panel.

i Do not remove the water-permeable closure of the condensation water hole (8).

o Run the connection cable into the connection compartment through a rubber sleeve (4).

o Fasten the rear housing panel on the installation location with two screws (6) in such a way

that the condensation water hole is at the bottom.

Configuring the motion detector

On the rear side of the housing cover of the motion detector, there is one adjuster each for the

follow-up time (11) and the brightness threshold (12) ( 5).

5: Setting the follow-up time and the brightness threshold

The range of the motion detector can be set in three stages by sliding the internal housing (13)

( 6).

82523522 19.05.2011 4/8

Observer 70

6: Setting the range

o Set the required follow-up time using the adjuster (11).

o Set the required brightness threshold with the adjuster (12). The 3 icon stands for Day

mode, i.e. switching independent of brightness, and the 2 icon for minimum brightness.

i Should the device need to switch at the start of twilight, then set the adjuster (12) as shown

in ( 5).

o Set the range by sliding the internal housing ( 6).

Top lock (14) Maximum range

Centre lock (14) Medium range

Bottom lock (14) Minimum range

o Measure the detection area by walking it. To do this, switch the motion detector to test

mode. Set the follow-up time to 10 seconds and the brightness value to 3.

Connecting the controller

7: Stripping the connection cable

The connection cables are equipped with screwless terminals. For secure contacting, connect

only single-wire cables with a cross-section of maximum 2.5 mm². Observe the stripping lengths

for external cable jacketing and basic insulation ( 7).

blue, BU N, neutral conductor

brown, BN 8 Lamp cable

black, BK L, conductor

o Insert the screwless terminals for fixing into the holders (5) of the housing cover ( 4).

82523522 19.05.2011 5/8

Observer 70

8: Motion detector connection diagram

o Connect controller and optional installation button T, NC contact, according to connection

diagram ( 8).

o If multiple motion detectors are to switch a shared load, connect the motion detectors in

parallel.

i Parallel switching of multiple motion detectors does not increase maximum connected load.

9: Connection diagram, switching off motion detectors

The motion detector can be switched off using installation switch S1 or S2 ( 9). Switching

installation switch S1 on again triggers switch-on for the follow-up time. Installation S2 does not

do this.

82523522 19.05.2011 6/8

Observer 70

10: Connection diagram, Automatic manual mode

Installation switch S1 ( 10) can be used to switch Automatic mode on and off. Installation switch

S2 can be used to switch Manual mode on and off.

o Lock the housing cover into the bottom of the rear housing panel, push the top down and

screw it tight with the central screw (3).

6 Appendix

6.1 Technical data

Rated voltage AC 230 V ~

Mains frequency 50 Hz

Power consumption approx. 1.1 W

Ambient temperature -25 ... +55 °C

Protection rating IP 55

Circuit breaker max. 10 A

Installation height approx. 2.40 m

Detection angle approx. 70 °

run-on time approx. 10 s ... 5 min

Connected load

Incandescent lamps 1000 W

HV halogen lamps 1000 W

Tronic transformers 750 W

Inductive transformers 750 VA

Electronic ballast Type-dependent

Fluorescent lamps, uncompensated 500 VA

Fluorescent lamps, parallel compensated 400 VA

Switching current

Minimum switching current AC 100 mA

Contact type µ contact

Connection

Single stranded max. 2.5 mm²

6.2 Warranty

The warranty is provided in accordance with statutory requirements via the specialist trade.

Please submit or send faulty devices postage paid together with an error description to your

responsible salesperson (specialist trade/installation company/electrical specialist trade). They

will forward the devices to the Gira Service Center.

82523522 19.05.2011 7/8

Observer 70

Gira

Giersiepen GmbH & Co. KG

Elektro-Installations-

Systeme

Industriegebiet Mermbach

Dahlienstraße

42477 Radevormwald

Postfach 12 20

42461 Radevormwald

Deutschland

Tel +49(0)21 95 - 602-0

Fax +49(0)21 95 - 602-399

www.gira.de

[email protected]

82523522 19.05.2011 8/8

Observer 70

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de Gira

Gira

Gira 5472 02 Manual de usuario

Gira

Gira 0384 00 Manual de usuario

Gira

Gira 2688 Series Manual de usuario

Gira

Gira 5068 00 Manual de usuario

Gira

Gira 5472 02 Manual de usuario

Gira

Gira EDA 3902 F Manual de usuario

Gira

Gira KNX/EIB Manual de usuario

Gira

Gira 5466 02 Manual de usuario

Gira

Gira 5111 00 Manual de usuario

Gira

Gira 0551 4 Series Manual de usuario

Gira

Gira 234902 Manual de usuario

Gira

Gira 1170 Series Manual de usuario

Gira

Gira 5466 02 Manual de usuario

Gira

Gira 1025 00 Manual de usuario

Gira

Gira Touch sensor 2 Manual de usuario

Gira

Gira 5471 00 Manual de usuario

Gira

Gira 0873 00 Manual de usuario

Gira

Gira System 55 Pushbutton sensor 4 Standard Manual de usuario

Gira

Gira 5069 00 Manual de usuario

Gira

Gira KNX 5011 00 Manual de usuario

Gira

Gira 1117 00 Manual de usuario

Gira

Gira System 106 Manual de usuario

Gira

Gira 5142 00 Manual del operador

Gira

Gira 1493 00 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario